| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2016 Andy Yan <andy.yan@rock-chips.com> |
| */ |
| |
| /dts-v1/; |
| #include <dt-bindings/input/input.h> |
| #include "rk3188.dtsi" |
| |
| / { |
| model = "Rockchip PX3-EVB"; |
| compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188"; |
| |
| chosen { |
| stdout-path = "serial2:115200n8"; |
| }; |
| |
| memory@60000000 { |
| reg = <0x60000000 0x80000000>; |
| device_type = "memory"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| |
| power { |
| gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_POWER>; |
| label = "GPIO Key Power"; |
| linux,input-type = <1>; |
| wakeup-source; |
| debounce-interval = <100>; |
| }; |
| }; |
| |
| vcc_sys: vsys-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vsys"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-boot-on; |
| }; |
| }; |
| |
| &cpu0 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu1 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu2 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu3 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &emmc { |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| non-removable; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_rst>; |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| |
| accelerometer@18 { |
| compatible = "bosch,bma250"; |
| reg = <0x18>; |
| interrupt-parent = <&gpio0>; |
| interrupts = <RK_PB7 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| rk808: pmic@1c { |
| compatible = "rockchip,rk818"; |
| reg = <0x1c>; |
| interrupt-parent = <&gpio0>; |
| interrupts = <RK_PB3 IRQ_TYPE_LEVEL_LOW>; |
| rockchip,system-power-controller; |
| wakeup-source; |
| #clock-cells = <1>; |
| clock-output-names = "xin32k", "rk808-clkout2"; |
| |
| vcc1-supply = <&vcc_sys>; |
| vcc2-supply = <&vcc_sys>; |
| vcc3-supply = <&vcc_sys>; |
| vcc4-supply = <&vcc_sys>; |
| vcc6-supply = <&vcc_sys>; |
| vcc7-supply = <&vcc_sys>; |
| vcc8-supply = <&vcc_io>; |
| vcc9-supply = <&vcc_io>; |
| |
| regulators { |
| vdd_cpu: DCDC_REG1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-name = "vdd_arm"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_gpu: DCDC_REG2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1250000>; |
| regulator-name = "vdd_gpu"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1000000>; |
| }; |
| }; |
| |
| vcc_ddr: DCDC_REG3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-name = "vcc_ddr"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| vcc_io: DCDC_REG4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc_io"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3300000>; |
| }; |
| }; |
| |
| vcc_cif: LDO_REG1 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc_cif"; |
| }; |
| |
| vcc_jetta33: LDO_REG2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc_jetta33"; |
| }; |
| |
| vdd_10: LDO_REG3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-name = "vdd_10"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1000000>; |
| }; |
| }; |
| |
| lvds_12: LDO_REG4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "lvds_12"; |
| }; |
| |
| lvds_25: LDO_REG5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "lvds_25"; |
| }; |
| |
| cif_18: LDO_REG6 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-name = "cif_18"; |
| }; |
| |
| vcc_sd: LDO_REG7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc_sd"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3300000>; |
| }; |
| }; |
| |
| wl_18: LDO_REG8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "wl_18"; |
| }; |
| |
| lcd_33: SWITCH_REG1 { |
| regulator-name = "lcd_33"; |
| }; |
| }; |
| }; |
| |
| }; |
| |
| &i2c2 { |
| gsl1680: touchscreen@40 { |
| compatible = "silead,gsl1680"; |
| reg = <0x40>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <RK_PB7 IRQ_TYPE_EDGE_FALLING>; |
| power-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>; |
| touchscreen-size-x = <800>; |
| touchscreen-size-y = <1280>; |
| silead,max-fingers = <5>; |
| }; |
| }; |
| |
| &mmc0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; |
| vmmc-supply = <&vcc_sd>; |
| |
| bus-width = <4>; |
| cap-mmc-highspeed; |
| cap-sd-highspeed; |
| disable-wp; |
| }; |
| |
| &pinctrl { |
| pcfg_output_low: pcfg-output-low { |
| output-low; |
| }; |
| |
| usb { |
| host_vbus_drv: host-vbus-drv { |
| rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| otg_vbus_drv: otg-vbus-drv { |
| rockchip,pins = <2 31 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| |
| &pwm1 { |
| status = "okay"; |
| }; |
| |
| &pwm2 { |
| status = "okay"; |
| }; |
| |
| &pwm3 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| status = "okay"; |
| }; |
| |
| &usbphy { |
| status = "okay"; |
| }; |
| |
| &usb_host { |
| status = "okay"; |
| }; |
| |
| &usb_otg { |
| status = "okay"; |
| }; |
| |
| &wdt { |
| status = "okay"; |
| }; |