| /* Driver for USB Mass Storage compliant devices */ |
| |
| #ifndef _USB_H_ |
| #define _USB_H_ |
| |
| #include <linux/usb.h> |
| #include <linux/usb_usual.h> |
| #include <linux/blkdev.h> |
| #include <linux/completion.h> |
| #include <linux/mutex.h> |
| #include <scsi/scsi_host.h> |
| #include "common.h" |
| |
| struct us_data; |
| struct scsi_cmnd; |
| |
| /* |
| * Unusual device list definitions |
| */ |
| |
| struct us_unusual_dev { |
| const char *vendorName; |
| const char *productName; |
| __u8 useProtocol; |
| __u8 useTransport; |
| int (*initFunction)(struct us_data *); |
| }; |
| |
| /* EnE HW Register */ |
| #define REG_CARD_STATUS 0xFF83 |
| #define REG_HW_TRAP1 0xFF89 |
| |
| /* SRB Status. Refers /usr/include/wine/wine/wnaspi32.h & SCSI sense key */ |
| #define SS_SUCCESS 0x00 /* No Sense */ |
| #define SS_NOT_READY 0x02 |
| #define SS_MEDIUM_ERR 0x03 |
| #define SS_HW_ERR 0x04 |
| #define SS_ILLEGAL_REQUEST 0x05 |
| #define SS_UNIT_ATTENTION 0x06 |
| |
| /* ENE Load FW Pattern */ |
| #define SD_INIT1_PATTERN 1 |
| #define SD_INIT2_PATTERN 2 |
| #define SD_RW_PATTERN 3 |
| #define MS_INIT_PATTERN 4 |
| #define MSP_RW_PATTERN 5 |
| #define MS_RW_PATTERN 6 |
| #define SM_INIT_PATTERN 7 |
| #define SM_RW_PATTERN 8 |
| |
| #define FDIR_WRITE 0 |
| #define FDIR_READ 1 |
| |
| struct keucr_sd_status { |
| u8 Insert:1; |
| u8 Ready:1; |
| u8 MediaChange:1; |
| u8 IsMMC:1; |
| u8 HiCapacity:1; |
| u8 HiSpeed:1; |
| u8 WtP:1; |
| u8 Reserved:1; |
| }; |
| |
| struct keucr_ms_status { |
| u8 Insert:1; |
| u8 Ready:1; |
| u8 MediaChange:1; |
| u8 IsMSPro:1; |
| u8 IsMSPHG:1; |
| u8 Reserved1:1; |
| u8 WtP:1; |
| u8 Reserved2:1; |
| }; |
| |
| struct keucr_sm_status { |
| u8 Insert:1; |
| u8 Ready:1; |
| u8 MediaChange:1; |
| u8 Reserved:3; |
| u8 WtP:1; |
| u8 IsMS:1; |
| }; |
| |
| /* SD Block Length */ |
| #define SD_BLOCK_LEN 9 /* 2^9 = 512 Bytes, |
| The HW maximum read/write data length */ |
| |
| /* Dynamic bitflag definitions (us->dflags): used in set_bit() etc. */ |
| #define US_FLIDX_URB_ACTIVE 0 /* current_urb is in use */ |
| #define US_FLIDX_SG_ACTIVE 1 /* current_sg is in use */ |
| #define US_FLIDX_ABORTING 2 /* abort is in progress */ |
| #define US_FLIDX_DISCONNECTING 3 /* disconnect in progress */ |
| #define US_FLIDX_RESETTING 4 /* device reset in progress */ |
| #define US_FLIDX_TIMED_OUT 5 /* SCSI midlayer timed out */ |
| #define US_FLIDX_DONT_SCAN 6 /* don't scan (disconnect) */ |
| |
| |
| #define USB_STOR_STRING_LEN 32 |
| |
| /* |
| * We provide a DMA-mapped I/O buffer for use with small USB transfers. |
| * It turns out that CB[I] needs a 12-byte buffer and Bulk-only needs a |
| * 31-byte buffer. But Freecom needs a 64-byte buffer, so that's the |
| * size we'll allocate. |
| */ |
| |
| #define US_IOBUF_SIZE 64 /* Size of the DMA-mapped I/O buffer */ |
| #define US_SENSE_SIZE 18 /* Size of the autosense data buffer */ |
| |
| typedef int (*trans_cmnd)(struct scsi_cmnd *, struct us_data *); |
| typedef int (*trans_reset)(struct us_data *); |
| typedef void (*proto_cmnd)(struct scsi_cmnd *, struct us_data *); |
| typedef void (*extra_data_destructor)(void *); /* extra data destructor */ |
| typedef void (*pm_hook)(struct us_data *, int); /* power management hook */ |
| |
| #define US_SUSPEND 0 |
| #define US_RESUME 1 |
| |
| /* we allocate one of these for every device that we remember */ |
| struct us_data { |
| /* The device we're working with |
| * It's important to note: |
| * (o) you must hold dev_mutex to change pusb_dev |
| */ |
| struct mutex dev_mutex; /* protect pusb_dev */ |
| struct usb_device *pusb_dev; /* this usb_device */ |
| struct usb_interface *pusb_intf; /* this interface */ |
| struct us_unusual_dev *unusual_dev; /* device-filter entry */ |
| unsigned long fflags; /* fixed flags from filter */ |
| unsigned long dflags; /* dynamic atomic bitflags */ |
| unsigned int send_bulk_pipe; /* cached pipe values */ |
| unsigned int recv_bulk_pipe; |
| unsigned int send_ctrl_pipe; |
| unsigned int recv_ctrl_pipe; |
| unsigned int recv_intr_pipe; |
| |
| /* information about the device */ |
| char *transport_name; |
| char *protocol_name; |
| __le32 bcs_signature; |
| u8 subclass; |
| u8 protocol; |
| u8 max_lun; |
| |
| u8 ifnum; /* interface number */ |
| u8 ep_bInterval; /* interrupt interval */ |
| |
| /* function pointers for this device */ |
| trans_cmnd transport; /* transport function */ |
| trans_reset transport_reset; /* transport device reset */ |
| proto_cmnd proto_handler; /* protocol handler */ |
| |
| /* SCSI interfaces */ |
| struct scsi_cmnd *srb; /* current srb */ |
| unsigned int tag; /* current dCBWTag */ |
| |
| /* control and bulk communications data */ |
| struct urb *current_urb; /* USB requests */ |
| struct usb_ctrlrequest *cr; /* control requests */ |
| struct usb_sg_request current_sg; /* scatter-gather req. */ |
| unsigned char *iobuf; /* I/O buffer */ |
| unsigned char *sensebuf; /* sense data buffer */ |
| dma_addr_t cr_dma; /* buffer DMA addresses */ |
| dma_addr_t iobuf_dma; |
| struct task_struct *ctl_thread; /* the control thread */ |
| |
| /* mutual exclusion and synchronization structures */ |
| struct completion cmnd_ready; /* to sleep thread on */ |
| struct completion notify; /* thread begin/end */ |
| wait_queue_head_t delay_wait; /* wait during scan, reset */ |
| struct completion scanning_done; /* wait for scan thread */ |
| |
| /* subdriver information */ |
| void *extra; /* Any extra data */ |
| extra_data_destructor extra_destructor;/* extra data destructor */ |
| #ifdef CONFIG_PM |
| pm_hook suspend_resume_hook; |
| #endif |
| /* for 6250 code */ |
| struct keucr_sd_status SD_Status; |
| struct keucr_ms_status MS_Status; |
| struct keucr_sm_status SM_Status; |
| |
| /* ----- SD Control Data ---------------- */ |
| /* SD_REGISTER SD_Regs; */ |
| u16 SD_Block_Mult; |
| u8 SD_READ_BL_LEN; |
| u16 SD_C_SIZE; |
| u8 SD_C_SIZE_MULT; |
| |
| /* SD/MMC New spec. */ |
| u8 SD_SPEC_VER; |
| u8 SD_CSD_VER; |
| u8 SD20_HIGH_CAPACITY; |
| u32 HC_C_SIZE; |
| u8 MMC_SPEC_VER; |
| u8 MMC_BusWidth; |
| u8 MMC_HIGH_CAPACITY; |
| |
| /* ----- MS Control Data ---------------- */ |
| bool MS_SWWP; |
| u32 MSP_TotalBlock; |
| /* MS_LibControl MS_Lib; */ |
| bool MS_IsRWPage; |
| u16 MS_Model; |
| |
| /* ----- SM Control Data ---------------- */ |
| u8 SM_DeviceID; |
| u8 SM_CardID; |
| |
| u8 *testbuf; |
| u8 BIN_FLAG; |
| u32 bl_num; |
| int SrbStatus; |
| |
| /* ------Power Managerment --------------- */ |
| bool Power_IsResum; |
| }; |
| |
| /* Convert between us_data and the corresponding Scsi_Host */ |
| static inline struct Scsi_Host *us_to_host(struct us_data *us) |
| { |
| return container_of((void *) us, struct Scsi_Host, hostdata); |
| } |
| static inline struct us_data *host_to_us(struct Scsi_Host *host) |
| { |
| return (struct us_data *) host->hostdata; |
| } |
| |
| /* Function to fill an inquiry response. See usb.c for details */ |
| extern void fill_inquiry_response(struct us_data *us, |
| unsigned char *data, unsigned int data_len); |
| |
| /* The scsi_lock() and scsi_unlock() macros protect the sm_state and the |
| * single queue element srb for write access */ |
| #define scsi_unlock(host) spin_unlock_irq(host->host_lock) |
| #define scsi_lock(host) spin_lock_irq(host->host_lock) |
| |
| #endif |
