| /* |
| * Copyright 2012 ST-Ericsson AB |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include "ste-dbx5x0.dtsi" |
| #include "ste-href-family-pinctrl.dtsi" |
| |
| / { |
| memory { |
| device_type = "memory"; |
| reg = <0x00000000 0x20000000>; |
| }; |
| |
| soc { |
| uart@80120000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&uart0_default_mode>; |
| pinctrl-1 = <&uart0_sleep_mode>; |
| status = "okay"; |
| }; |
| |
| /* This UART is unused and thus left disabled */ |
| uart@80121000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&uart1_default_mode>; |
| pinctrl-1 = <&uart1_sleep_mode>; |
| }; |
| |
| uart@80007000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&uart2_default_mode>; |
| pinctrl-1 = <&uart2_sleep_mode>; |
| status = "okay"; |
| }; |
| |
| i2c@80004000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c0_default_mode>; |
| pinctrl-1 = <&i2c0_sleep_mode>; |
| }; |
| |
| i2c@80122000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c1_default_mode>; |
| pinctrl-1 = <&i2c1_sleep_mode>; |
| }; |
| |
| i2c@80128000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c2_default_mode>; |
| pinctrl-1 = <&i2c2_sleep_mode>; |
| lp5521@33 { |
| compatible = "national,lp5521"; |
| reg = <0x33>; |
| label = "lp5521_pri"; |
| clock-mode = /bits/ 8 <2>; |
| chan0 { |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| chan1 { |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| }; |
| chan2 { |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| }; |
| }; |
| lp5521@34 { |
| compatible = "national,lp5521"; |
| reg = <0x34>; |
| label = "lp5521_sec"; |
| clock-mode = /bits/ 8 <2>; |
| chan0 { |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| }; |
| chan1 { |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| }; |
| chan2 { |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| }; |
| }; |
| bh1780@29 { |
| compatible = "rohm,bh1780gli"; |
| reg = <0x29>; |
| }; |
| }; |
| |
| i2c@80110000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c3_default_mode>; |
| pinctrl-1 = <&i2c3_sleep_mode>; |
| }; |
| |
| /* ST6G3244ME level translator for 1.8/2.9 V */ |
| vmmci: regulator-gpio { |
| compatible = "regulator-gpio"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2900000>; |
| regulator-name = "mmci-reg"; |
| regulator-type = "voltage"; |
| |
| startup-delay-us = <100>; |
| |
| states = <1800000 0x1 |
| 2900000 0x0>; |
| }; |
| |
| // External Micro SD slot |
| sdi0_per1@80126000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| sd-uhs-sdr12; |
| sd-uhs-sdr25; |
| full-pwr-cycle; |
| st,sig-dir-dat0; |
| st,sig-dir-dat2; |
| st,sig-dir-cmd; |
| st,sig-pin-fbclk; |
| vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| vqmmc-supply = <&vmmci>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdi0_default_mode>; |
| pinctrl-1 = <&sdi0_sleep_mode>; |
| |
| status = "okay"; |
| }; |
| |
| // WLAN SDIO channel |
| sdi1_per2@80118000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <4>; |
| non-removable; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdi1_default_mode>; |
| pinctrl-1 = <&sdi1_sleep_mode>; |
| |
| status = "okay"; |
| }; |
| |
| // PoP:ed eMMC |
| sdi2_per3@80005000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| non-removable; |
| vmmc-supply = <&db8500_vsmps2_reg>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdi2_default_mode>; |
| pinctrl-1 = <&sdi2_sleep_mode>; |
| |
| status = "okay"; |
| }; |
| |
| // On-board eMMC |
| sdi4_per2@80114000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| non-removable; |
| vmmc-supply = <&ab8500_ldo_aux2_reg>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdi4_default_mode>; |
| pinctrl-1 = <&sdi4_sleep_mode>; |
| |
| status = "okay"; |
| }; |
| |
| msp0: msp@80123000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&msp0_default_mode>; |
| status = "okay"; |
| }; |
| |
| msp1: msp@80124000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&msp1_default_mode>; |
| status = "okay"; |
| }; |
| |
| msp2: msp@80117000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&msp2_default_mode>; |
| }; |
| |
| msp3: msp@80125000 { |
| status = "okay"; |
| }; |
| |
| prcmu@80157000 { |
| ab8500 { |
| ab8500-gpio { |
| }; |
| |
| ab8500_usb { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&musb_default_mode>; |
| pinctrl-1 = <&musb_sleep_mode>; |
| }; |
| |
| ab8500-regulators { |
| ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { |
| regulator-name = "V-DISPLAY"; |
| }; |
| |
| ab8500_ldo_aux2_reg: ab8500_ldo_aux2 { |
| regulator-name = "V-eMMC1"; |
| }; |
| |
| ab8500_ldo_aux3_reg: ab8500_ldo_aux3 { |
| regulator-name = "V-MMC-SD"; |
| }; |
| |
| ab8500_ldo_intcore_reg: ab8500_ldo_intcore { |
| regulator-name = "V-INTCORE"; |
| }; |
| |
| ab8500_ldo_tvout_reg: ab8500_ldo_tvout { |
| regulator-name = "V-TVOUT"; |
| }; |
| |
| ab8500_ldo_usb_reg: ab8500_ldo_usb { |
| regulator-name = "dummy"; |
| }; |
| |
| ab8500_ldo_audio_reg: ab8500_ldo_audio { |
| regulator-name = "V-AUD"; |
| }; |
| |
| ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 { |
| regulator-name = "V-AMIC1"; |
| }; |
| |
| ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 { |
| regulator-name = "V-AMIC2"; |
| }; |
| |
| ab8500_ldo_dmic_reg: ab8500_ldo_dmic { |
| regulator-name = "V-DMIC"; |
| }; |
| |
| ab8500_ldo_ana_reg: ab8500_ldo_ana { |
| regulator-name = "V-CSI/DSI"; |
| }; |
| }; |
| }; |
| }; |
| |
| mcde@a0350000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&lcd_default_mode>; |
| pinctrl-1 = <&lcd_sleep_mode>; |
| }; |
| }; |
| }; |