| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| /* |
| * Copyright (C) STMicroelectronics 2017 - All Rights Reserved |
| * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. |
| */ |
| /dts-v1/; |
| |
| #include "stm32mp157c-ed1.dts" |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| model = "STMicroelectronics STM32MP157C eval daughter on eval mother"; |
| compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157"; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| aliases { |
| serial0 = &uart4; |
| ethernet0 = ðernet0; |
| }; |
| |
| panel_backlight: panel-backlight { |
| compatible = "gpio-backlight"; |
| gpios = <&gpiod 13 GPIO_ACTIVE_LOW>; |
| default-on; |
| status = "okay"; |
| }; |
| }; |
| |
| &cec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cec_pins_a>; |
| status = "okay"; |
| }; |
| |
| &dsi { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| dsi_in: endpoint { |
| remote-endpoint = <<dc_ep0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| dsi_out: endpoint { |
| remote-endpoint = <&dsi_panel_in>; |
| }; |
| }; |
| }; |
| |
| panel-dsi@0 { |
| compatible = "raydium,rm68200"; |
| reg = <0>; |
| reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>; |
| backlight = <&panel_backlight>; |
| status = "okay"; |
| |
| port { |
| dsi_panel_in: endpoint { |
| remote-endpoint = <&dsi_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| ðernet0 { |
| status = "okay"; |
| pinctrl-0 = <ðernet0_rgmii_pins_a>; |
| pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; |
| pinctrl-names = "default", "sleep"; |
| phy-mode = "rgmii"; |
| max-speed = <1000>; |
| phy-handle = <&phy0>; |
| |
| mdio0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dwmac-mdio"; |
| phy0: ethernet-phy@0 { |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_pins_a>; |
| i2c-scl-rising-time-ns = <185>; |
| i2c-scl-falling-time-ns = <20>; |
| status = "okay"; |
| }; |
| |
| &i2c5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c5_pins_a>; |
| i2c-scl-rising-time-ns = <185>; |
| i2c-scl-falling-time-ns = <20>; |
| status = "okay"; |
| }; |
| |
| <dc { |
| status = "okay"; |
| |
| port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ltdc_ep0_out: endpoint@0 { |
| reg = <0>; |
| remote-endpoint = <&dsi_in>; |
| }; |
| }; |
| }; |
| |
| &m_can1 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&m_can1_pins_a>; |
| pinctrl-1 = <&m_can1_sleep_pins_a>; |
| status = "okay"; |
| }; |
| |
| &qspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; |
| reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| flash0: mx66l51235l@0 { |
| reg = <0>; |
| spi-rx-bus-width = <4>; |
| spi-max-frequency = <108000000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| }; |
| |
| flash1: mx66l51235l@1 { |
| reg = <1>; |
| spi-rx-bus-width = <4>; |
| spi-max-frequency = <108000000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| }; |
| }; |
| |
| &spi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi1_pins_a>; |
| status = "disabled"; |
| }; |
| |
| &timers2 { |
| /* spare dmas for other usage (un-delete to enable pwm capture) */ |
| /delete-property/dmas; |
| /delete-property/dma-names; |
| status = "disabled"; |
| pwm { |
| pinctrl-0 = <&pwm2_pins_a>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| timer@1 { |
| status = "okay"; |
| }; |
| }; |
| |
| &timers8 { |
| /delete-property/dmas; |
| /delete-property/dma-names; |
| status = "disabled"; |
| pwm { |
| pinctrl-0 = <&pwm8_pins_a>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| timer@7 { |
| status = "okay"; |
| }; |
| }; |
| |
| &timers12 { |
| /delete-property/dmas; |
| /delete-property/dma-names; |
| status = "disabled"; |
| pwm { |
| pinctrl-0 = <&pwm12_pins_a>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| timer@11 { |
| status = "okay"; |
| }; |
| }; |
| |
| &usbh_ehci { |
| phys = <&usbphyc_port0>; |
| phy-names = "usb"; |
| status = "okay"; |
| }; |
| |
| &usbotg_hs { |
| dr_mode = "peripheral"; |
| phys = <&usbphyc_port1 0>; |
| phy-names = "usb2-phy"; |
| status = "okay"; |
| }; |
| |
| &usbphyc { |
| status = "okay"; |
| }; |