| /* |
| * Copyright (C) 2017 Jagan Teki <jteki@openedev.com> |
| * |
| * This file is dual-licensed: you can use it either under the terms |
| * of the GPL or the X11 license, at your option. Note that this dual |
| * licensing only applies to this file, and not this project as a |
| * whole. |
| * |
| * a) This file is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of the |
| * License, or (at your option) any later version. |
| * |
| * This file is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * Or, alternatively, |
| * |
| * b) Permission is hereby granted, free of charge, to any person |
| * obtaining a copy of this software and associated documentation |
| * files (the "Software"), to deal in the Software without |
| * restriction, including without limitation the rights to use, |
| * copy, modify, merge, publish, distribute, sublicense, and/or |
| * sell copies of the Software, and to permit persons to whom the |
| * Software is furnished to do so, subject to the following |
| * conditions: |
| * |
| * The above copyright notice and this permission notice shall be |
| * included in all copies or substantial portions of the Software. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES |
| * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT |
| * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, |
| * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR |
| * OTHER DEALINGS IN THE SOFTWARE. |
| */ |
| |
| #include "sun8i-h3-nanopi.dtsi" |
| |
| / { |
| model = "FriendlyArm NanoPi M1 Plus"; |
| compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3"; |
| |
| aliases { |
| serial1 = &uart3; |
| ethernet0 = &emac; |
| ethernet1 = &sdio_wifi; |
| }; |
| |
| reg_gmac_3v3: gmac-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "gmac-3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| startup-delay-us = <100000>; |
| enable-active-high; |
| gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| wifi_pwrseq: wifi_pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| pinctrl-names = "default"; |
| reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ |
| }; |
| |
| connector { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_con_in: endpoint { |
| remote-endpoint = <&hdmi_out_con>; |
| }; |
| }; |
| }; |
| }; |
| |
| &de { |
| status = "okay"; |
| }; |
| |
| &ehci1 { |
| status = "okay"; |
| }; |
| |
| &ehci2 { |
| status = "okay"; |
| }; |
| |
| &emac { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&emac_rgmii_pins>; |
| phy-supply = <®_gmac_3v3>; |
| phy-handle = <&ext_rgmii_phy>; |
| phy-mode = "rgmii"; |
| |
| status = "okay"; |
| }; |
| |
| &external_mdio { |
| ext_rgmii_phy: ethernet-phy@1 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <7>; |
| }; |
| }; |
| |
| &hdmi { |
| status = "okay"; |
| }; |
| |
| &hdmi_out { |
| hdmi_out_con: endpoint { |
| remote-endpoint = <&hdmi_con_in>; |
| }; |
| }; |
| |
| &ir { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ir_pins_a>; |
| status = "okay"; |
| }; |
| |
| &mmc1 { |
| vmmc-supply = <®_vcc3v3>; |
| vqmmc-supply = <®_vcc3v3>; |
| mmc-pwrseq = <&wifi_pwrseq>; |
| bus-width = <4>; |
| non-removable; |
| status = "okay"; |
| |
| sdio_wifi: sdio_wifi@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| interrupt-parent = <&pio>; |
| interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_8bit_pins>; |
| vmmc-supply = <®_vcc3v3>; |
| vqmmc-supply = <®_vcc3v3>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &ohci1 { |
| status = "okay"; |
| }; |
| |
| &ohci2 { |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>; |
| status = "okay"; |
| }; |