| /* |
| * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| /dts-v1/; |
| |
| #include "omap443x.dtsi" |
| #include "elpida_ecb240abacn.dtsi" |
| |
| / { |
| model = "TI OMAP4 SDP board"; |
| compatible = "ti,omap4-sdp", "ti,omap4430", "ti,omap4"; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x40000000>; /* 1 GB */ |
| }; |
| |
| aliases { |
| display0 = &lcd0; |
| display1 = &lcd1; |
| display2 = &hdmi0; |
| }; |
| |
| vdd_eth: fixedregulator-vdd-eth { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&enet_enable_gpio>; |
| |
| compatible = "regulator-fixed"; |
| regulator-name = "VDD_ETH"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>; /* gpio line 48 */ |
| enable-active-high; |
| regulator-boot-on; |
| startup-delay-us = <25000>; |
| }; |
| |
| vbat: fixedregulator-vbat { |
| compatible = "regulator-fixed"; |
| regulator-name = "VBAT"; |
| regulator-min-microvolt = <3750000>; |
| regulator-max-microvolt = <3750000>; |
| regulator-boot-on; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| debug0 { |
| label = "omap4:green:debug0"; |
| gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; /* 61 */ |
| }; |
| |
| debug1 { |
| label = "omap4:green:debug1"; |
| gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>; /* 30 */ |
| }; |
| |
| debug2 { |
| label = "omap4:green:debug2"; |
| gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; /* 7 */ |
| }; |
| |
| debug3 { |
| label = "omap4:green:debug3"; |
| gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* 8 */ |
| }; |
| |
| debug4 { |
| label = "omap4:green:debug4"; |
| gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; /* 50 */ |
| }; |
| |
| user1 { |
| label = "omap4:blue:user"; |
| gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* 169 */ |
| }; |
| |
| user2 { |
| label = "omap4:red:user"; |
| gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>; /* 170 */ |
| }; |
| |
| user3 { |
| label = "omap4:green:user"; |
| gpios = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* 139 */ |
| }; |
| }; |
| |
| pwmleds { |
| compatible = "pwm-leds"; |
| kpad { |
| label = "omap4::keypad"; |
| pwms = <&twl_pwm 0 7812500>; |
| max-brightness = <127>; |
| }; |
| |
| charging { |
| label = "omap4:green:chrg"; |
| pwms = <&twl_pwmled 0 7812500>; |
| max-brightness = <255>; |
| }; |
| }; |
| |
| backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&twl_pwm 1 7812500>; |
| brightness-levels = < |
| 0 10 20 30 40 |
| 50 60 70 80 90 |
| 100 110 120 127 |
| >; |
| default-brightness-level = <13>; |
| }; |
| |
| sound { |
| compatible = "ti,abe-twl6040"; |
| ti,model = "SDP4430"; |
| |
| ti,jack-detection = <1>; |
| ti,mclk-freq = <38400000>; |
| |
| ti,mcpdm = <&mcpdm>; |
| ti,dmic = <&dmic>; |
| |
| ti,twl6040 = <&twl6040>; |
| |
| /* Audio routing */ |
| ti,audio-routing = |
| "Headset Stereophone", "HSOL", |
| "Headset Stereophone", "HSOR", |
| "Earphone Spk", "EP", |
| "Ext Spk", "HFL", |
| "Ext Spk", "HFR", |
| "Line Out", "AUXL", |
| "Line Out", "AUXR", |
| "Vibrator", "VIBRAL", |
| "Vibrator", "VIBRAR", |
| "HSMIC", "Headset Mic", |
| "Headset Mic", "Headset Mic Bias", |
| "MAINMIC", "Main Handset Mic", |
| "Main Handset Mic", "Main Mic Bias", |
| "SUBMIC", "Sub Handset Mic", |
| "Sub Handset Mic", "Main Mic Bias", |
| "AFML", "Line In", |
| "AFMR", "Line In", |
| "DMic", "Digital Mic", |
| "Digital Mic", "Digital Mic1 Bias"; |
| }; |
| |
| /* regulator for wl12xx on sdio5 */ |
| wl12xx_vmmc: wl12xx_vmmc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wl12xx_gpio>; |
| compatible = "regulator-fixed"; |
| regulator-name = "vwl1271"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; |
| startup-delay-us = <70000>; |
| enable-active-high; |
| }; |
| |
| tpd12s015: encoder { |
| compatible = "ti,tpd12s015"; |
| |
| gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */ |
| <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */ |
| <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */ |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| tpd12s015_in: endpoint { |
| remote-endpoint = <&hdmi_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| tpd12s015_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| hdmi0: connector { |
| compatible = "hdmi-connector"; |
| label = "hdmi"; |
| |
| type = "c"; |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&tpd12s015_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &omap4_pmx_core { |
| pinctrl-names = "default"; |
| pinctrl-0 = < |
| &dss_hdmi_pins |
| &tpd12s015_pins |
| >; |
| |
| uart2_pins: pinmux_uart2_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ |
| OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ |
| OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */ |
| OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ |
| >; |
| }; |
| |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ |
| OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ |
| OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ |
| OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ |
| >; |
| }; |
| |
| uart4_pins: pinmux_uart4_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx.uart4_rx */ |
| OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx.uart4_tx */ |
| >; |
| }; |
| |
| twl6040_pins: pinmux_twl6040_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ |
| OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ |
| >; |
| }; |
| |
| mcpdm_pins: pinmux_mcpdm_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ |
| OMAP4_IOPAD(0x108, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ |
| OMAP4_IOPAD(0x10a, PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ |
| OMAP4_IOPAD(0x10c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ |
| OMAP4_IOPAD(0x10e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ |
| >; |
| }; |
| |
| dmic_pins: pinmux_dmic_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x110, PIN_OUTPUT | MUX_MODE0) /* abe_dmic_clk1.abe_dmic_clk1 */ |
| OMAP4_IOPAD(0x112, PIN_INPUT | MUX_MODE0) /* abe_dmic_din1.abe_dmic_din1 */ |
| OMAP4_IOPAD(0x114, PIN_INPUT | MUX_MODE0) /* abe_dmic_din2.abe_dmic_din2 */ |
| OMAP4_IOPAD(0x116, PIN_INPUT | MUX_MODE0) /* abe_dmic_din3.abe_dmic_din3 */ |
| >; |
| }; |
| |
| mcbsp1_pins: pinmux_mcbsp1_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ |
| OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ |
| OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ |
| OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ |
| >; |
| }; |
| |
| mcbsp2_pins: pinmux_mcbsp2_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx.abe_mcbsp2_clkx */ |
| OMAP4_IOPAD(0x0f8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dr.abe_mcbsp2_dr */ |
| OMAP4_IOPAD(0x0fa, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dx.abe_mcbsp2_dx */ |
| OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx.abe_mcbsp2_fsx */ |
| >; |
| }; |
| |
| mcspi1_pins: pinmux_mcspi1_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x132, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ |
| OMAP4_IOPAD(0x134, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ |
| OMAP4_IOPAD(0x136, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ |
| OMAP4_IOPAD(0x138, PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ |
| >; |
| }; |
| |
| dss_hdmi_pins: pinmux_dss_hdmi_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */ |
| OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ |
| OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ |
| >; |
| }; |
| |
| tpd12s015_pins: pinmux_tpd12s015_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ |
| OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ |
| OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ |
| >; |
| }; |
| |
| i2c1_pins: pinmux_i2c1_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ |
| OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ |
| >; |
| }; |
| |
| i2c2_pins: pinmux_i2c2_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ |
| OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ |
| >; |
| }; |
| |
| i2c3_pins: pinmux_i2c3_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ |
| OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ |
| >; |
| }; |
| |
| i2c4_pins: pinmux_i2c4_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ |
| OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ |
| >; |
| }; |
| |
| /* wl12xx GPIO output for WLAN_EN */ |
| wl12xx_gpio: pinmux_wl12xx_gpio { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) /* gpmc_nwp.gpio_54 */ |
| >; |
| }; |
| |
| /* wl12xx GPIO inputs and SDIO pins */ |
| wl12xx_pins: pinmux_wl12xx_pins { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ |
| OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ |
| OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ |
| OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ |
| OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ |
| OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ |
| OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ |
| >; |
| }; |
| |
| /* gpio_48 for ENET_ENABLE */ |
| enet_enable_gpio: pinmux_enet_enable_gpio { |
| pinctrl-single,pins = < |
| OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* gpmc_a24.gpio_48 */ |
| >; |
| }; |
| |
| ks8851_pins: pinmux_ks8851_pins { |
| pinctrl-single,pins = < |
| /* ENET_INT */ |
| OMAP4_IOPAD(0x054, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad10.gpio_34 */ |
| /* |
| * Misterious pin which makes the ethernet working |
| * The legacy board file requested this pin on boot |
| * (ETH_KS8851_QUART) and set it to high, similarly to |
| * the ENET_ENABLE pin. |
| * We could use gpio-hog to keep it high, but let's use |
| * it as a reset GPIO for ks8851. |
| */ |
| OMAP4_IOPAD(0x13a, PIN_OUTPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.gpio_138 */ |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| |
| clock-frequency = <400000>; |
| |
| twl: twl@48 { |
| reg = <0x48>; |
| /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ |
| }; |
| |
| twl6040: twl@4b { |
| compatible = "ti,twl6040"; |
| #clock-cells = <0>; |
| reg = <0x4b>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&twl6040_pins>; |
| |
| /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ |
| interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ |
| ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */ |
| |
| vio-supply = <&v1v8>; |
| v2v1-supply = <&v2v1>; |
| enable-active-high; |
| |
| /* regulators for vibra motor */ |
| vddvibl-supply = <&vbat>; |
| vddvibr-supply = <&vbat>; |
| |
| vibra { |
| /* Vibra driver, motor resistance parameters */ |
| ti,vibldrv-res = <8>; |
| ti,vibrdrv-res = <3>; |
| ti,viblmotor-res = <10>; |
| ti,vibrmotor-res = <10>; |
| }; |
| }; |
| }; |
| |
| #include "twl6030.dtsi" |
| #include "twl6030_omap4.dtsi" |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_pins>; |
| |
| clock-frequency = <400000>; |
| }; |
| |
| &i2c3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_pins>; |
| |
| clock-frequency = <400000>; |
| |
| /* |
| * Temperature Sensor |
| * http://www.ti.com/lit/ds/symlink/tmp105.pdf |
| */ |
| tmp105@48 { |
| compatible = "ti,tmp105"; |
| reg = <0x48>; |
| }; |
| |
| /* |
| * Ambient Light Sensor |
| * http://www.rohm.com/products/databook/sensor/pdf/bh1780gli-e.pdf |
| */ |
| bh1780@29 { |
| compatible = "rohm,bh1780"; |
| reg = <0x29>; |
| }; |
| }; |
| |
| &i2c4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c4_pins>; |
| |
| clock-frequency = <400000>; |
| |
| /* |
| * 3-Axis Digital Compass |
| * http://www.sparkfun.com/datasheets/Sensors/Magneto/HMC5843.pdf |
| */ |
| hmc5843@1e { |
| compatible = "honeywell,hmc5843"; |
| reg = <0x1e>; |
| }; |
| }; |
| |
| &mcspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcspi1_pins>; |
| |
| eth@0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ks8851_pins>; |
| |
| compatible = "ks8851"; |
| spi-max-frequency = <24000000>; |
| reg = <0>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <2 IRQ_TYPE_LEVEL_LOW>; /* gpio line 34 */ |
| vdd-supply = <&vdd_eth>; |
| reset-gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| &mmc1 { |
| vmmc-supply = <&vmmc>; |
| bus-width = <8>; |
| }; |
| |
| &mmc2 { |
| vmmc-supply = <&vaux1>; |
| bus-width = <8>; |
| ti,non-removable; |
| }; |
| |
| &mmc3 { |
| status = "disabled"; |
| }; |
| |
| &mmc4 { |
| status = "disabled"; |
| }; |
| |
| &mmc5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wl12xx_pins>; |
| vmmc-supply = <&wl12xx_vmmc>; |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| wlcore: wlcore@2 { |
| compatible = "ti,wl1281"; |
| reg = <2>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <21 IRQ_TYPE_EDGE_RISING>; /* gpio 53 */ |
| ref-clock-frequency = <26000000>; |
| tcxo-clock-frequency = <26000000>; |
| }; |
| }; |
| |
| &emif1 { |
| cs1-used; |
| device-handle = <&elpida_ECB240ABACN>; |
| }; |
| |
| &emif2 { |
| cs1-used; |
| device-handle = <&elpida_ECB240ABACN>; |
| }; |
| |
| &keypad { |
| keypad,num-rows = <8>; |
| keypad,num-columns = <8>; |
| linux,keymap = <0x00000012 /* KEY_E */ |
| 0x00010013 /* KEY_R */ |
| 0x00020014 /* KEY_T */ |
| 0x00030066 /* KEY_HOME */ |
| 0x0004003f /* KEY_F5 */ |
| 0x000500f0 /* KEY_UNKNOWN */ |
| 0x00060017 /* KEY_I */ |
| 0x0007002a /* KEY_LEFTSHIFT */ |
| 0x01000020 /* KEY_D*/ |
| 0x01010021 /* KEY_F */ |
| 0x01020022 /* KEY_G */ |
| 0x010300e7 /* KEY_SEND */ |
| 0x01040040 /* KEY_F6 */ |
| 0x010500f0 /* KEY_UNKNOWN */ |
| 0x01060025 /* KEY_K */ |
| 0x0107001c /* KEY_ENTER */ |
| 0x0200002d /* KEY_X */ |
| 0x0201002e /* KEY_C */ |
| 0x0202002f /* KEY_V */ |
| 0x0203006b /* KEY_END */ |
| 0x02040041 /* KEY_F7 */ |
| 0x020500f0 /* KEY_UNKNOWN */ |
| 0x02060034 /* KEY_DOT */ |
| 0x0207003a /* KEY_CAPSLOCK */ |
| 0x0300002c /* KEY_Z */ |
| 0x0301004e /* KEY_KPLUS */ |
| 0x03020030 /* KEY_B */ |
| 0x0303003b /* KEY_F1 */ |
| 0x03040042 /* KEY_F8 */ |
| 0x030500f0 /* KEY_UNKNOWN */ |
| 0x03060018 /* KEY_O */ |
| 0x03070039 /* KEY_SPACE */ |
| 0x04000011 /* KEY_W */ |
| 0x04010015 /* KEY_Y */ |
| 0x04020016 /* KEY_U */ |
| 0x0403003c /* KEY_F2 */ |
| 0x04040073 /* KEY_VOLUMEUP */ |
| 0x040500f0 /* KEY_UNKNOWN */ |
| 0x04060026 /* KEY_L */ |
| 0x04070069 /* KEY_LEFT */ |
| 0x0500001f /* KEY_S */ |
| 0x05010023 /* KEY_H */ |
| 0x05020024 /* KEY_J */ |
| 0x0503003d /* KEY_F3 */ |
| 0x05040043 /* KEY_F9 */ |
| 0x05050072 /* KEY_VOLUMEDOWN */ |
| 0x05060032 /* KEY_M */ |
| 0x0507006a /* KEY_RIGHT */ |
| 0x06000010 /* KEY_Q */ |
| 0x0601001e /* KEY_A */ |
| 0x06020031 /* KEY_N */ |
| 0x0603009e /* KEY_BACK */ |
| 0x0604000e /* KEY_BACKSPACE */ |
| 0x060500f0 /* KEY_UNKNOWN */ |
| 0x06060019 /* KEY_P */ |
| 0x06070067 /* KEY_UP */ |
| 0x07000094 /* KEY_PROG1 */ |
| 0x07010095 /* KEY_PROG2 */ |
| 0x070200ca /* KEY_PROG3 */ |
| 0x070300cb /* KEY_PROG4 */ |
| 0x0704003e /* KEY_F4 */ |
| 0x070500f0 /* KEY_UNKNOWN */ |
| 0x07060160 /* KEY_OK */ |
| 0x0707006c>; /* KEY_DOWN */ |
| linux,input-no-autorepeat; |
| }; |
| |
| &uart2 { |
| interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH |
| &omap4_pmx_core OMAP4_UART2_RX>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| }; |
| |
| &uart3 { |
| interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH |
| &omap4_pmx_core OMAP4_UART3_RX>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>; |
| }; |
| |
| &uart4 { |
| interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH |
| &omap4_pmx_core OMAP4_UART4_RX>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart4_pins>; |
| }; |
| |
| &mcbsp1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcbsp1_pins>; |
| status = "okay"; |
| }; |
| |
| &mcbsp2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcbsp2_pins>; |
| status = "okay"; |
| }; |
| |
| &dmic { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&dmic_pins>; |
| status = "okay"; |
| }; |
| |
| &mcpdm { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcpdm_pins>; |
| |
| clocks = <&twl6040>; |
| clock-names = "pdmclk"; |
| |
| status = "okay"; |
| }; |
| |
| &twl_usb_comparator { |
| usb-supply = <&vusb>; |
| }; |
| |
| &usb_otg_hs { |
| interface-type = <1>; |
| mode = <3>; |
| power = <50>; |
| }; |
| |
| &dss { |
| status = "ok"; |
| }; |
| |
| &dsi1 { |
| status = "ok"; |
| vdd-supply = <&vcxio>; |
| |
| port { |
| dsi1_out_ep: endpoint { |
| remote-endpoint = <&lcd0_in>; |
| lanes = <0 1 2 3 4 5>; |
| }; |
| }; |
| |
| lcd0: display { |
| compatible = "tpo,taal", "panel-dsi-cm"; |
| label = "lcd0"; |
| |
| reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */ |
| |
| port { |
| lcd0_in: endpoint { |
| remote-endpoint = <&dsi1_out_ep>; |
| }; |
| }; |
| }; |
| }; |
| |
| &dsi2 { |
| status = "ok"; |
| vdd-supply = <&vcxio>; |
| |
| port { |
| dsi2_out_ep: endpoint { |
| remote-endpoint = <&lcd1_in>; |
| lanes = <0 1 2 3 4 5>; |
| }; |
| }; |
| |
| lcd1: display { |
| compatible = "tpo,taal", "panel-dsi-cm"; |
| label = "lcd1"; |
| |
| reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ |
| |
| port { |
| lcd1_in: endpoint { |
| remote-endpoint = <&dsi2_out_ep>; |
| }; |
| }; |
| }; |
| }; |
| |
| &hdmi { |
| status = "ok"; |
| vdda-supply = <&vdac>; |
| |
| port { |
| hdmi_out: endpoint { |
| remote-endpoint = <&tpd12s015_in>; |
| }; |
| }; |
| }; |