blob: 29ec343872466e49a310ad740b67fe2f9a9603d0 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
#include <linux/clk.h>
#include <linux/console.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/qcom-geni-se.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
/* UART specific GENI registers */
#define SE_UART_LOOPBACK_CFG 0x22c
#define SE_UART_TX_TRANS_CFG 0x25c
#define SE_UART_TX_WORD_LEN 0x268
#define SE_UART_TX_STOP_BIT_LEN 0x26c
#define SE_UART_TX_TRANS_LEN 0x270
#define SE_UART_RX_TRANS_CFG 0x280
#define SE_UART_RX_WORD_LEN 0x28c
#define SE_UART_RX_STALE_CNT 0x294
#define SE_UART_TX_PARITY_CFG 0x2a4
#define SE_UART_RX_PARITY_CFG 0x2a8
#define SE_UART_MANUAL_RFR 0x2ac
/* SE_UART_TRANS_CFG */
#define UART_TX_PAR_EN BIT(0)
#define UART_CTS_MASK BIT(1)
/* SE_UART_TX_WORD_LEN */
#define TX_WORD_LEN_MSK GENMASK(9, 0)
/* SE_UART_TX_STOP_BIT_LEN */
#define TX_STOP_BIT_LEN_MSK GENMASK(23, 0)
#define TX_STOP_BIT_LEN_1 0
#define TX_STOP_BIT_LEN_1_5 1
#define TX_STOP_BIT_LEN_2 2
/* SE_UART_TX_TRANS_LEN */
#define TX_TRANS_LEN_MSK GENMASK(23, 0)
/* SE_UART_RX_TRANS_CFG */
#define UART_RX_INS_STATUS_BIT BIT(2)
#define UART_RX_PAR_EN BIT(3)
/* SE_UART_RX_WORD_LEN */
#define RX_WORD_LEN_MASK GENMASK(9, 0)
/* SE_UART_RX_STALE_CNT */
#define RX_STALE_CNT GENMASK(23, 0)
/* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */
#define PAR_CALC_EN BIT(0)
#define PAR_MODE_MSK GENMASK(2, 1)
#define PAR_MODE_SHFT 1
#define PAR_EVEN 0x00
#define PAR_ODD 0x01
#define PAR_SPACE 0x10
#define PAR_MARK 0x11
/* SE_UART_MANUAL_RFR register fields */
#define UART_MANUAL_RFR_EN BIT(31)
#define UART_RFR_NOT_READY BIT(1)
#define UART_RFR_READY BIT(0)
/* UART M_CMD OP codes */
#define UART_START_TX 0x1
#define UART_START_BREAK 0x4
#define UART_STOP_BREAK 0x5
/* UART S_CMD OP codes */
#define UART_START_READ 0x1
#define UART_PARAM 0x1
#define UART_OVERSAMPLING 32
#define STALE_TIMEOUT 16
#define DEFAULT_BITS_PER_CHAR 10
#define GENI_UART_CONS_PORTS 1
#define GENI_UART_PORTS 3
#define DEF_FIFO_DEPTH_WORDS 16
#define DEF_TX_WM 2
#define DEF_FIFO_WIDTH_BITS 32
#define UART_CONSOLE_RX_WM 2
#define MAX_LOOPBACK_CFG 3
#ifdef CONFIG_CONSOLE_POLL
#define RX_BYTES_PW 1
#else
#define RX_BYTES_PW 4
#endif
struct qcom_geni_serial_port {
struct uart_port uport;
struct geni_se se;
char name[20];
u32 tx_fifo_depth;
u32 tx_fifo_width;
u32 rx_fifo_depth;
u32 tx_wm;
u32 rx_wm;
u32 rx_rfr;
enum geni_se_xfer_mode xfer_mode;
bool setup;
int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop);
unsigned int baud;
unsigned int tx_bytes_pw;
unsigned int rx_bytes_pw;
u32 *rx_fifo;
u32 loopback;
bool brk;
};
static const struct uart_ops qcom_geni_console_pops;
static const struct uart_ops qcom_geni_uart_pops;
static struct uart_driver qcom_geni_console_driver;
static struct uart_driver qcom_geni_uart_driver;
static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop);
static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop);
static unsigned int qcom_geni_serial_tx_empty(struct uart_port *port);
static void qcom_geni_serial_stop_rx(struct uart_port *uport);
static const unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200,
32000000, 48000000, 64000000, 80000000,
96000000, 100000000, 102400000,
112000000, 120000000, 128000000};
#define to_dev_port(ptr, member) \
container_of(ptr, struct qcom_geni_serial_port, member)
static struct qcom_geni_serial_port qcom_geni_uart_ports[GENI_UART_PORTS] = {
[0] = {
.uport = {
.iotype = UPIO_MEM,
.ops = &qcom_geni_uart_pops,
.flags = UPF_BOOT_AUTOCONF,
.line = 0,
},
},
[1] = {
.uport = {
.iotype = UPIO_MEM,
.ops = &qcom_geni_uart_pops,
.flags = UPF_BOOT_AUTOCONF,
.line = 1,
},
},
[2] = {
.uport = {
.iotype = UPIO_MEM,
.ops = &qcom_geni_uart_pops,
.flags = UPF_BOOT_AUTOCONF,
.line = 2,
},
},
};
static ssize_t loopback_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct platform_device *pdev = to_platform_device(dev);
struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
return snprintf(buf, sizeof(u32), "%d\n", port->loopback);
}
static ssize_t loopback_store(struct device *dev,
struct device_attribute *attr, const char *buf,
size_t size)
{
struct platform_device *pdev = to_platform_device(dev);
struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
u32 loopback;
if (kstrtoint(buf, 0, &loopback) || loopback > MAX_LOOPBACK_CFG) {
dev_err(dev, "Invalid input\n");
return -EINVAL;
}
port->loopback = loopback;
return size;
}
static DEVICE_ATTR_RW(loopback);
static struct qcom_geni_serial_port qcom_geni_console_port = {
.uport = {
.iotype = UPIO_MEM,
.ops = &qcom_geni_console_pops,
.flags = UPF_BOOT_AUTOCONF,
.line = 0,
},
};
static int qcom_geni_serial_request_port(struct uart_port *uport)
{
struct platform_device *pdev = to_platform_device(uport->dev);
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
struct resource *res;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
uport->membase = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(uport->membase))
return PTR_ERR(uport->membase);
port->se.base = uport->membase;
return 0;
}
static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags)
{
if (cfg_flags & UART_CONFIG_TYPE) {
uport->type = PORT_MSM;
qcom_geni_serial_request_port(uport);
}
}
static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport)
{
unsigned int mctrl = TIOCM_DSR | TIOCM_CAR;
u32 geni_ios;
if (uart_console(uport) || !uart_cts_enabled(uport)) {
mctrl |= TIOCM_CTS;
} else {
geni_ios = readl_relaxed(uport->membase + SE_GENI_IOS);
if (!(geni_ios & IO2_DATA_IN))
mctrl |= TIOCM_CTS;
}
return mctrl;
}
static void qcom_geni_serial_set_mctrl(struct uart_port *uport,
unsigned int mctrl)
{
u32 uart_manual_rfr = 0;
if (uart_console(uport) || !uart_cts_enabled(uport))
return;
if (!(mctrl & TIOCM_RTS))
uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY;
writel_relaxed(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR);
}
static const char *qcom_geni_serial_get_type(struct uart_port *uport)
{
return "MSM";
}
static struct qcom_geni_serial_port *get_port_from_line(int line, bool console)
{
struct qcom_geni_serial_port *port;
int nr_ports = console ? GENI_UART_CONS_PORTS : GENI_UART_PORTS;
if (line < 0 || line >= nr_ports)
return ERR_PTR(-ENXIO);
port = console ? &qcom_geni_console_port : &qcom_geni_uart_ports[line];
return port;
}
static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
int offset, int field, bool set)
{
u32 reg;
struct qcom_geni_serial_port *port;
unsigned int baud;
unsigned int fifo_bits;
unsigned long timeout_us = 20000;
/* Ensure polling is not re-ordered before the prior writes/reads */
mb();
if (uport->private_data) {
port = to_dev_port(uport, uport);
baud = port->baud;
if (!baud)
baud = 115200;
fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
/*
* Total polling iterations based on FIFO worth of bytes to be
* sent at current baud. Add a little fluff to the wait.
*/
timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
}
/*
* Use custom implementation instead of readl_poll_atomic since ktimer
* is not ready at the time of early console.
*/
timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10;
while (timeout_us) {
reg = readl_relaxed(uport->membase + offset);
if ((bool)(reg & field) == set)
return true;
udelay(10);
timeout_us -= 10;
}
return false;
}
static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
{
u32 m_cmd;
writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
m_cmd = UART_START_TX << M_OPCODE_SHFT;
writel(m_cmd, uport->membase + SE_GENI_M_CMD0);
}
static void qcom_geni_serial_poll_tx_done(struct uart_port *uport)
{
int done;
u32 irq_clear = M_CMD_DONE_EN;
done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_DONE_EN, true);
if (!done) {
writel_relaxed(M_GENI_CMD_ABORT, uport->membase +
SE_GENI_M_CMD_CTRL_REG);
irq_clear |= M_CMD_ABORT_EN;
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
}
writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
static void qcom_geni_serial_abort_rx(struct uart_port *uport)
{
u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN;
writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG);
qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
S_GENI_CMD_ABORT, false);
writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
}
#ifdef CONFIG_CONSOLE_POLL
static int qcom_geni_serial_get_char(struct uart_port *uport)
{
u32 rx_fifo;
u32 status;
status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
/*
* Ensure the writes to clear interrupts is not re-ordered after
* reading the data.
*/
mb();
status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
if (!(status & RX_FIFO_WC_MSK))
return NO_POLL_CHAR;
rx_fifo = readl(uport->membase + SE_GENI_RX_FIFOn);
return rx_fifo & 0xff;
}
static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
unsigned char c)
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG);
qcom_geni_serial_setup_tx(uport, 1);
WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_TX_FIFO_WATERMARK_EN, true));
writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn);
writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
qcom_geni_serial_poll_tx_done(uport);
}
#endif
#ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE
static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch)
{
writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn);
}
static void
__qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
unsigned int count)
{
int i;
u32 bytes_to_send = count;
for (i = 0; i < count; i++) {
/*
* uart_console_write() adds a carriage return for each newline.
* Account for additional bytes to be written.
*/
if (s[i] == '\n')
bytes_to_send++;
}
writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
qcom_geni_serial_setup_tx(uport, bytes_to_send);
for (i = 0; i < count; ) {
size_t chars_to_write = 0;
size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM;
/*
* If the WM bit never set, then the Tx state machine is not
* in a valid state, so break, cancel/abort any existing
* command. Unfortunately the current data being written is
* lost.
*/
if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_TX_FIFO_WATERMARK_EN, true))
break;
chars_to_write = min_t(size_t, count - i, avail / 2);
uart_console_write(uport, s + i, chars_to_write,
qcom_geni_serial_wr_char);
writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
i += chars_to_write;
}
qcom_geni_serial_poll_tx_done(uport);
}
static void qcom_geni_serial_console_write(struct console *co, const char *s,
unsigned int count)
{
struct uart_port *uport;
struct qcom_geni_serial_port *port;
bool locked = true;
unsigned long flags;
WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS);
port = get_port_from_line(co->index, true);
if (IS_ERR(port))
return;
uport = &port->uport;
if (oops_in_progress)
locked = spin_trylock_irqsave(&uport->lock, flags);
else
spin_lock_irqsave(&uport->lock, flags);
/* Cancel the current write to log the fault */
if (!locked) {
geni_se_cancel_m_cmd(&port->se);
if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_CANCEL_EN, true)) {
geni_se_abort_m_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
writel_relaxed(M_CMD_ABORT_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
}
writel_relaxed(M_CMD_CANCEL_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
}
__qcom_geni_serial_console_write(uport, s, count);
if (locked)
spin_unlock_irqrestore(&uport->lock, flags);
}
static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop)
{
u32 i;
unsigned char buf[sizeof(u32)];
struct tty_port *tport;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
tport = &uport->state->port;
for (i = 0; i < bytes; ) {
int c;
int chunk = min_t(int, bytes - i, port->rx_bytes_pw);
ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, buf, 1);
i += chunk;
if (drop)
continue;
for (c = 0; c < chunk; c++) {
int sysrq;
uport->icount.rx++;
if (port->brk && buf[c] == 0) {
port->brk = false;
if (uart_handle_break(uport))
continue;
}
sysrq = uart_handle_sysrq_char(uport, buf[c]);
if (!sysrq)
tty_insert_flip_char(tport, buf[c], TTY_NORMAL);
}
}
if (!drop)
tty_flip_buffer_push(tport);
return 0;
}
#else
static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop)
{
return -EPERM;
}
#endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */
static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop)
{
unsigned char *buf;
struct tty_port *tport;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
u32 num_bytes_pw = port->tx_fifo_width / BITS_PER_BYTE;
u32 words = ALIGN(bytes, num_bytes_pw) / num_bytes_pw;
int ret;
tport = &uport->state->port;
ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, port->rx_fifo, words);
if (drop)
return 0;
buf = (unsigned char *)port->rx_fifo;
ret = tty_insert_flip_string(tport, buf, bytes);
if (ret != bytes) {
dev_err(uport->dev, "%s:Unable to push data ret %d_bytes %d\n",
__func__, ret, bytes);
WARN_ON_ONCE(1);
}
uport->icount.rx += ret;
tty_flip_buffer_push(tport);
return ret;
}
static void qcom_geni_serial_start_tx(struct uart_port *uport)
{
u32 irq_en;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
u32 status;
if (port->xfer_mode == GENI_SE_FIFO) {
/*
* readl ensures reading & writing of IRQ_EN register
* is not re-ordered before checking the status of the
* Serial Engine.
*/
status = readl(uport->membase + SE_GENI_STATUS);
if (status & M_GENI_CMD_ACTIVE)
return;
if (!qcom_geni_serial_tx_empty(uport))
return;
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN;
writel_relaxed(port->tx_wm, uport->membase +
SE_GENI_TX_WATERMARK_REG);
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
}
static void qcom_geni_serial_stop_tx(struct uart_port *uport)
{
u32 irq_en;
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~M_CMD_DONE_EN;
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en &= ~M_TX_FIFO_WATERMARK_EN;
writel_relaxed(0, uport->membase +
SE_GENI_TX_WATERMARK_REG);
}
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
/* Possible stop tx is called multiple times. */
if (!(status & M_GENI_CMD_ACTIVE))
return;
/*
* Ensure cancel command write is not re-ordered before checking
* the status of the Primary Sequencer.
*/
mb();
geni_se_cancel_m_cmd(&port->se);
if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_CANCEL_EN, true)) {
geni_se_abort_m_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
writel_relaxed(M_CMD_ABORT_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
}
writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
static void qcom_geni_serial_start_rx(struct uart_port *uport)
{
u32 irq_en;
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
if (status & S_GENI_CMD_ACTIVE)
qcom_geni_serial_stop_rx(uport);
/*
* Ensure setup command write is not re-ordered before checking
* the status of the Secondary Sequencer.
*/
mb();
geni_se_setup_s_cmd(&port->se, UART_START_READ, 0);
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN;
writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN;
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
}
static void qcom_geni_serial_stop_rx(struct uart_port *uport)
{
u32 irq_en;
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
u32 irq_clear = S_CMD_DONE_EN;
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN);
writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN);
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
/* Possible stop rx is called multiple times. */
if (!(status & S_GENI_CMD_ACTIVE))
return;
/*
* Ensure cancel command write is not re-ordered before checking
* the status of the Secondary Sequencer.
*/
mb();
geni_se_cancel_s_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
S_GENI_CMD_CANCEL, false);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
if (status & S_GENI_CMD_ACTIVE)
qcom_geni_serial_abort_rx(uport);
}
static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop)
{
u32 status;
u32 word_cnt;
u32 last_word_byte_cnt;
u32 last_word_partial;
u32 total_bytes;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
word_cnt = status & RX_FIFO_WC_MSK;
last_word_partial = status & RX_LAST;
last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >>
RX_LAST_BYTE_VALID_SHFT;
if (!word_cnt)
return;
total_bytes = port->rx_bytes_pw * (word_cnt - 1);
if (last_word_partial && last_word_byte_cnt)
total_bytes += last_word_byte_cnt;
else
total_bytes += port->rx_bytes_pw;
port->handle_rx(uport, total_bytes, drop);
}
static void qcom_geni_serial_handle_tx(struct uart_port *uport)
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
struct circ_buf *xmit = &uport->state->xmit;
size_t avail;
size_t remaining;
int i;
u32 status;
unsigned int chunk;
int tail;
u32 irq_en;
chunk = uart_circ_chars_pending(xmit);
status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
/* Both FIFO and framework buffer are drained */
if (!chunk && !status) {
qcom_geni_serial_stop_tx(uport);
goto out_write_wakeup;
}
if (!uart_console(uport)) {
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~(M_TX_FIFO_WATERMARK_EN);
writel_relaxed(0, uport->membase + SE_GENI_TX_WATERMARK_REG);
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
avail = (port->tx_fifo_depth - port->tx_wm) * port->tx_bytes_pw;
tail = xmit->tail;
chunk = min3((size_t)chunk, (size_t)(UART_XMIT_SIZE - tail), avail);
if (!chunk)
goto out_write_wakeup;
qcom_geni_serial_setup_tx(uport, chunk);
remaining = chunk;
for (i = 0; i < chunk; ) {
unsigned int tx_bytes;
u8 buf[sizeof(u32)];
int c;
memset(buf, 0, ARRAY_SIZE(buf));
tx_bytes = min_t(size_t, remaining, port->tx_bytes_pw);
for (c = 0; c < tx_bytes ; c++)
buf[c] = xmit->buf[tail + c];
iowrite32_rep(uport->membase + SE_GENI_TX_FIFOn, buf, 1);
i += tx_bytes;
tail += tx_bytes;
uport->icount.tx += tx_bytes;
remaining -= tx_bytes;
}
xmit->tail = tail & (UART_XMIT_SIZE - 1);
if (uart_console(uport))
qcom_geni_serial_poll_tx_done(uport);
out_write_wakeup:
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(uport);
}
static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
{
unsigned int m_irq_status;
unsigned int s_irq_status;
struct uart_port *uport = dev;
unsigned long flags;
unsigned int m_irq_en;
bool drop_rx = false;
struct tty_port *tport = &uport->state->port;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
if (uport->suspended)
return IRQ_NONE;
spin_lock_irqsave(&uport->lock, flags);
m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN))
goto out_unlock;
if (s_irq_status & S_RX_FIFO_WR_ERR_EN) {
uport->icount.overrun++;
tty_insert_flip_char(tport, 0, TTY_OVERRUN);
}
if (m_irq_status & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN) &&
m_irq_en & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN))
qcom_geni_serial_handle_tx(uport);
if (s_irq_status & S_GP_IRQ_0_EN || s_irq_status & S_GP_IRQ_1_EN) {
if (s_irq_status & S_GP_IRQ_0_EN)
uport->icount.parity++;
drop_rx = true;
} else if (s_irq_status & S_GP_IRQ_2_EN ||
s_irq_status & S_GP_IRQ_3_EN) {
uport->icount.brk++;
port->brk = true;
}
if (s_irq_status & S_RX_FIFO_WATERMARK_EN ||
s_irq_status & S_RX_FIFO_LAST_EN)
qcom_geni_serial_handle_rx(uport, drop_rx);
out_unlock:
spin_unlock_irqrestore(&uport->lock, flags);
return IRQ_HANDLED;
}
static void get_tx_fifo_size(struct qcom_geni_serial_port *port)
{
struct uart_port *uport;
uport = &port->uport;
port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se);
port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se);
port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se);
uport->fifosize =
(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;
}
static void set_rfr_wm(struct qcom_geni_serial_port *port)
{
/*
* Set RFR (Flow off) to FIFO_DEPTH - 2.
* RX WM level at 10% RX_FIFO_DEPTH.
* TX WM level at 10% TX_FIFO_DEPTH.
*/
port->rx_rfr = port->rx_fifo_depth - 2;
port->rx_wm = UART_CONSOLE_RX_WM;
port->tx_wm = DEF_TX_WM;
}
static void qcom_geni_serial_shutdown(struct uart_port *uport)
{
unsigned long flags;
/* Stop the console before stopping the current tx */
if (uart_console(uport))
console_stop(uport->cons);
free_irq(uport->irq, uport);
spin_lock_irqsave(&uport->lock, flags);
qcom_geni_serial_stop_tx(uport);
qcom_geni_serial_stop_rx(uport);
spin_unlock_irqrestore(&uport->lock, flags);
}
static int qcom_geni_serial_port_setup(struct uart_port *uport)
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
unsigned int rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
set_rfr_wm(port);
writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
/*
* Make an unconditional cancel on the main sequencer to reset
* it else we could end up in data loss scenarios.
*/
port->xfer_mode = GENI_SE_FIFO;
if (uart_console(uport))
qcom_geni_serial_poll_tx_done(uport);
geni_se_config_packing(&port->se, BITS_PER_BYTE, port->tx_bytes_pw,
false, true, false);
geni_se_config_packing(&port->se, BITS_PER_BYTE, port->rx_bytes_pw,
false, false, true);
geni_se_init(&port->se, port->rx_wm, port->rx_rfr);
geni_se_select_mode(&port->se, port->xfer_mode);
if (!uart_console(uport)) {
port->rx_fifo = devm_kzalloc(uport->dev,
port->rx_fifo_depth * sizeof(u32), GFP_KERNEL);
if (!port->rx_fifo)
return -ENOMEM;
}
port->setup = true;
return 0;
}
static int qcom_geni_serial_startup(struct uart_port *uport)
{
int ret;
u32 proto;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
scnprintf(port->name, sizeof(port->name),
"qcom_serial_%s%d",
(uart_console(uport) ? "console" : "uart"), uport->line);
if (!uart_console(uport)) {
port->tx_bytes_pw = 4;
port->rx_bytes_pw = RX_BYTES_PW;
}
proto = geni_se_read_proto(&port->se);
if (proto != GENI_SE_UART) {
dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto);
return -ENXIO;
}
get_tx_fifo_size(port);
if (!port->setup) {
ret = qcom_geni_serial_port_setup(uport);
if (ret)
return ret;
}
ret = request_irq(uport->irq, qcom_geni_serial_isr, IRQF_TRIGGER_HIGH,
port->name, uport);
if (ret)
dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret);
return ret;
}
static unsigned long get_clk_cfg(unsigned long clk_freq)
{
int i;
for (i = 0; i < ARRAY_SIZE(root_freq); i++) {
if (!(root_freq[i] % clk_freq))
return root_freq[i];
}
return 0;
}
static unsigned long get_clk_div_rate(unsigned int baud, unsigned int *clk_div)
{
unsigned long ser_clk;
unsigned long desired_clk;
desired_clk = baud * UART_OVERSAMPLING;
ser_clk = get_clk_cfg(desired_clk);
if (!ser_clk) {
pr_err("%s: Can't find matching DFS entry for baud %d\n",
__func__, baud);
return ser_clk;
}
*clk_div = ser_clk / desired_clk;
return ser_clk;
}
static void qcom_geni_serial_set_termios(struct uart_port *uport,
struct ktermios *termios, struct ktermios *old)
{
unsigned int baud;
unsigned int bits_per_char;
unsigned int tx_trans_cfg;
unsigned int tx_parity_cfg;
unsigned int rx_trans_cfg;
unsigned int rx_parity_cfg;
unsigned int stop_bit_len;
unsigned int clk_div;
unsigned long ser_clk_cfg;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
unsigned long clk_rate;
qcom_geni_serial_stop_rx(uport);
/* baud rate */
baud = uart_get_baud_rate(uport, termios, old, 300, 4000000);
port->baud = baud;
clk_rate = get_clk_div_rate(baud, &clk_div);
if (!clk_rate)
goto out_restart_rx;
uport->uartclk = clk_rate;
clk_set_rate(port->se.clk, clk_rate);
ser_clk_cfg = SER_CLK_EN;
ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
/* parity */
tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG);
tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG);
rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG);
rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG);
if (termios->c_cflag & PARENB) {
tx_trans_cfg |= UART_TX_PAR_EN;
rx_trans_cfg |= UART_RX_PAR_EN;
tx_parity_cfg |= PAR_CALC_EN;
rx_parity_cfg |= PAR_CALC_EN;
if (termios->c_cflag & PARODD) {
tx_parity_cfg |= PAR_ODD;
rx_parity_cfg |= PAR_ODD;
} else if (termios->c_cflag & CMSPAR) {
tx_parity_cfg |= PAR_SPACE;
rx_parity_cfg |= PAR_SPACE;
} else {
tx_parity_cfg |= PAR_EVEN;
rx_parity_cfg |= PAR_EVEN;
}
} else {
tx_trans_cfg &= ~UART_TX_PAR_EN;
rx_trans_cfg &= ~UART_RX_PAR_EN;
tx_parity_cfg &= ~PAR_CALC_EN;
rx_parity_cfg &= ~PAR_CALC_EN;
}
/* bits per char */
switch (termios->c_cflag & CSIZE) {
case CS5:
bits_per_char = 5;
break;
case CS6:
bits_per_char = 6;
break;
case CS7:
bits_per_char = 7;
break;
case CS8:
default:
bits_per_char = 8;
break;
}
/* stop bits */
if (termios->c_cflag & CSTOPB)
stop_bit_len = TX_STOP_BIT_LEN_2;
else
stop_bit_len = TX_STOP_BIT_LEN_1;
/* flow control, clear the CTS_MASK bit if using flow control. */
if (termios->c_cflag & CRTSCTS)
tx_trans_cfg &= ~UART_CTS_MASK;
else
tx_trans_cfg |= UART_CTS_MASK;
if (baud)
uart_update_timeout(uport, termios->c_cflag, baud);
if (!uart_console(uport))
writel_relaxed(port->loopback,
uport->membase + SE_UART_LOOPBACK_CFG);
writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
out_restart_rx:
qcom_geni_serial_start_rx(uport);
}
static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport)
{
return !readl(uport->membase + SE_GENI_TX_FIFO_STATUS);
}
#ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE
static int __init qcom_geni_console_setup(struct console *co, char *options)
{
struct uart_port *uport;
struct qcom_geni_serial_port *port;
int baud;
int bits = 8;
int parity = 'n';
int flow = 'n';
if (co->index >= GENI_UART_CONS_PORTS || co->index < 0)
return -ENXIO;
port = get_port_from_line(co->index, true);
if (IS_ERR(port)) {
pr_err("Invalid line %d\n", co->index);
return PTR_ERR(port);
}
uport = &port->uport;
if (unlikely(!uport->membase))
return -ENXIO;
if (geni_se_resources_on(&port->se)) {
dev_err(port->se.dev, "Error turning on resources\n");
return -ENXIO;
}
if (unlikely(geni_se_read_proto(&port->se) != GENI_SE_UART)) {
geni_se_resources_off(&port->se);
return -ENXIO;
}
if (!port->setup) {
port->tx_bytes_pw = 1;
port->rx_bytes_pw = RX_BYTES_PW;
qcom_geni_serial_stop_rx(uport);
qcom_geni_serial_port_setup(uport);
}
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
return uart_set_options(uport, co, baud, parity, bits, flow);
}
static void qcom_geni_serial_earlycon_write(struct console *con,
const char *s, unsigned int n)
{
struct earlycon_device *dev = con->data;
__qcom_geni_serial_console_write(&dev->port, s, n);
}
static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev,
const char *opt)
{
struct uart_port *uport = &dev->port;
u32 tx_trans_cfg;
u32 tx_parity_cfg = 0; /* Disable Tx Parity */
u32 rx_trans_cfg = 0;
u32 rx_parity_cfg = 0; /* Disable Rx Parity */
u32 stop_bit_len = 0; /* Default stop bit length - 1 bit */
u32 bits_per_char;
struct geni_se se;
if (!uport->membase)
return -EINVAL;
memset(&se, 0, sizeof(se));
se.base = uport->membase;
if (geni_se_read_proto(&se) != GENI_SE_UART)
return -ENXIO;
/*
* Ignore Flow control.
* n = 8.
*/
tx_trans_cfg = UART_CTS_MASK;
bits_per_char = BITS_PER_BYTE;
/*
* Make an unconditional cancel on the main sequencer to reset
* it else we could end up in data loss scenarios.
*/
qcom_geni_serial_poll_tx_done(uport);
qcom_geni_serial_abort_rx(uport);
geni_se_config_packing(&se, BITS_PER_BYTE, 1, false, true, false);
geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2);
geni_se_select_mode(&se, GENI_SE_FIFO);
writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
dev->con->write = qcom_geni_serial_earlycon_write;
dev->con->setup = NULL;
return 0;
}
OF_EARLYCON_DECLARE(qcom_geni, "qcom,geni-debug-uart",
qcom_geni_serial_earlycon_setup);
static int __init console_register(struct uart_driver *drv)
{
return uart_register_driver(drv);
}
static void console_unregister(struct uart_driver *drv)
{
uart_unregister_driver(drv);
}
static struct console cons_ops = {
.name = "ttyMSM",
.write = qcom_geni_serial_console_write,
.device = uart_console_device,
.setup = qcom_geni_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &qcom_geni_console_driver,
};
static struct uart_driver qcom_geni_console_driver = {
.owner = THIS_MODULE,
.driver_name = "qcom_geni_console",
.dev_name = "ttyMSM",
.nr = GENI_UART_CONS_PORTS,
.cons = &cons_ops,
};
#else
static int console_register(struct uart_driver *drv)
{
return 0;
}
static void console_unregister(struct uart_driver *drv)
{
}
#endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */
static struct uart_driver qcom_geni_uart_driver = {
.owner = THIS_MODULE,
.driver_name = "qcom_geni_uart",
.dev_name = "ttyHS",
.nr = GENI_UART_PORTS,
};
static void qcom_geni_serial_pm(struct uart_port *uport,
unsigned int new_state, unsigned int old_state)
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF)
geni_se_resources_on(&port->se);
else if (!uart_console(uport) && (new_state == UART_PM_STATE_ON &&
old_state == UART_PM_STATE_UNDEFINED))
geni_se_resources_on(&port->se);
else if (new_state == UART_PM_STATE_OFF &&
old_state == UART_PM_STATE_ON)
geni_se_resources_off(&port->se);
}
static const struct uart_ops qcom_geni_console_pops = {
.tx_empty = qcom_geni_serial_tx_empty,
.stop_tx = qcom_geni_serial_stop_tx,
.start_tx = qcom_geni_serial_start_tx,
.stop_rx = qcom_geni_serial_stop_rx,
.set_termios = qcom_geni_serial_set_termios,
.startup = qcom_geni_serial_startup,
.request_port = qcom_geni_serial_request_port,
.config_port = qcom_geni_serial_config_port,
.shutdown = qcom_geni_serial_shutdown,
.type = qcom_geni_serial_get_type,
.set_mctrl = qcom_geni_serial_set_mctrl,
.get_mctrl = qcom_geni_serial_get_mctrl,
#ifdef CONFIG_CONSOLE_POLL
.poll_get_char = qcom_geni_serial_get_char,
.poll_put_char = qcom_geni_serial_poll_put_char,
#endif
.pm = qcom_geni_serial_pm,
};
static const struct uart_ops qcom_geni_uart_pops = {
.tx_empty = qcom_geni_serial_tx_empty,
.stop_tx = qcom_geni_serial_stop_tx,
.start_tx = qcom_geni_serial_start_tx,
.stop_rx = qcom_geni_serial_stop_rx,
.set_termios = qcom_geni_serial_set_termios,
.startup = qcom_geni_serial_startup,
.request_port = qcom_geni_serial_request_port,
.config_port = qcom_geni_serial_config_port,
.shutdown = qcom_geni_serial_shutdown,
.type = qcom_geni_serial_get_type,
.set_mctrl = qcom_geni_serial_set_mctrl,
.get_mctrl = qcom_geni_serial_get_mctrl,
.pm = qcom_geni_serial_pm,
};
static int qcom_geni_serial_probe(struct platform_device *pdev)
{
int ret = 0;
int line = -1;
struct qcom_geni_serial_port *port;
struct uart_port *uport;
struct resource *res;
int irq;
bool console = false;
struct uart_driver *drv;
if (of_device_is_compatible(pdev->dev.of_node, "qcom,geni-debug-uart"))
console = true;
if (pdev->dev.of_node) {
if (console) {
drv = &qcom_geni_console_driver;
line = of_alias_get_id(pdev->dev.of_node, "serial");
} else {
drv = &qcom_geni_uart_driver;
line = of_alias_get_id(pdev->dev.of_node, "hsuart");
}
}
port = get_port_from_line(line, console);
if (IS_ERR(port)) {
dev_err(&pdev->dev, "Invalid line %d\n", line);
return PTR_ERR(port);
}
uport = &port->uport;
/* Don't allow 2 drivers to access the same port */
if (uport->private_data)
return -ENODEV;
uport->dev = &pdev->dev;
port->se.dev = &pdev->dev;
port->se.wrapper = dev_get_drvdata(pdev->dev.parent);
port->se.clk = devm_clk_get(&pdev->dev, "se");
if (IS_ERR(port->se.clk)) {
ret = PTR_ERR(port->se.clk);
dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret);
return ret;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
return -EINVAL;
uport->mapbase = res->start;
port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
port->tx_fifo_width = DEF_FIFO_WIDTH_BITS;
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(&pdev->dev, "Failed to get IRQ %d\n", irq);
return irq;
}
uport->irq = irq;
uport->private_data = drv;
platform_set_drvdata(pdev, port);
port->handle_rx = console ? handle_rx_console : handle_rx_uart;
if (!console)
device_create_file(uport->dev, &dev_attr_loopback);
return uart_add_one_port(drv, uport);
}
static int qcom_geni_serial_remove(struct platform_device *pdev)
{
struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
struct uart_driver *drv = port->uport.private_data;
uart_remove_one_port(drv, &port->uport);
return 0;
}
static int __maybe_unused qcom_geni_serial_sys_suspend_noirq(struct device *dev)
{
struct qcom_geni_serial_port *port = dev_get_drvdata(dev);
struct uart_port *uport = &port->uport;
if (uart_console(uport)) {
uart_suspend_port(uport->private_data, uport);
} else {
struct uart_state *state = uport->state;
/*
* If the port is open, deny system suspend.
*/
if (state->pm_state == UART_PM_STATE_ON)
return -EBUSY;
}
return 0;
}
static int __maybe_unused qcom_geni_serial_sys_resume_noirq(struct device *dev)
{
struct qcom_geni_serial_port *port = dev_get_drvdata(dev);
struct uart_port *uport = &port->uport;
if (uart_console(uport) &&
console_suspend_enabled && uport->suspended) {
uart_resume_port(uport->private_data, uport);
/*
* uart_suspend_port() invokes port shutdown which in turn
* frees the irq. uart_resume_port invokes port startup which
* performs request_irq. The request_irq auto-enables the IRQ.
* In addition, resume_noirq implicitly enables the IRQ and
* leads to an unbalanced IRQ enable warning. Disable the IRQ
* before returning so that the warning is suppressed.
*/
disable_irq(uport->irq);
}
return 0;
}
static const struct dev_pm_ops qcom_geni_serial_pm_ops = {
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(qcom_geni_serial_sys_suspend_noirq,
qcom_geni_serial_sys_resume_noirq)
};
static const struct of_device_id qcom_geni_serial_match_table[] = {
{ .compatible = "qcom,geni-debug-uart", },
{ .compatible = "qcom,geni-uart", },
{}
};
MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table);
static struct platform_driver qcom_geni_serial_platform_driver = {
.remove = qcom_geni_serial_remove,
.probe = qcom_geni_serial_probe,
.driver = {
.name = "qcom_geni_serial",
.of_match_table = qcom_geni_serial_match_table,
.pm = &qcom_geni_serial_pm_ops,
},
};
static int __init qcom_geni_serial_init(void)
{
int ret;
ret = console_register(&qcom_geni_console_driver);
if (ret)
return ret;
ret = uart_register_driver(&qcom_geni_uart_driver);
if (ret) {
console_unregister(&qcom_geni_console_driver);
return ret;
}
ret = platform_driver_register(&qcom_geni_serial_platform_driver);
if (ret) {
console_unregister(&qcom_geni_console_driver);
uart_unregister_driver(&qcom_geni_uart_driver);
}
return ret;
}
module_init(qcom_geni_serial_init);
static void __exit qcom_geni_serial_exit(void)
{
platform_driver_unregister(&qcom_geni_serial_platform_driver);
console_unregister(&qcom_geni_console_driver);
uart_unregister_driver(&qcom_geni_uart_driver);
}
module_exit(qcom_geni_serial_exit);
MODULE_DESCRIPTION("Serial driver for GENI based QUP cores");
MODULE_LICENSE("GPL v2");