| /* | |
| * arch/v850/kernel/ma.c -- V850E/MA series of cpu chips | |
| * | |
| * Copyright (C) 2001,02,03 NEC Electronics Corporation | |
| * Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org> | |
| * | |
| * This file is subject to the terms and conditions of the GNU General | |
| * Public License. See the file COPYING in the main directory of this | |
| * archive for more details. | |
| * | |
| * Written by Miles Bader <miles@gnu.org> | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/mm.h> | |
| #include <linux/swap.h> | |
| #include <linux/bootmem.h> | |
| #include <linux/irq.h> | |
| #include <asm/atomic.h> | |
| #include <asm/page.h> | |
| #include <asm/machdep.h> | |
| #include <asm/v850e_timer_d.h> | |
| #include "mach.h" | |
| void __init mach_sched_init (struct irqaction *timer_action) | |
| { | |
| /* Start hardware timer. */ | |
| v850e_timer_d_configure (0, HZ); | |
| /* Install timer interrupt handler. */ | |
| setup_irq (IRQ_INTCMD(0), timer_action); | |
| } | |
| static struct v850e_intc_irq_init irq_inits[] = { | |
| { "IRQ", 0, NUM_MACH_IRQS, 1, 7 }, | |
| { "CMD", IRQ_INTCMD(0), IRQ_INTCMD_NUM, 1, 5 }, | |
| { "DMA", IRQ_INTDMA(0), IRQ_INTDMA_NUM, 1, 2 }, | |
| { "CSI", IRQ_INTCSI(0), IRQ_INTCSI_NUM, 4, 4 }, | |
| { "SER", IRQ_INTSER(0), IRQ_INTSER_NUM, 4, 3 }, | |
| { "SR", IRQ_INTSR(0), IRQ_INTSR_NUM, 4, 4 }, | |
| { "ST", IRQ_INTST(0), IRQ_INTST_NUM, 4, 5 }, | |
| { 0 } | |
| }; | |
| #define NUM_IRQ_INITS (ARRAY_SIZE(irq_inits) - 1) | |
| static struct hw_interrupt_type hw_itypes[NUM_IRQ_INITS]; | |
| /* Initialize MA chip interrupts. */ | |
| void __init ma_init_irqs (void) | |
| { | |
| v850e_intc_init_irq_types (irq_inits, hw_itypes); | |
| } | |
| /* Called before configuring an on-chip UART. */ | |
| void ma_uart_pre_configure (unsigned chan, unsigned cflags, unsigned baud) | |
| { | |
| /* We only know about the first two UART channels (though | |
| specific chips may have more). */ | |
| if (chan < 2) { | |
| unsigned bits = 0x3 << (chan * 3); | |
| /* Specify that the relevant pins on the chip should do | |
| serial I/O, not direct I/O. */ | |
| MA_PORT4_PMC |= bits; | |
| /* Specify that we're using the UART, not the CSI device. */ | |
| MA_PORT4_PFC |= bits; | |
| } | |
| } |