==================================
Kernel Lock Torture Test Operation
==================================

CONFIG_LOCK_TORTURE_TEST
========================

The CONFIG_LOCK_TORTURE_TEST config option provides a kernel module
that runs torture tests on core kernel locking primitives. The kernel
module, 'locktorture', may be built after the fact on the running
kernel to be tested, if desired. The tests periodically output status
messages via printk(), which can be examined via the dmesg (perhaps
grepping for "torture").  The test is started when the module is loaded,
and stops when the module is unloaded. This program is based on how RCU
is tortured, via rcutorture.

This torture test consists of creating a number of kernel threads which
acquire the lock and hold it for specific amount of time, thus simulating
different critical region behaviors. The amount of contention on the lock
can be simulated by either enlarging this critical region hold time and/or
creating more kthreads.


Module Parameters
=================

This module has the following parameters:


Locktorture-specific
--------------------

nwriters_stress
		  Number of kernel threads that will stress exclusive lock
		  ownership (writers). The default value is twice the number
		  of online CPUs.

nreaders_stress
		  Number of kernel threads that will stress shared lock
		  ownership (readers). The default is the same amount of writer
		  locks. If the user did not specify nwriters_stress, then
		  both readers and writers be the amount of online CPUs.

torture_type
		  Type of lock to torture. By default, only spinlocks will
		  be tortured. This module can torture the following locks,
		  with string values as follows:

		     - "lock_busted":
				Simulates a buggy lock implementation.

		     - "spin_lock":
				spin_lock() and spin_unlock() pairs.

		     - "spin_lock_irq":
				spin_lock_irq() and spin_unlock_irq() pairs.

		     - "rw_lock":
				read/write lock() and unlock() rwlock pairs.

		     - "rw_lock_irq":
				read/write lock_irq() and unlock_irq()
				rwlock pairs.

		     - "mutex_lock":
				mutex_lock() and mutex_unlock() pairs.

		     - "rtmutex_lock":
				rtmutex_lock() and rtmutex_unlock() pairs.
				Kernel must have CONFIG_RT_MUTEXES=y.

		     - "rwsem_lock":
				read/write down() and up() semaphore pairs.


Torture-framework (RCU + locking)
---------------------------------

shutdown_secs
		  The number of seconds to run the test before terminating
		  the test and powering off the system.  The default is
		  zero, which disables test termination and system shutdown.
		  This capability is useful for automated testing.

onoff_interval
		  The number of seconds between each attempt to execute a
		  randomly selected CPU-hotplug operation.  Defaults
		  to zero, which disables CPU hotplugging.  In
		  CONFIG_HOTPLUG_CPU=n kernels, locktorture will silently
		  refuse to do any CPU-hotplug operations regardless of
		  what value is specified for onoff_interval.

onoff_holdoff
		  The number of seconds to wait until starting CPU-hotplug
		  operations.  This would normally only be used when
		  locktorture was built into the kernel and started
		  automatically at boot time, in which case it is useful
		  in order to avoid confusing boot-time code with CPUs
		  coming and going. This parameter is only useful if
		  CONFIG_HOTPLUG_CPU is enabled.

stat_interval
		  Number of seconds between statistics-related printk()s.
		  By default, locktorture will report stats every 60 seconds.
		  Setting the interval to zero causes the statistics to
		  be printed -only- when the module is unloaded.

stutter
		  The length of time to run the test before pausing for this
		  same period of time.  Defaults to "stutter=5", so as
		  to run and pause for (roughly) five-second intervals.
		  Specifying "stutter=0" causes the test to run continuously
		  without pausing.

shuffle_interval
		  The number of seconds to keep the test threads affinitied
		  to a particular subset of the CPUs, defaults to 3 seconds.
		  Used in conjunction with test_no_idle_hz.

verbose
		  Enable verbose debugging printing, via printk(). Enabled
		  by default. This extra information is mostly related to
		  high-level errors and reports from the main 'torture'
		  framework.


Statistics
==========

Statistics are printed in the following format::

  spin_lock-torture: Writes:  Total: 93746064  Max/Min: 0/0   Fail: 0
     (A)		    (B)		   (C)		  (D)	       (E)

  (A): Lock type that is being tortured -- torture_type parameter.

  (B): Number of writer lock acquisitions. If dealing with a read/write
       primitive a second "Reads" statistics line is printed.

  (C): Number of times the lock was acquired.

  (D): Min and max number of times threads failed to acquire the lock.

  (E): true/false values if there were errors acquiring the lock. This should
       -only- be positive if there is a bug in the locking primitive's
       implementation. Otherwise a lock should never fail (i.e., spin_lock()).
       Of course, the same applies for (C), above. A dummy example of this is
       the "lock_busted" type.

Usage
=====

The following script may be used to torture locks::

	#!/bin/sh

	modprobe locktorture
	sleep 3600
	rmmod locktorture
	dmesg | grep torture:

The output can be manually inspected for the error flag of "!!!".
One could of course create a more elaborate script that automatically
checked for such errors.  The "rmmod" command forces a "SUCCESS",
"FAILURE", or "RCU_HOTPLUG" indication to be printk()ed.  The first
two are self-explanatory, while the last indicates that while there
were no locking failures, CPU-hotplug problems were detected.

Also see: Documentation/RCU/torture.rst