| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Qualcomm PCIe root complex driver |
| * |
| * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved. |
| * Copyright 2015 Linaro Limited. |
| * |
| * Author: Stanimir Varbanov <svarbanov@mm-sol.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/of_device.h> |
| #include <linux/of_gpio.h> |
| #include <linux/pci.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/platform_device.h> |
| #include <linux/phy/phy.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/reset.h> |
| #include <linux/slab.h> |
| #include <linux/types.h> |
| |
| #include "pcie-designware.h" |
| |
| #define PCIE20_PARF_SYS_CTRL 0x00 |
| #define MST_WAKEUP_EN BIT(13) |
| #define SLV_WAKEUP_EN BIT(12) |
| #define MSTR_ACLK_CGC_DIS BIT(10) |
| #define SLV_ACLK_CGC_DIS BIT(9) |
| #define CORE_CLK_CGC_DIS BIT(6) |
| #define AUX_PWR_DET BIT(4) |
| #define L23_CLK_RMV_DIS BIT(2) |
| #define L1_CLK_RMV_DIS BIT(1) |
| |
| #define PCIE20_COMMAND_STATUS 0x04 |
| #define CMD_BME_VAL 0x4 |
| #define PCIE20_DEVICE_CONTROL2_STATUS2 0x98 |
| #define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10 |
| |
| #define PCIE20_PARF_PHY_CTRL 0x40 |
| #define PCIE20_PARF_PHY_REFCLK 0x4C |
| #define PCIE20_PARF_DBI_BASE_ADDR 0x168 |
| #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16C |
| #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174 |
| #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x178 |
| #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 0x1A8 |
| #define PCIE20_PARF_LTSSM 0x1B0 |
| #define PCIE20_PARF_SID_OFFSET 0x234 |
| #define PCIE20_PARF_BDF_TRANSLATE_CFG 0x24C |
| |
| #define PCIE20_ELBI_SYS_CTRL 0x04 |
| #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE BIT(0) |
| |
| #define PCIE20_AXI_MSTR_RESP_COMP_CTRL0 0x818 |
| #define CFG_REMOTE_RD_REQ_BRIDGE_SIZE_2K 0x4 |
| #define CFG_REMOTE_RD_REQ_BRIDGE_SIZE_4K 0x5 |
| #define PCIE20_AXI_MSTR_RESP_COMP_CTRL1 0x81c |
| #define CFG_BRIDGE_SB_INIT BIT(0) |
| |
| #define PCIE20_CAP 0x70 |
| #define PCIE20_CAP_LINK_CAPABILITIES (PCIE20_CAP + 0xC) |
| #define PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT (BIT(10) | BIT(11)) |
| #define PCIE20_CAP_LINK_1 (PCIE20_CAP + 0x14) |
| #define PCIE_CAP_LINK1_VAL 0x2FD7F |
| |
| #define PCIE20_PARF_Q2A_FLUSH 0x1AC |
| |
| #define PCIE20_MISC_CONTROL_1_REG 0x8BC |
| #define DBI_RO_WR_EN 1 |
| |
| #define PERST_DELAY_US 1000 |
| |
| #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358 |
| #define SLV_ADDR_SPACE_SZ 0x10000000 |
| |
| #define QCOM_PCIE_2_1_0_MAX_SUPPLY 3 |
| struct qcom_pcie_resources_2_1_0 { |
| struct clk *iface_clk; |
| struct clk *core_clk; |
| struct clk *phy_clk; |
| struct reset_control *pci_reset; |
| struct reset_control *axi_reset; |
| struct reset_control *ahb_reset; |
| struct reset_control *por_reset; |
| struct reset_control *phy_reset; |
| struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY]; |
| }; |
| |
| struct qcom_pcie_resources_1_0_0 { |
| struct clk *iface; |
| struct clk *aux; |
| struct clk *master_bus; |
| struct clk *slave_bus; |
| struct reset_control *core; |
| struct regulator *vdda; |
| }; |
| |
| #define QCOM_PCIE_2_3_2_MAX_SUPPLY 2 |
| struct qcom_pcie_resources_2_3_2 { |
| struct clk *aux_clk; |
| struct clk *master_clk; |
| struct clk *slave_clk; |
| struct clk *cfg_clk; |
| struct clk *pipe_clk; |
| struct regulator_bulk_data supplies[QCOM_PCIE_2_3_2_MAX_SUPPLY]; |
| }; |
| |
| struct qcom_pcie_resources_2_4_0 { |
| struct clk *aux_clk; |
| struct clk *master_clk; |
| struct clk *slave_clk; |
| struct reset_control *axi_m_reset; |
| struct reset_control *axi_s_reset; |
| struct reset_control *pipe_reset; |
| struct reset_control *axi_m_vmid_reset; |
| struct reset_control *axi_s_xpu_reset; |
| struct reset_control *parf_reset; |
| struct reset_control *phy_reset; |
| struct reset_control *axi_m_sticky_reset; |
| struct reset_control *pipe_sticky_reset; |
| struct reset_control *pwr_reset; |
| struct reset_control *ahb_reset; |
| struct reset_control *phy_ahb_reset; |
| }; |
| |
| struct qcom_pcie_resources_2_3_3 { |
| struct clk *iface; |
| struct clk *axi_m_clk; |
| struct clk *axi_s_clk; |
| struct clk *ahb_clk; |
| struct clk *aux_clk; |
| struct reset_control *rst[7]; |
| }; |
| |
| union qcom_pcie_resources { |
| struct qcom_pcie_resources_1_0_0 v1_0_0; |
| struct qcom_pcie_resources_2_1_0 v2_1_0; |
| struct qcom_pcie_resources_2_3_2 v2_3_2; |
| struct qcom_pcie_resources_2_3_3 v2_3_3; |
| struct qcom_pcie_resources_2_4_0 v2_4_0; |
| }; |
| |
| struct qcom_pcie; |
| |
| struct qcom_pcie_ops { |
| int (*get_resources)(struct qcom_pcie *pcie); |
| int (*init)(struct qcom_pcie *pcie); |
| int (*post_init)(struct qcom_pcie *pcie); |
| void (*deinit)(struct qcom_pcie *pcie); |
| void (*post_deinit)(struct qcom_pcie *pcie); |
| void (*ltssm_enable)(struct qcom_pcie *pcie); |
| }; |
| |
| struct qcom_pcie { |
| struct dw_pcie *pci; |
| void __iomem *parf; /* DT parf */ |
| void __iomem *elbi; /* DT elbi */ |
| union qcom_pcie_resources res; |
| struct phy *phy; |
| struct gpio_desc *reset; |
| const struct qcom_pcie_ops *ops; |
| }; |
| |
| #define to_qcom_pcie(x) dev_get_drvdata((x)->dev) |
| |
| static void qcom_ep_reset_assert(struct qcom_pcie *pcie) |
| { |
| gpiod_set_value_cansleep(pcie->reset, 1); |
| usleep_range(PERST_DELAY_US, PERST_DELAY_US + 500); |
| } |
| |
| static void qcom_ep_reset_deassert(struct qcom_pcie *pcie) |
| { |
| gpiod_set_value_cansleep(pcie->reset, 0); |
| usleep_range(PERST_DELAY_US, PERST_DELAY_US + 500); |
| } |
| |
| static int qcom_pcie_establish_link(struct qcom_pcie *pcie) |
| { |
| struct dw_pcie *pci = pcie->pci; |
| |
| if (dw_pcie_link_up(pci)) |
| return 0; |
| |
| /* Enable Link Training state machine */ |
| if (pcie->ops->ltssm_enable) |
| pcie->ops->ltssm_enable(pcie); |
| |
| return dw_pcie_wait_for_link(pci); |
| } |
| |
| static void qcom_pcie_2_1_0_ltssm_enable(struct qcom_pcie *pcie) |
| { |
| u32 val; |
| |
| /* enable link training */ |
| val = readl(pcie->elbi + PCIE20_ELBI_SYS_CTRL); |
| val |= PCIE20_ELBI_SYS_CTRL_LT_ENABLE; |
| writel(val, pcie->elbi + PCIE20_ELBI_SYS_CTRL); |
| } |
| |
| static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| int ret; |
| |
| res->supplies[0].supply = "vdda"; |
| res->supplies[1].supply = "vdda_phy"; |
| res->supplies[2].supply = "vdda_refclk"; |
| ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(res->supplies), |
| res->supplies); |
| if (ret) |
| return ret; |
| |
| res->iface_clk = devm_clk_get(dev, "iface"); |
| if (IS_ERR(res->iface_clk)) |
| return PTR_ERR(res->iface_clk); |
| |
| res->core_clk = devm_clk_get(dev, "core"); |
| if (IS_ERR(res->core_clk)) |
| return PTR_ERR(res->core_clk); |
| |
| res->phy_clk = devm_clk_get(dev, "phy"); |
| if (IS_ERR(res->phy_clk)) |
| return PTR_ERR(res->phy_clk); |
| |
| res->pci_reset = devm_reset_control_get_exclusive(dev, "pci"); |
| if (IS_ERR(res->pci_reset)) |
| return PTR_ERR(res->pci_reset); |
| |
| res->axi_reset = devm_reset_control_get_exclusive(dev, "axi"); |
| if (IS_ERR(res->axi_reset)) |
| return PTR_ERR(res->axi_reset); |
| |
| res->ahb_reset = devm_reset_control_get_exclusive(dev, "ahb"); |
| if (IS_ERR(res->ahb_reset)) |
| return PTR_ERR(res->ahb_reset); |
| |
| res->por_reset = devm_reset_control_get_exclusive(dev, "por"); |
| if (IS_ERR(res->por_reset)) |
| return PTR_ERR(res->por_reset); |
| |
| res->phy_reset = devm_reset_control_get_exclusive(dev, "phy"); |
| return PTR_ERR_OR_ZERO(res->phy_reset); |
| } |
| |
| static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; |
| |
| reset_control_assert(res->pci_reset); |
| reset_control_assert(res->axi_reset); |
| reset_control_assert(res->ahb_reset); |
| reset_control_assert(res->por_reset); |
| reset_control_assert(res->pci_reset); |
| clk_disable_unprepare(res->iface_clk); |
| clk_disable_unprepare(res->core_clk); |
| clk_disable_unprepare(res->phy_clk); |
| regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); |
| } |
| |
| static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| u32 val; |
| int ret; |
| |
| ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies); |
| if (ret < 0) { |
| dev_err(dev, "cannot enable regulators\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->ahb_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert ahb reset\n"); |
| goto err_assert_ahb; |
| } |
| |
| ret = clk_prepare_enable(res->iface_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable iface clock\n"); |
| goto err_assert_ahb; |
| } |
| |
| ret = clk_prepare_enable(res->phy_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable phy clock\n"); |
| goto err_clk_phy; |
| } |
| |
| ret = clk_prepare_enable(res->core_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable core clock\n"); |
| goto err_clk_core; |
| } |
| |
| ret = reset_control_deassert(res->ahb_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert ahb reset\n"); |
| goto err_deassert_ahb; |
| } |
| |
| /* enable PCIe clocks and resets */ |
| val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); |
| val &= ~BIT(0); |
| writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); |
| |
| /* enable external reference clock */ |
| val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK); |
| val |= BIT(16); |
| writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK); |
| |
| ret = reset_control_deassert(res->phy_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert phy reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_deassert(res->pci_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert pci reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_deassert(res->por_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert por reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_deassert(res->axi_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert axi reset\n"); |
| return ret; |
| } |
| |
| /* wait for clock acquisition */ |
| usleep_range(1000, 1500); |
| |
| |
| /* Set the Max TLP size to 2K, instead of using default of 4K */ |
| writel(CFG_REMOTE_RD_REQ_BRIDGE_SIZE_2K, |
| pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL0); |
| writel(CFG_BRIDGE_SB_INIT, |
| pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1); |
| |
| return 0; |
| |
| err_deassert_ahb: |
| clk_disable_unprepare(res->core_clk); |
| err_clk_core: |
| clk_disable_unprepare(res->phy_clk); |
| err_clk_phy: |
| clk_disable_unprepare(res->iface_clk); |
| err_assert_ahb: |
| regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); |
| |
| return ret; |
| } |
| |
| static int qcom_pcie_get_resources_1_0_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| |
| res->vdda = devm_regulator_get(dev, "vdda"); |
| if (IS_ERR(res->vdda)) |
| return PTR_ERR(res->vdda); |
| |
| res->iface = devm_clk_get(dev, "iface"); |
| if (IS_ERR(res->iface)) |
| return PTR_ERR(res->iface); |
| |
| res->aux = devm_clk_get(dev, "aux"); |
| if (IS_ERR(res->aux)) |
| return PTR_ERR(res->aux); |
| |
| res->master_bus = devm_clk_get(dev, "master_bus"); |
| if (IS_ERR(res->master_bus)) |
| return PTR_ERR(res->master_bus); |
| |
| res->slave_bus = devm_clk_get(dev, "slave_bus"); |
| if (IS_ERR(res->slave_bus)) |
| return PTR_ERR(res->slave_bus); |
| |
| res->core = devm_reset_control_get_exclusive(dev, "core"); |
| return PTR_ERR_OR_ZERO(res->core); |
| } |
| |
| static void qcom_pcie_deinit_1_0_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0; |
| |
| reset_control_assert(res->core); |
| clk_disable_unprepare(res->slave_bus); |
| clk_disable_unprepare(res->master_bus); |
| clk_disable_unprepare(res->iface); |
| clk_disable_unprepare(res->aux); |
| regulator_disable(res->vdda); |
| } |
| |
| static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| int ret; |
| |
| ret = reset_control_deassert(res->core); |
| if (ret) { |
| dev_err(dev, "cannot deassert core reset\n"); |
| return ret; |
| } |
| |
| ret = clk_prepare_enable(res->aux); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable aux clock\n"); |
| goto err_res; |
| } |
| |
| ret = clk_prepare_enable(res->iface); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable iface clock\n"); |
| goto err_aux; |
| } |
| |
| ret = clk_prepare_enable(res->master_bus); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable master_bus clock\n"); |
| goto err_iface; |
| } |
| |
| ret = clk_prepare_enable(res->slave_bus); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable slave_bus clock\n"); |
| goto err_master; |
| } |
| |
| ret = regulator_enable(res->vdda); |
| if (ret) { |
| dev_err(dev, "cannot enable vdda regulator\n"); |
| goto err_slave; |
| } |
| |
| /* change DBI base address */ |
| writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); |
| |
| if (IS_ENABLED(CONFIG_PCI_MSI)) { |
| u32 val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT); |
| |
| val |= BIT(31); |
| writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT); |
| } |
| |
| return 0; |
| err_slave: |
| clk_disable_unprepare(res->slave_bus); |
| err_master: |
| clk_disable_unprepare(res->master_bus); |
| err_iface: |
| clk_disable_unprepare(res->iface); |
| err_aux: |
| clk_disable_unprepare(res->aux); |
| err_res: |
| reset_control_assert(res->core); |
| |
| return ret; |
| } |
| |
| static void qcom_pcie_2_3_2_ltssm_enable(struct qcom_pcie *pcie) |
| { |
| u32 val; |
| |
| /* enable link training */ |
| val = readl(pcie->parf + PCIE20_PARF_LTSSM); |
| val |= BIT(8); |
| writel(val, pcie->parf + PCIE20_PARF_LTSSM); |
| } |
| |
| static int qcom_pcie_get_resources_2_3_2(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| int ret; |
| |
| res->supplies[0].supply = "vdda"; |
| res->supplies[1].supply = "vddpe-3v3"; |
| ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(res->supplies), |
| res->supplies); |
| if (ret) |
| return ret; |
| |
| res->aux_clk = devm_clk_get(dev, "aux"); |
| if (IS_ERR(res->aux_clk)) |
| return PTR_ERR(res->aux_clk); |
| |
| res->cfg_clk = devm_clk_get(dev, "cfg"); |
| if (IS_ERR(res->cfg_clk)) |
| return PTR_ERR(res->cfg_clk); |
| |
| res->master_clk = devm_clk_get(dev, "bus_master"); |
| if (IS_ERR(res->master_clk)) |
| return PTR_ERR(res->master_clk); |
| |
| res->slave_clk = devm_clk_get(dev, "bus_slave"); |
| if (IS_ERR(res->slave_clk)) |
| return PTR_ERR(res->slave_clk); |
| |
| res->pipe_clk = devm_clk_get(dev, "pipe"); |
| return PTR_ERR_OR_ZERO(res->pipe_clk); |
| } |
| |
| static void qcom_pcie_deinit_2_3_2(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2; |
| |
| clk_disable_unprepare(res->slave_clk); |
| clk_disable_unprepare(res->master_clk); |
| clk_disable_unprepare(res->cfg_clk); |
| clk_disable_unprepare(res->aux_clk); |
| |
| regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); |
| } |
| |
| static void qcom_pcie_post_deinit_2_3_2(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2; |
| |
| clk_disable_unprepare(res->pipe_clk); |
| } |
| |
| static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| u32 val; |
| int ret; |
| |
| ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies); |
| if (ret < 0) { |
| dev_err(dev, "cannot enable regulators\n"); |
| return ret; |
| } |
| |
| ret = clk_prepare_enable(res->aux_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable aux clock\n"); |
| goto err_aux_clk; |
| } |
| |
| ret = clk_prepare_enable(res->cfg_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable cfg clock\n"); |
| goto err_cfg_clk; |
| } |
| |
| ret = clk_prepare_enable(res->master_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable master clock\n"); |
| goto err_master_clk; |
| } |
| |
| ret = clk_prepare_enable(res->slave_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable slave clock\n"); |
| goto err_slave_clk; |
| } |
| |
| /* enable PCIe clocks and resets */ |
| val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); |
| val &= ~BIT(0); |
| writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); |
| |
| /* change DBI base address */ |
| writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); |
| |
| /* MAC PHY_POWERDOWN MUX DISABLE */ |
| val = readl(pcie->parf + PCIE20_PARF_SYS_CTRL); |
| val &= ~BIT(29); |
| writel(val, pcie->parf + PCIE20_PARF_SYS_CTRL); |
| |
| val = readl(pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); |
| val |= BIT(4); |
| writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); |
| |
| val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2); |
| val |= BIT(31); |
| writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2); |
| |
| return 0; |
| |
| err_slave_clk: |
| clk_disable_unprepare(res->master_clk); |
| err_master_clk: |
| clk_disable_unprepare(res->cfg_clk); |
| err_cfg_clk: |
| clk_disable_unprepare(res->aux_clk); |
| |
| err_aux_clk: |
| regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); |
| |
| return ret; |
| } |
| |
| static int qcom_pcie_post_init_2_3_2(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| int ret; |
| |
| ret = clk_prepare_enable(res->pipe_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable pipe clock\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int qcom_pcie_get_resources_2_4_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| |
| res->aux_clk = devm_clk_get(dev, "aux"); |
| if (IS_ERR(res->aux_clk)) |
| return PTR_ERR(res->aux_clk); |
| |
| res->master_clk = devm_clk_get(dev, "master_bus"); |
| if (IS_ERR(res->master_clk)) |
| return PTR_ERR(res->master_clk); |
| |
| res->slave_clk = devm_clk_get(dev, "slave_bus"); |
| if (IS_ERR(res->slave_clk)) |
| return PTR_ERR(res->slave_clk); |
| |
| res->axi_m_reset = devm_reset_control_get_exclusive(dev, "axi_m"); |
| if (IS_ERR(res->axi_m_reset)) |
| return PTR_ERR(res->axi_m_reset); |
| |
| res->axi_s_reset = devm_reset_control_get_exclusive(dev, "axi_s"); |
| if (IS_ERR(res->axi_s_reset)) |
| return PTR_ERR(res->axi_s_reset); |
| |
| res->pipe_reset = devm_reset_control_get_exclusive(dev, "pipe"); |
| if (IS_ERR(res->pipe_reset)) |
| return PTR_ERR(res->pipe_reset); |
| |
| res->axi_m_vmid_reset = devm_reset_control_get_exclusive(dev, |
| "axi_m_vmid"); |
| if (IS_ERR(res->axi_m_vmid_reset)) |
| return PTR_ERR(res->axi_m_vmid_reset); |
| |
| res->axi_s_xpu_reset = devm_reset_control_get_exclusive(dev, |
| "axi_s_xpu"); |
| if (IS_ERR(res->axi_s_xpu_reset)) |
| return PTR_ERR(res->axi_s_xpu_reset); |
| |
| res->parf_reset = devm_reset_control_get_exclusive(dev, "parf"); |
| if (IS_ERR(res->parf_reset)) |
| return PTR_ERR(res->parf_reset); |
| |
| res->phy_reset = devm_reset_control_get_exclusive(dev, "phy"); |
| if (IS_ERR(res->phy_reset)) |
| return PTR_ERR(res->phy_reset); |
| |
| res->axi_m_sticky_reset = devm_reset_control_get_exclusive(dev, |
| "axi_m_sticky"); |
| if (IS_ERR(res->axi_m_sticky_reset)) |
| return PTR_ERR(res->axi_m_sticky_reset); |
| |
| res->pipe_sticky_reset = devm_reset_control_get_exclusive(dev, |
| "pipe_sticky"); |
| if (IS_ERR(res->pipe_sticky_reset)) |
| return PTR_ERR(res->pipe_sticky_reset); |
| |
| res->pwr_reset = devm_reset_control_get_exclusive(dev, "pwr"); |
| if (IS_ERR(res->pwr_reset)) |
| return PTR_ERR(res->pwr_reset); |
| |
| res->ahb_reset = devm_reset_control_get_exclusive(dev, "ahb"); |
| if (IS_ERR(res->ahb_reset)) |
| return PTR_ERR(res->ahb_reset); |
| |
| res->phy_ahb_reset = devm_reset_control_get_exclusive(dev, "phy_ahb"); |
| if (IS_ERR(res->phy_ahb_reset)) |
| return PTR_ERR(res->phy_ahb_reset); |
| |
| return 0; |
| } |
| |
| static void qcom_pcie_deinit_2_4_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0; |
| |
| reset_control_assert(res->axi_m_reset); |
| reset_control_assert(res->axi_s_reset); |
| reset_control_assert(res->pipe_reset); |
| reset_control_assert(res->pipe_sticky_reset); |
| reset_control_assert(res->phy_reset); |
| reset_control_assert(res->phy_ahb_reset); |
| reset_control_assert(res->axi_m_sticky_reset); |
| reset_control_assert(res->pwr_reset); |
| reset_control_assert(res->ahb_reset); |
| clk_disable_unprepare(res->aux_clk); |
| clk_disable_unprepare(res->master_clk); |
| clk_disable_unprepare(res->slave_clk); |
| } |
| |
| static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| u32 val; |
| int ret; |
| |
| ret = reset_control_assert(res->axi_m_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert axi master reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->axi_s_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert axi slave reset\n"); |
| return ret; |
| } |
| |
| usleep_range(10000, 12000); |
| |
| ret = reset_control_assert(res->pipe_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert pipe reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->pipe_sticky_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert pipe sticky reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->phy_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert phy reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->phy_ahb_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert phy ahb reset\n"); |
| return ret; |
| } |
| |
| usleep_range(10000, 12000); |
| |
| ret = reset_control_assert(res->axi_m_sticky_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert axi master sticky reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->pwr_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert power reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_assert(res->ahb_reset); |
| if (ret) { |
| dev_err(dev, "cannot assert ahb reset\n"); |
| return ret; |
| } |
| |
| usleep_range(10000, 12000); |
| |
| ret = reset_control_deassert(res->phy_ahb_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert phy ahb reset\n"); |
| return ret; |
| } |
| |
| ret = reset_control_deassert(res->phy_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert phy reset\n"); |
| goto err_rst_phy; |
| } |
| |
| ret = reset_control_deassert(res->pipe_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert pipe reset\n"); |
| goto err_rst_pipe; |
| } |
| |
| ret = reset_control_deassert(res->pipe_sticky_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert pipe sticky reset\n"); |
| goto err_rst_pipe_sticky; |
| } |
| |
| usleep_range(10000, 12000); |
| |
| ret = reset_control_deassert(res->axi_m_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert axi master reset\n"); |
| goto err_rst_axi_m; |
| } |
| |
| ret = reset_control_deassert(res->axi_m_sticky_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert axi master sticky reset\n"); |
| goto err_rst_axi_m_sticky; |
| } |
| |
| ret = reset_control_deassert(res->axi_s_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert axi slave reset\n"); |
| goto err_rst_axi_s; |
| } |
| |
| ret = reset_control_deassert(res->pwr_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert power reset\n"); |
| goto err_rst_pwr; |
| } |
| |
| ret = reset_control_deassert(res->ahb_reset); |
| if (ret) { |
| dev_err(dev, "cannot deassert ahb reset\n"); |
| goto err_rst_ahb; |
| } |
| |
| usleep_range(10000, 12000); |
| |
| ret = clk_prepare_enable(res->aux_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable iface clock\n"); |
| goto err_clk_aux; |
| } |
| |
| ret = clk_prepare_enable(res->master_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable core clock\n"); |
| goto err_clk_axi_m; |
| } |
| |
| ret = clk_prepare_enable(res->slave_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable phy clock\n"); |
| goto err_clk_axi_s; |
| } |
| |
| /* enable PCIe clocks and resets */ |
| val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); |
| val &= ~BIT(0); |
| writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); |
| |
| /* change DBI base address */ |
| writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); |
| |
| /* MAC PHY_POWERDOWN MUX DISABLE */ |
| val = readl(pcie->parf + PCIE20_PARF_SYS_CTRL); |
| val &= ~BIT(29); |
| writel(val, pcie->parf + PCIE20_PARF_SYS_CTRL); |
| |
| val = readl(pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); |
| val |= BIT(4); |
| writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); |
| |
| val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2); |
| val |= BIT(31); |
| writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2); |
| |
| return 0; |
| |
| err_clk_axi_s: |
| clk_disable_unprepare(res->master_clk); |
| err_clk_axi_m: |
| clk_disable_unprepare(res->aux_clk); |
| err_clk_aux: |
| reset_control_assert(res->ahb_reset); |
| err_rst_ahb: |
| reset_control_assert(res->pwr_reset); |
| err_rst_pwr: |
| reset_control_assert(res->axi_s_reset); |
| err_rst_axi_s: |
| reset_control_assert(res->axi_m_sticky_reset); |
| err_rst_axi_m_sticky: |
| reset_control_assert(res->axi_m_reset); |
| err_rst_axi_m: |
| reset_control_assert(res->pipe_sticky_reset); |
| err_rst_pipe_sticky: |
| reset_control_assert(res->pipe_reset); |
| err_rst_pipe: |
| reset_control_assert(res->phy_reset); |
| err_rst_phy: |
| reset_control_assert(res->phy_ahb_reset); |
| return ret; |
| } |
| |
| static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| int i; |
| const char *rst_names[] = { "axi_m", "axi_s", "pipe", |
| "axi_m_sticky", "sticky", |
| "ahb", "sleep", }; |
| |
| res->iface = devm_clk_get(dev, "iface"); |
| if (IS_ERR(res->iface)) |
| return PTR_ERR(res->iface); |
| |
| res->axi_m_clk = devm_clk_get(dev, "axi_m"); |
| if (IS_ERR(res->axi_m_clk)) |
| return PTR_ERR(res->axi_m_clk); |
| |
| res->axi_s_clk = devm_clk_get(dev, "axi_s"); |
| if (IS_ERR(res->axi_s_clk)) |
| return PTR_ERR(res->axi_s_clk); |
| |
| res->ahb_clk = devm_clk_get(dev, "ahb"); |
| if (IS_ERR(res->ahb_clk)) |
| return PTR_ERR(res->ahb_clk); |
| |
| res->aux_clk = devm_clk_get(dev, "aux"); |
| if (IS_ERR(res->aux_clk)) |
| return PTR_ERR(res->aux_clk); |
| |
| for (i = 0; i < ARRAY_SIZE(rst_names); i++) { |
| res->rst[i] = devm_reset_control_get(dev, rst_names[i]); |
| if (IS_ERR(res->rst[i])) |
| return PTR_ERR(res->rst[i]); |
| } |
| |
| return 0; |
| } |
| |
| static void qcom_pcie_deinit_2_3_3(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; |
| |
| clk_disable_unprepare(res->iface); |
| clk_disable_unprepare(res->axi_m_clk); |
| clk_disable_unprepare(res->axi_s_clk); |
| clk_disable_unprepare(res->ahb_clk); |
| clk_disable_unprepare(res->aux_clk); |
| } |
| |
| static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie) |
| { |
| struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3; |
| struct dw_pcie *pci = pcie->pci; |
| struct device *dev = pci->dev; |
| int i, ret; |
| u32 val; |
| |
| for (i = 0; i < ARRAY_SIZE(res->rst); i++) { |
| ret = reset_control_assert(res->rst[i]); |
| if (ret) { |
| dev_err(dev, "reset #%d assert failed (%d)\n", i, ret); |
| return ret; |
| } |
| } |
| |
| usleep_range(2000, 2500); |
| |
| for (i = 0; i < ARRAY_SIZE(res->rst); i++) { |
| ret = reset_control_deassert(res->rst[i]); |
| if (ret) { |
| dev_err(dev, "reset #%d deassert failed (%d)\n", i, |
| ret); |
| return ret; |
| } |
| } |
| |
| /* |
| * Don't have a way to see if the reset has completed. |
| * Wait for some time. |
| */ |
| usleep_range(2000, 2500); |
| |
| ret = clk_prepare_enable(res->iface); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable core clock\n"); |
| goto err_clk_iface; |
| } |
| |
| ret = clk_prepare_enable(res->axi_m_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable core clock\n"); |
| goto err_clk_axi_m; |
| } |
| |
| ret = clk_prepare_enable(res->axi_s_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable axi slave clock\n"); |
| goto err_clk_axi_s; |
| } |
| |
| ret = clk_prepare_enable(res->ahb_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable ahb clock\n"); |
| goto err_clk_ahb; |
| } |
| |
| ret = clk_prepare_enable(res->aux_clk); |
| if (ret) { |
| dev_err(dev, "cannot prepare/enable aux clock\n"); |
| goto err_clk_aux; |
| } |
| |
| writel(SLV_ADDR_SPACE_SZ, |
| pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE); |
| |
| val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); |
| val &= ~BIT(0); |
| writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); |
| |
| writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); |
| |
| writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS |
| | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS | |
| AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS, |
| pcie->parf + PCIE20_PARF_SYS_CTRL); |
| writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH); |
| |
| writel(CMD_BME_VAL, pci->dbi_base + PCIE20_COMMAND_STATUS); |
| writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG); |
| writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + PCIE20_CAP_LINK_1); |
| |
| val = readl(pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES); |
| val &= ~PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT; |
| writel(val, pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES); |
| |
| writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base + |
| PCIE20_DEVICE_CONTROL2_STATUS2); |
| |
| return 0; |
| |
| err_clk_aux: |
| clk_disable_unprepare(res->ahb_clk); |
| err_clk_ahb: |
| clk_disable_unprepare(res->axi_s_clk); |
| err_clk_axi_s: |
| clk_disable_unprepare(res->axi_m_clk); |
| err_clk_axi_m: |
| clk_disable_unprepare(res->iface); |
| err_clk_iface: |
| /* |
| * Not checking for failure, will anyway return |
| * the original failure in 'ret'. |
| */ |
| for (i = 0; i < ARRAY_SIZE(res->rst); i++) |
| reset_control_assert(res->rst[i]); |
| |
| return ret; |
| } |
| |
| static int qcom_pcie_link_up(struct dw_pcie *pci) |
| { |
| u16 val = readw(pci->dbi_base + PCIE20_CAP + PCI_EXP_LNKSTA); |
| |
| return !!(val & PCI_EXP_LNKSTA_DLLLA); |
| } |
| |
| static int qcom_pcie_host_init(struct pcie_port *pp) |
| { |
| struct dw_pcie *pci = to_dw_pcie_from_pp(pp); |
| struct qcom_pcie *pcie = to_qcom_pcie(pci); |
| int ret; |
| |
| pm_runtime_get_sync(pci->dev); |
| qcom_ep_reset_assert(pcie); |
| |
| ret = pcie->ops->init(pcie); |
| if (ret) |
| return ret; |
| |
| ret = phy_power_on(pcie->phy); |
| if (ret) |
| goto err_deinit; |
| |
| if (pcie->ops->post_init) { |
| ret = pcie->ops->post_init(pcie); |
| if (ret) |
| goto err_disable_phy; |
| } |
| |
| dw_pcie_setup_rc(pp); |
| |
| if (IS_ENABLED(CONFIG_PCI_MSI)) |
| dw_pcie_msi_init(pp); |
| |
| qcom_ep_reset_deassert(pcie); |
| |
| ret = qcom_pcie_establish_link(pcie); |
| if (ret) |
| goto err; |
| |
| return 0; |
| err: |
| qcom_ep_reset_assert(pcie); |
| if (pcie->ops->post_deinit) |
| pcie->ops->post_deinit(pcie); |
| err_disable_phy: |
| phy_power_off(pcie->phy); |
| err_deinit: |
| pcie->ops->deinit(pcie); |
| pm_runtime_put(pci->dev); |
| |
| return ret; |
| } |
| |
| static int qcom_pcie_rd_own_conf(struct pcie_port *pp, int where, int size, |
| u32 *val) |
| { |
| struct dw_pcie *pci = to_dw_pcie_from_pp(pp); |
| |
| /* the device class is not reported correctly from the register */ |
| if (where == PCI_CLASS_REVISION && size == 4) { |
| *val = readl(pci->dbi_base + PCI_CLASS_REVISION); |
| *val &= 0xff; /* keep revision id */ |
| *val |= PCI_CLASS_BRIDGE_PCI << 16; |
| return PCIBIOS_SUCCESSFUL; |
| } |
| |
| return dw_pcie_read(pci->dbi_base + where, size, val); |
| } |
| |
| static const struct dw_pcie_host_ops qcom_pcie_dw_ops = { |
| .host_init = qcom_pcie_host_init, |
| .rd_own_conf = qcom_pcie_rd_own_conf, |
| }; |
| |
| /* Qcom IP rev.: 2.1.0 Synopsys IP rev.: 4.01a */ |
| static const struct qcom_pcie_ops ops_2_1_0 = { |
| .get_resources = qcom_pcie_get_resources_2_1_0, |
| .init = qcom_pcie_init_2_1_0, |
| .deinit = qcom_pcie_deinit_2_1_0, |
| .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, |
| }; |
| |
| /* Qcom IP rev.: 1.0.0 Synopsys IP rev.: 4.11a */ |
| static const struct qcom_pcie_ops ops_1_0_0 = { |
| .get_resources = qcom_pcie_get_resources_1_0_0, |
| .init = qcom_pcie_init_1_0_0, |
| .deinit = qcom_pcie_deinit_1_0_0, |
| .ltssm_enable = qcom_pcie_2_1_0_ltssm_enable, |
| }; |
| |
| /* Qcom IP rev.: 2.3.2 Synopsys IP rev.: 4.21a */ |
| static const struct qcom_pcie_ops ops_2_3_2 = { |
| .get_resources = qcom_pcie_get_resources_2_3_2, |
| .init = qcom_pcie_init_2_3_2, |
| .post_init = qcom_pcie_post_init_2_3_2, |
| .deinit = qcom_pcie_deinit_2_3_2, |
| .post_deinit = qcom_pcie_post_deinit_2_3_2, |
| .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, |
| }; |
| |
| /* Qcom IP rev.: 2.4.0 Synopsys IP rev.: 4.20a */ |
| static const struct qcom_pcie_ops ops_2_4_0 = { |
| .get_resources = qcom_pcie_get_resources_2_4_0, |
| .init = qcom_pcie_init_2_4_0, |
| .deinit = qcom_pcie_deinit_2_4_0, |
| .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, |
| }; |
| |
| /* Qcom IP rev.: 2.3.3 Synopsys IP rev.: 4.30a */ |
| static const struct qcom_pcie_ops ops_2_3_3 = { |
| .get_resources = qcom_pcie_get_resources_2_3_3, |
| .init = qcom_pcie_init_2_3_3, |
| .deinit = qcom_pcie_deinit_2_3_3, |
| .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable, |
| }; |
| |
| static const struct dw_pcie_ops dw_pcie_ops = { |
| .link_up = qcom_pcie_link_up, |
| }; |
| |
| static int qcom_pcie_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct resource *res; |
| struct pcie_port *pp; |
| struct dw_pcie *pci; |
| struct qcom_pcie *pcie; |
| int ret; |
| |
| pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL); |
| if (!pcie) |
| return -ENOMEM; |
| |
| pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL); |
| if (!pci) |
| return -ENOMEM; |
| |
| pm_runtime_enable(dev); |
| pci->dev = dev; |
| pci->ops = &dw_pcie_ops; |
| pp = &pci->pp; |
| |
| pcie->pci = pci; |
| |
| pcie->ops = of_device_get_match_data(dev); |
| |
| pcie->reset = devm_gpiod_get_optional(dev, "perst", GPIOD_OUT_LOW); |
| if (IS_ERR(pcie->reset)) |
| return PTR_ERR(pcie->reset); |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "parf"); |
| pcie->parf = devm_ioremap_resource(dev, res); |
| if (IS_ERR(pcie->parf)) |
| return PTR_ERR(pcie->parf); |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi"); |
| pci->dbi_base = devm_pci_remap_cfg_resource(dev, res); |
| if (IS_ERR(pci->dbi_base)) |
| return PTR_ERR(pci->dbi_base); |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "elbi"); |
| pcie->elbi = devm_ioremap_resource(dev, res); |
| if (IS_ERR(pcie->elbi)) |
| return PTR_ERR(pcie->elbi); |
| |
| pcie->phy = devm_phy_optional_get(dev, "pciephy"); |
| if (IS_ERR(pcie->phy)) |
| return PTR_ERR(pcie->phy); |
| |
| ret = pcie->ops->get_resources(pcie); |
| if (ret) |
| return ret; |
| |
| pp->ops = &qcom_pcie_dw_ops; |
| |
| if (IS_ENABLED(CONFIG_PCI_MSI)) { |
| pp->msi_irq = platform_get_irq_byname(pdev, "msi"); |
| if (pp->msi_irq < 0) |
| return pp->msi_irq; |
| } |
| |
| ret = phy_init(pcie->phy); |
| if (ret) { |
| pm_runtime_disable(&pdev->dev); |
| return ret; |
| } |
| |
| platform_set_drvdata(pdev, pcie); |
| |
| ret = dw_pcie_host_init(pp); |
| if (ret) { |
| dev_err(dev, "cannot initialize host\n"); |
| pm_runtime_disable(&pdev->dev); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct of_device_id qcom_pcie_match[] = { |
| { .compatible = "qcom,pcie-apq8084", .data = &ops_1_0_0 }, |
| { .compatible = "qcom,pcie-ipq8064", .data = &ops_2_1_0 }, |
| { .compatible = "qcom,pcie-apq8064", .data = &ops_2_1_0 }, |
| { .compatible = "qcom,pcie-msm8996", .data = &ops_2_3_2 }, |
| { .compatible = "qcom,pcie-ipq8074", .data = &ops_2_3_3 }, |
| { .compatible = "qcom,pcie-ipq4019", .data = &ops_2_4_0 }, |
| { } |
| }; |
| |
| static struct platform_driver qcom_pcie_driver = { |
| .probe = qcom_pcie_probe, |
| .driver = { |
| .name = "qcom-pcie", |
| .suppress_bind_attrs = true, |
| .of_match_table = qcom_pcie_match, |
| }, |
| }; |
| builtin_platform_driver(qcom_pcie_driver); |