| /* | |
| * linux/arch/arm/mach-versatile/core.c | |
| * | |
| * Copyright (C) 1999 - 2003 ARM Limited | |
| * Copyright (C) 2000 Deep Blue Solutions Ltd | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License, or | |
| * (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
| */ | |
| #include <linux/config.h> | |
| #include <linux/init.h> | |
| #include <linux/device.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/sysdev.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/amba/bus.h> | |
| #include <linux/amba/clcd.h> | |
| #include <asm/system.h> | |
| #include <asm/hardware.h> | |
| #include <asm/io.h> | |
| #include <asm/irq.h> | |
| #include <asm/leds.h> | |
| #include <asm/hardware/arm_timer.h> | |
| #include <asm/hardware/icst307.h> | |
| #include <asm/hardware/vic.h> | |
| #include <asm/mach/arch.h> | |
| #include <asm/mach/flash.h> | |
| #include <asm/mach/irq.h> | |
| #include <asm/mach/time.h> | |
| #include <asm/mach/map.h> | |
| #include <asm/mach/mmc.h> | |
| #include "core.h" | |
| #include "clock.h" | |
| /* | |
| * All IO addresses are mapped onto VA 0xFFFx.xxxx, where x.xxxx | |
| * is the (PA >> 12). | |
| * | |
| * Setup a VA for the Versatile Vectored Interrupt Controller. | |
| */ | |
| #define __io_address(n) __io(IO_ADDRESS(n)) | |
| #define VA_VIC_BASE __io_address(VERSATILE_VIC_BASE) | |
| #define VA_SIC_BASE __io_address(VERSATILE_SIC_BASE) | |
| static void sic_mask_irq(unsigned int irq) | |
| { | |
| irq -= IRQ_SIC_START; | |
| writel(1 << irq, VA_SIC_BASE + SIC_IRQ_ENABLE_CLEAR); | |
| } | |
| static void sic_unmask_irq(unsigned int irq) | |
| { | |
| irq -= IRQ_SIC_START; | |
| writel(1 << irq, VA_SIC_BASE + SIC_IRQ_ENABLE_SET); | |
| } | |
| static struct irqchip sic_chip = { | |
| .ack = sic_mask_irq, | |
| .mask = sic_mask_irq, | |
| .unmask = sic_unmask_irq, | |
| }; | |
| static void | |
| sic_handle_irq(unsigned int irq, struct irqdesc *desc, struct pt_regs *regs) | |
| { | |
| unsigned long status = readl(VA_SIC_BASE + SIC_IRQ_STATUS); | |
| if (status == 0) { | |
| do_bad_IRQ(irq, desc, regs); | |
| return; | |
| } | |
| do { | |
| irq = ffs(status) - 1; | |
| status &= ~(1 << irq); | |
| irq += IRQ_SIC_START; | |
| desc = irq_desc + irq; | |
| desc_handle_irq(irq, desc, regs); | |
| } while (status); | |
| } | |
| #if 1 | |
| #define IRQ_MMCI0A IRQ_VICSOURCE22 | |
| #define IRQ_AACI IRQ_VICSOURCE24 | |
| #define IRQ_ETH IRQ_VICSOURCE25 | |
| #define PIC_MASK 0xFFD00000 | |
| #else | |
| #define IRQ_MMCI0A IRQ_SIC_MMCI0A | |
| #define IRQ_AACI IRQ_SIC_AACI | |
| #define IRQ_ETH IRQ_SIC_ETH | |
| #define PIC_MASK 0 | |
| #endif | |
| void __init versatile_init_irq(void) | |
| { | |
| unsigned int i; | |
| vic_init(VA_VIC_BASE, IRQ_VIC_START, ~(1 << 31)); | |
| set_irq_handler(IRQ_VICSOURCE31, sic_handle_irq); | |
| enable_irq(IRQ_VICSOURCE31); | |
| /* Do second interrupt controller */ | |
| writel(~0, VA_SIC_BASE + SIC_IRQ_ENABLE_CLEAR); | |
| for (i = IRQ_SIC_START; i <= IRQ_SIC_END; i++) { | |
| if ((PIC_MASK & (1 << (i - IRQ_SIC_START))) == 0) { | |
| set_irq_chip(i, &sic_chip); | |
| set_irq_handler(i, do_level_IRQ); | |
| set_irq_flags(i, IRQF_VALID | IRQF_PROBE); | |
| } | |
| } | |
| /* | |
| * Interrupts on secondary controller from 0 to 8 are routed to | |
| * source 31 on PIC. | |
| * Interrupts from 21 to 31 are routed directly to the VIC on | |
| * the corresponding number on primary controller. This is controlled | |
| * by setting PIC_ENABLEx. | |
| */ | |
| writel(PIC_MASK, VA_SIC_BASE + SIC_INT_PIC_ENABLE); | |
| } | |
| static struct map_desc versatile_io_desc[] __initdata = { | |
| { | |
| .virtual = IO_ADDRESS(VERSATILE_SYS_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_SYS_BASE), | |
| .length = SZ_4K, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = IO_ADDRESS(VERSATILE_SIC_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_SIC_BASE), | |
| .length = SZ_4K, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = IO_ADDRESS(VERSATILE_VIC_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_VIC_BASE), | |
| .length = SZ_4K, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = IO_ADDRESS(VERSATILE_SCTL_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_SCTL_BASE), | |
| .length = SZ_4K * 9, | |
| .type = MT_DEVICE | |
| }, | |
| #ifdef CONFIG_MACH_VERSATILE_AB | |
| { | |
| .virtual = IO_ADDRESS(VERSATILE_GPIO0_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_GPIO0_BASE), | |
| .length = SZ_4K, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = IO_ADDRESS(VERSATILE_IB2_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_IB2_BASE), | |
| .length = SZ_64M, | |
| .type = MT_DEVICE | |
| }, | |
| #endif | |
| #ifdef CONFIG_DEBUG_LL | |
| { | |
| .virtual = IO_ADDRESS(VERSATILE_UART0_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_UART0_BASE), | |
| .length = SZ_4K, | |
| .type = MT_DEVICE | |
| }, | |
| #endif | |
| #ifdef CONFIG_PCI | |
| { | |
| .virtual = IO_ADDRESS(VERSATILE_PCI_CORE_BASE), | |
| .pfn = __phys_to_pfn(VERSATILE_PCI_CORE_BASE), | |
| .length = SZ_4K, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = VERSATILE_PCI_VIRT_BASE, | |
| .pfn = __phys_to_pfn(VERSATILE_PCI_BASE), | |
| .length = VERSATILE_PCI_BASE_SIZE, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = VERSATILE_PCI_CFG_VIRT_BASE, | |
| .pfn = __phys_to_pfn(VERSATILE_PCI_CFG_BASE), | |
| .length = VERSATILE_PCI_CFG_BASE_SIZE, | |
| .type = MT_DEVICE | |
| }, | |
| #if 0 | |
| { | |
| .virtual = VERSATILE_PCI_VIRT_MEM_BASE0, | |
| .pfn = __phys_to_pfn(VERSATILE_PCI_MEM_BASE0), | |
| .length = SZ_16M, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = VERSATILE_PCI_VIRT_MEM_BASE1, | |
| .pfn = __phys_to_pfn(VERSATILE_PCI_MEM_BASE1), | |
| .length = SZ_16M, | |
| .type = MT_DEVICE | |
| }, { | |
| .virtual = VERSATILE_PCI_VIRT_MEM_BASE2, | |
| .pfn = __phys_to_pfn(VERSATILE_PCI_MEM_BASE2), | |
| .length = SZ_16M, | |
| .type = MT_DEVICE | |
| }, | |
| #endif | |
| #endif | |
| }; | |
| void __init versatile_map_io(void) | |
| { | |
| iotable_init(versatile_io_desc, ARRAY_SIZE(versatile_io_desc)); | |
| } | |
| #define VERSATILE_REFCOUNTER (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_24MHz_OFFSET) | |
| /* | |
| * This is the Versatile sched_clock implementation. This has | |
| * a resolution of 41.7ns, and a maximum value of about 179s. | |
| */ | |
| unsigned long long sched_clock(void) | |
| { | |
| unsigned long long v; | |
| v = (unsigned long long)readl(VERSATILE_REFCOUNTER) * 125; | |
| do_div(v, 3); | |
| return v; | |
| } | |
| #define VERSATILE_FLASHCTRL (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_FLASH_OFFSET) | |
| static int versatile_flash_init(void) | |
| { | |
| u32 val; | |
| val = __raw_readl(VERSATILE_FLASHCTRL); | |
| val &= ~VERSATILE_FLASHPROG_FLVPPEN; | |
| __raw_writel(val, VERSATILE_FLASHCTRL); | |
| return 0; | |
| } | |
| static void versatile_flash_exit(void) | |
| { | |
| u32 val; | |
| val = __raw_readl(VERSATILE_FLASHCTRL); | |
| val &= ~VERSATILE_FLASHPROG_FLVPPEN; | |
| __raw_writel(val, VERSATILE_FLASHCTRL); | |
| } | |
| static void versatile_flash_set_vpp(int on) | |
| { | |
| u32 val; | |
| val = __raw_readl(VERSATILE_FLASHCTRL); | |
| if (on) | |
| val |= VERSATILE_FLASHPROG_FLVPPEN; | |
| else | |
| val &= ~VERSATILE_FLASHPROG_FLVPPEN; | |
| __raw_writel(val, VERSATILE_FLASHCTRL); | |
| } | |
| static struct flash_platform_data versatile_flash_data = { | |
| .map_name = "cfi_probe", | |
| .width = 4, | |
| .init = versatile_flash_init, | |
| .exit = versatile_flash_exit, | |
| .set_vpp = versatile_flash_set_vpp, | |
| }; | |
| static struct resource versatile_flash_resource = { | |
| .start = VERSATILE_FLASH_BASE, | |
| .end = VERSATILE_FLASH_BASE + VERSATILE_FLASH_SIZE, | |
| .flags = IORESOURCE_MEM, | |
| }; | |
| static struct platform_device versatile_flash_device = { | |
| .name = "armflash", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &versatile_flash_data, | |
| }, | |
| .num_resources = 1, | |
| .resource = &versatile_flash_resource, | |
| }; | |
| static struct resource smc91x_resources[] = { | |
| [0] = { | |
| .start = VERSATILE_ETH_BASE, | |
| .end = VERSATILE_ETH_BASE + SZ_64K - 1, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| [1] = { | |
| .start = IRQ_ETH, | |
| .end = IRQ_ETH, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static struct platform_device smc91x_device = { | |
| .name = "smc91x", | |
| .id = 0, | |
| .num_resources = ARRAY_SIZE(smc91x_resources), | |
| .resource = smc91x_resources, | |
| }; | |
| #define VERSATILE_SYSMCI (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_MCI_OFFSET) | |
| unsigned int mmc_status(struct device *dev) | |
| { | |
| struct amba_device *adev = container_of(dev, struct amba_device, dev); | |
| u32 mask; | |
| if (adev->res.start == VERSATILE_MMCI0_BASE) | |
| mask = 1; | |
| else | |
| mask = 2; | |
| return readl(VERSATILE_SYSMCI) & mask; | |
| } | |
| static struct mmc_platform_data mmc0_plat_data = { | |
| .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, | |
| .status = mmc_status, | |
| }; | |
| /* | |
| * Clock handling | |
| */ | |
| static const struct icst307_params versatile_oscvco_params = { | |
| .ref = 24000, | |
| .vco_max = 200000, | |
| .vd_min = 4 + 8, | |
| .vd_max = 511 + 8, | |
| .rd_min = 1 + 2, | |
| .rd_max = 127 + 2, | |
| }; | |
| static void versatile_oscvco_set(struct clk *clk, struct icst307_vco vco) | |
| { | |
| void __iomem *sys_lock = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_LOCK_OFFSET; | |
| #if defined(CONFIG_ARCH_VERSATILE_PB) | |
| void __iomem *sys_osc = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_OSC4_OFFSET; | |
| #elif defined(CONFIG_MACH_VERSATILE_AB) | |
| void __iomem *sys_osc = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_OSC1_OFFSET; | |
| #endif | |
| u32 val; | |
| val = readl(sys_osc) & ~0x7ffff; | |
| val |= vco.v | (vco.r << 9) | (vco.s << 16); | |
| writel(0xa05f, sys_lock); | |
| writel(val, sys_osc); | |
| writel(0, sys_lock); | |
| } | |
| static struct clk versatile_clcd_clk = { | |
| .name = "CLCDCLK", | |
| .params = &versatile_oscvco_params, | |
| .setvco = versatile_oscvco_set, | |
| }; | |
| /* | |
| * CLCD support. | |
| */ | |
| #define SYS_CLCD_MODE_MASK (3 << 0) | |
| #define SYS_CLCD_MODE_888 (0 << 0) | |
| #define SYS_CLCD_MODE_5551 (1 << 0) | |
| #define SYS_CLCD_MODE_565_RLSB (2 << 0) | |
| #define SYS_CLCD_MODE_565_BLSB (3 << 0) | |
| #define SYS_CLCD_NLCDIOON (1 << 2) | |
| #define SYS_CLCD_VDDPOSSWITCH (1 << 3) | |
| #define SYS_CLCD_PWR3V5SWITCH (1 << 4) | |
| #define SYS_CLCD_ID_MASK (0x1f << 8) | |
| #define SYS_CLCD_ID_SANYO_3_8 (0x00 << 8) | |
| #define SYS_CLCD_ID_UNKNOWN_8_4 (0x01 << 8) | |
| #define SYS_CLCD_ID_EPSON_2_2 (0x02 << 8) | |
| #define SYS_CLCD_ID_SANYO_2_5 (0x07 << 8) | |
| #define SYS_CLCD_ID_VGA (0x1f << 8) | |
| static struct clcd_panel vga = { | |
| .mode = { | |
| .name = "VGA", | |
| .refresh = 60, | |
| .xres = 640, | |
| .yres = 480, | |
| .pixclock = 39721, | |
| .left_margin = 40, | |
| .right_margin = 24, | |
| .upper_margin = 32, | |
| .lower_margin = 11, | |
| .hsync_len = 96, | |
| .vsync_len = 2, | |
| .sync = 0, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_BCD | TIM2_IPC, | |
| .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1), | |
| .bpp = 16, | |
| }; | |
| static struct clcd_panel sanyo_3_8_in = { | |
| .mode = { | |
| .name = "Sanyo QVGA", | |
| .refresh = 116, | |
| .xres = 320, | |
| .yres = 240, | |
| .pixclock = 100000, | |
| .left_margin = 6, | |
| .right_margin = 6, | |
| .upper_margin = 5, | |
| .lower_margin = 5, | |
| .hsync_len = 6, | |
| .vsync_len = 6, | |
| .sync = 0, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_BCD, | |
| .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1), | |
| .bpp = 16, | |
| }; | |
| static struct clcd_panel sanyo_2_5_in = { | |
| .mode = { | |
| .name = "Sanyo QVGA Portrait", | |
| .refresh = 116, | |
| .xres = 240, | |
| .yres = 320, | |
| .pixclock = 100000, | |
| .left_margin = 20, | |
| .right_margin = 10, | |
| .upper_margin = 2, | |
| .lower_margin = 2, | |
| .hsync_len = 10, | |
| .vsync_len = 2, | |
| .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_IVS | TIM2_IHS | TIM2_IPC, | |
| .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1), | |
| .bpp = 16, | |
| }; | |
| static struct clcd_panel epson_2_2_in = { | |
| .mode = { | |
| .name = "Epson QCIF", | |
| .refresh = 390, | |
| .xres = 176, | |
| .yres = 220, | |
| .pixclock = 62500, | |
| .left_margin = 3, | |
| .right_margin = 2, | |
| .upper_margin = 1, | |
| .lower_margin = 0, | |
| .hsync_len = 3, | |
| .vsync_len = 2, | |
| .sync = 0, | |
| .vmode = FB_VMODE_NONINTERLACED, | |
| }, | |
| .width = -1, | |
| .height = -1, | |
| .tim2 = TIM2_BCD | TIM2_IPC, | |
| .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1), | |
| .bpp = 16, | |
| }; | |
| /* | |
| * Detect which LCD panel is connected, and return the appropriate | |
| * clcd_panel structure. Note: we do not have any information on | |
| * the required timings for the 8.4in panel, so we presently assume | |
| * VGA timings. | |
| */ | |
| static struct clcd_panel *versatile_clcd_panel(void) | |
| { | |
| void __iomem *sys_clcd = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET; | |
| struct clcd_panel *panel = &vga; | |
| u32 val; | |
| val = readl(sys_clcd) & SYS_CLCD_ID_MASK; | |
| if (val == SYS_CLCD_ID_SANYO_3_8) | |
| panel = &sanyo_3_8_in; | |
| else if (val == SYS_CLCD_ID_SANYO_2_5) | |
| panel = &sanyo_2_5_in; | |
| else if (val == SYS_CLCD_ID_EPSON_2_2) | |
| panel = &epson_2_2_in; | |
| else if (val == SYS_CLCD_ID_VGA) | |
| panel = &vga; | |
| else { | |
| printk(KERN_ERR "CLCD: unknown LCD panel ID 0x%08x, using VGA\n", | |
| val); | |
| panel = &vga; | |
| } | |
| return panel; | |
| } | |
| /* | |
| * Disable all display connectors on the interface module. | |
| */ | |
| static void versatile_clcd_disable(struct clcd_fb *fb) | |
| { | |
| void __iomem *sys_clcd = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET; | |
| u32 val; | |
| val = readl(sys_clcd); | |
| val &= ~SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH; | |
| writel(val, sys_clcd); | |
| #ifdef CONFIG_MACH_VERSATILE_AB | |
| /* | |
| * If the LCD is Sanyo 2x5 in on the IB2 board, turn the back-light off | |
| */ | |
| if (fb->panel == &sanyo_2_5_in) { | |
| void __iomem *versatile_ib2_ctrl = __io_address(VERSATILE_IB2_CTRL); | |
| unsigned long ctrl; | |
| ctrl = readl(versatile_ib2_ctrl); | |
| ctrl &= ~0x01; | |
| writel(ctrl, versatile_ib2_ctrl); | |
| } | |
| #endif | |
| } | |
| /* | |
| * Enable the relevant connector on the interface module. | |
| */ | |
| static void versatile_clcd_enable(struct clcd_fb *fb) | |
| { | |
| void __iomem *sys_clcd = __io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET; | |
| u32 val; | |
| val = readl(sys_clcd); | |
| val &= ~SYS_CLCD_MODE_MASK; | |
| switch (fb->fb.var.green.length) { | |
| case 5: | |
| val |= SYS_CLCD_MODE_5551; | |
| break; | |
| case 6: | |
| val |= SYS_CLCD_MODE_565_RLSB; | |
| break; | |
| case 8: | |
| val |= SYS_CLCD_MODE_888; | |
| break; | |
| } | |
| /* | |
| * Set the MUX | |
| */ | |
| writel(val, sys_clcd); | |
| /* | |
| * And now enable the PSUs | |
| */ | |
| val |= SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH; | |
| writel(val, sys_clcd); | |
| #ifdef CONFIG_MACH_VERSATILE_AB | |
| /* | |
| * If the LCD is Sanyo 2x5 in on the IB2 board, turn the back-light on | |
| */ | |
| if (fb->panel == &sanyo_2_5_in) { | |
| void __iomem *versatile_ib2_ctrl = __io_address(VERSATILE_IB2_CTRL); | |
| unsigned long ctrl; | |
| ctrl = readl(versatile_ib2_ctrl); | |
| ctrl |= 0x01; | |
| writel(ctrl, versatile_ib2_ctrl); | |
| } | |
| #endif | |
| } | |
| static unsigned long framesize = SZ_1M; | |
| static int versatile_clcd_setup(struct clcd_fb *fb) | |
| { | |
| dma_addr_t dma; | |
| fb->panel = versatile_clcd_panel(); | |
| fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize, | |
| &dma, GFP_KERNEL); | |
| if (!fb->fb.screen_base) { | |
| printk(KERN_ERR "CLCD: unable to map framebuffer\n"); | |
| return -ENOMEM; | |
| } | |
| fb->fb.fix.smem_start = dma; | |
| fb->fb.fix.smem_len = framesize; | |
| return 0; | |
| } | |
| static int versatile_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma) | |
| { | |
| return dma_mmap_writecombine(&fb->dev->dev, vma, | |
| fb->fb.screen_base, | |
| fb->fb.fix.smem_start, | |
| fb->fb.fix.smem_len); | |
| } | |
| static void versatile_clcd_remove(struct clcd_fb *fb) | |
| { | |
| dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len, | |
| fb->fb.screen_base, fb->fb.fix.smem_start); | |
| } | |
| static struct clcd_board clcd_plat_data = { | |
| .name = "Versatile", | |
| .check = clcdfb_check, | |
| .decode = clcdfb_decode, | |
| .disable = versatile_clcd_disable, | |
| .enable = versatile_clcd_enable, | |
| .setup = versatile_clcd_setup, | |
| .mmap = versatile_clcd_mmap, | |
| .remove = versatile_clcd_remove, | |
| }; | |
| #define AACI_IRQ { IRQ_AACI, NO_IRQ } | |
| #define AACI_DMA { 0x80, 0x81 } | |
| #define MMCI0_IRQ { IRQ_MMCI0A,IRQ_SIC_MMCI0B } | |
| #define MMCI0_DMA { 0x84, 0 } | |
| #define KMI0_IRQ { IRQ_SIC_KMI0, NO_IRQ } | |
| #define KMI0_DMA { 0, 0 } | |
| #define KMI1_IRQ { IRQ_SIC_KMI1, NO_IRQ } | |
| #define KMI1_DMA { 0, 0 } | |
| /* | |
| * These devices are connected directly to the multi-layer AHB switch | |
| */ | |
| #define SMC_IRQ { NO_IRQ, NO_IRQ } | |
| #define SMC_DMA { 0, 0 } | |
| #define MPMC_IRQ { NO_IRQ, NO_IRQ } | |
| #define MPMC_DMA { 0, 0 } | |
| #define CLCD_IRQ { IRQ_CLCDINT, NO_IRQ } | |
| #define CLCD_DMA { 0, 0 } | |
| #define DMAC_IRQ { IRQ_DMAINT, NO_IRQ } | |
| #define DMAC_DMA { 0, 0 } | |
| /* | |
| * These devices are connected via the core APB bridge | |
| */ | |
| #define SCTL_IRQ { NO_IRQ, NO_IRQ } | |
| #define SCTL_DMA { 0, 0 } | |
| #define WATCHDOG_IRQ { IRQ_WDOGINT, NO_IRQ } | |
| #define WATCHDOG_DMA { 0, 0 } | |
| #define GPIO0_IRQ { IRQ_GPIOINT0, NO_IRQ } | |
| #define GPIO0_DMA { 0, 0 } | |
| #define GPIO1_IRQ { IRQ_GPIOINT1, NO_IRQ } | |
| #define GPIO1_DMA { 0, 0 } | |
| #define RTC_IRQ { IRQ_RTCINT, NO_IRQ } | |
| #define RTC_DMA { 0, 0 } | |
| /* | |
| * These devices are connected via the DMA APB bridge | |
| */ | |
| #define SCI_IRQ { IRQ_SCIINT, NO_IRQ } | |
| #define SCI_DMA { 7, 6 } | |
| #define UART0_IRQ { IRQ_UARTINT0, NO_IRQ } | |
| #define UART0_DMA { 15, 14 } | |
| #define UART1_IRQ { IRQ_UARTINT1, NO_IRQ } | |
| #define UART1_DMA { 13, 12 } | |
| #define UART2_IRQ { IRQ_UARTINT2, NO_IRQ } | |
| #define UART2_DMA { 11, 10 } | |
| #define SSP_IRQ { IRQ_SSPINT, NO_IRQ } | |
| #define SSP_DMA { 9, 8 } | |
| /* FPGA Primecells */ | |
| AMBA_DEVICE(aaci, "fpga:04", AACI, NULL); | |
| AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &mmc0_plat_data); | |
| AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL); | |
| AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL); | |
| /* DevChip Primecells */ | |
| AMBA_DEVICE(smc, "dev:00", SMC, NULL); | |
| AMBA_DEVICE(mpmc, "dev:10", MPMC, NULL); | |
| AMBA_DEVICE(clcd, "dev:20", CLCD, &clcd_plat_data); | |
| AMBA_DEVICE(dmac, "dev:30", DMAC, NULL); | |
| AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL); | |
| AMBA_DEVICE(wdog, "dev:e1", WATCHDOG, NULL); | |
| AMBA_DEVICE(gpio0, "dev:e4", GPIO0, NULL); | |
| AMBA_DEVICE(gpio1, "dev:e5", GPIO1, NULL); | |
| AMBA_DEVICE(rtc, "dev:e8", RTC, NULL); | |
| AMBA_DEVICE(sci0, "dev:f0", SCI, NULL); | |
| AMBA_DEVICE(uart0, "dev:f1", UART0, NULL); | |
| AMBA_DEVICE(uart1, "dev:f2", UART1, NULL); | |
| AMBA_DEVICE(uart2, "dev:f3", UART2, NULL); | |
| AMBA_DEVICE(ssp0, "dev:f4", SSP, NULL); | |
| static struct amba_device *amba_devs[] __initdata = { | |
| &dmac_device, | |
| &uart0_device, | |
| &uart1_device, | |
| &uart2_device, | |
| &smc_device, | |
| &mpmc_device, | |
| &clcd_device, | |
| &sctl_device, | |
| &wdog_device, | |
| &gpio0_device, | |
| &gpio1_device, | |
| &rtc_device, | |
| &sci0_device, | |
| &ssp0_device, | |
| &aaci_device, | |
| &mmc0_device, | |
| &kmi0_device, | |
| &kmi1_device, | |
| }; | |
| #ifdef CONFIG_LEDS | |
| #define VA_LEDS_BASE (__io_address(VERSATILE_SYS_BASE) + VERSATILE_SYS_LED_OFFSET) | |
| static void versatile_leds_event(led_event_t ledevt) | |
| { | |
| unsigned long flags; | |
| u32 val; | |
| local_irq_save(flags); | |
| val = readl(VA_LEDS_BASE); | |
| switch (ledevt) { | |
| case led_idle_start: | |
| val = val & ~VERSATILE_SYS_LED0; | |
| break; | |
| case led_idle_end: | |
| val = val | VERSATILE_SYS_LED0; | |
| break; | |
| case led_timer: | |
| val = val ^ VERSATILE_SYS_LED1; | |
| break; | |
| case led_halted: | |
| val = 0; | |
| break; | |
| default: | |
| break; | |
| } | |
| writel(val, VA_LEDS_BASE); | |
| local_irq_restore(flags); | |
| } | |
| #endif /* CONFIG_LEDS */ | |
| void __init versatile_init(void) | |
| { | |
| int i; | |
| clk_register(&versatile_clcd_clk); | |
| platform_device_register(&versatile_flash_device); | |
| platform_device_register(&smc91x_device); | |
| for (i = 0; i < ARRAY_SIZE(amba_devs); i++) { | |
| struct amba_device *d = amba_devs[i]; | |
| amba_device_register(d, &iomem_resource); | |
| } | |
| #ifdef CONFIG_LEDS | |
| leds_event = versatile_leds_event; | |
| #endif | |
| } | |
| /* | |
| * Where is the timer (VA)? | |
| */ | |
| #define TIMER0_VA_BASE __io_address(VERSATILE_TIMER0_1_BASE) | |
| #define TIMER1_VA_BASE (__io_address(VERSATILE_TIMER0_1_BASE) + 0x20) | |
| #define TIMER2_VA_BASE __io_address(VERSATILE_TIMER2_3_BASE) | |
| #define TIMER3_VA_BASE (__io_address(VERSATILE_TIMER2_3_BASE) + 0x20) | |
| #define VA_IC_BASE __io_address(VERSATILE_VIC_BASE) | |
| /* | |
| * How long is the timer interval? | |
| */ | |
| #define TIMER_INTERVAL (TICKS_PER_uSEC * mSEC_10) | |
| #if TIMER_INTERVAL >= 0x100000 | |
| #define TIMER_RELOAD (TIMER_INTERVAL >> 8) | |
| #define TIMER_DIVISOR (TIMER_CTRL_DIV256) | |
| #define TICKS2USECS(x) (256 * (x) / TICKS_PER_uSEC) | |
| #elif TIMER_INTERVAL >= 0x10000 | |
| #define TIMER_RELOAD (TIMER_INTERVAL >> 4) /* Divide by 16 */ | |
| #define TIMER_DIVISOR (TIMER_CTRL_DIV16) | |
| #define TICKS2USECS(x) (16 * (x) / TICKS_PER_uSEC) | |
| #else | |
| #define TIMER_RELOAD (TIMER_INTERVAL) | |
| #define TIMER_DIVISOR (TIMER_CTRL_DIV1) | |
| #define TICKS2USECS(x) ((x) / TICKS_PER_uSEC) | |
| #endif | |
| /* | |
| * Returns number of ms since last clock interrupt. Note that interrupts | |
| * will have been disabled by do_gettimeoffset() | |
| */ | |
| static unsigned long versatile_gettimeoffset(void) | |
| { | |
| unsigned long ticks1, ticks2, status; | |
| /* | |
| * Get the current number of ticks. Note that there is a race | |
| * condition between us reading the timer and checking for | |
| * an interrupt. We get around this by ensuring that the | |
| * counter has not reloaded between our two reads. | |
| */ | |
| ticks2 = readl(TIMER0_VA_BASE + TIMER_VALUE) & 0xffff; | |
| do { | |
| ticks1 = ticks2; | |
| status = __raw_readl(VA_IC_BASE + VIC_RAW_STATUS); | |
| ticks2 = readl(TIMER0_VA_BASE + TIMER_VALUE) & 0xffff; | |
| } while (ticks2 > ticks1); | |
| /* | |
| * Number of ticks since last interrupt. | |
| */ | |
| ticks1 = TIMER_RELOAD - ticks2; | |
| /* | |
| * Interrupt pending? If so, we've reloaded once already. | |
| * | |
| * FIXME: Need to check this is effectively timer 0 that expires | |
| */ | |
| if (status & IRQMASK_TIMERINT0_1) | |
| ticks1 += TIMER_RELOAD; | |
| /* | |
| * Convert the ticks to usecs | |
| */ | |
| return TICKS2USECS(ticks1); | |
| } | |
| /* | |
| * IRQ handler for the timer | |
| */ | |
| static irqreturn_t versatile_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs) | |
| { | |
| write_seqlock(&xtime_lock); | |
| // ...clear the interrupt | |
| writel(1, TIMER0_VA_BASE + TIMER_INTCLR); | |
| timer_tick(regs); | |
| write_sequnlock(&xtime_lock); | |
| return IRQ_HANDLED; | |
| } | |
| static struct irqaction versatile_timer_irq = { | |
| .name = "Versatile Timer Tick", | |
| .flags = SA_INTERRUPT | SA_TIMER, | |
| .handler = versatile_timer_interrupt, | |
| }; | |
| /* | |
| * Set up timer interrupt, and return the current time in seconds. | |
| */ | |
| static void __init versatile_timer_init(void) | |
| { | |
| u32 val; | |
| /* | |
| * set clock frequency: | |
| * VERSATILE_REFCLK is 32KHz | |
| * VERSATILE_TIMCLK is 1MHz | |
| */ | |
| val = readl(__io_address(VERSATILE_SCTL_BASE)); | |
| writel((VERSATILE_TIMCLK << VERSATILE_TIMER1_EnSel) | | |
| (VERSATILE_TIMCLK << VERSATILE_TIMER2_EnSel) | | |
| (VERSATILE_TIMCLK << VERSATILE_TIMER3_EnSel) | | |
| (VERSATILE_TIMCLK << VERSATILE_TIMER4_EnSel) | val, | |
| __io_address(VERSATILE_SCTL_BASE)); | |
| /* | |
| * Initialise to a known state (all timers off) | |
| */ | |
| writel(0, TIMER0_VA_BASE + TIMER_CTRL); | |
| writel(0, TIMER1_VA_BASE + TIMER_CTRL); | |
| writel(0, TIMER2_VA_BASE + TIMER_CTRL); | |
| writel(0, TIMER3_VA_BASE + TIMER_CTRL); | |
| writel(TIMER_RELOAD, TIMER0_VA_BASE + TIMER_LOAD); | |
| writel(TIMER_RELOAD, TIMER0_VA_BASE + TIMER_VALUE); | |
| writel(TIMER_DIVISOR | TIMER_CTRL_ENABLE | TIMER_CTRL_PERIODIC | | |
| TIMER_CTRL_IE, TIMER0_VA_BASE + TIMER_CTRL); | |
| /* | |
| * Make irqs happen for the system timer | |
| */ | |
| setup_irq(IRQ_TIMERINT0_1, &versatile_timer_irq); | |
| } | |
| struct sys_timer versatile_timer = { | |
| .init = versatile_timer_init, | |
| .offset = versatile_gettimeoffset, | |
| }; |