| /* |
| * BSD LICENSE |
| * |
| * Copyright(c) 2015 Broadcom Corporation. All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in |
| * the documentation and/or other materials provided with the |
| * distribution. |
| * * Neither the name of Broadcom Corporation nor the names of its |
| * contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
| * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
| * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
| * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/clock/bcm-nsp.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "brcm,nsp"; |
| model = "Broadcom Northstar Plus SoC"; |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| serial0 = &uart0; |
| serial1 = &uart1; |
| ethernet0 = &amac0; |
| ethernet1 = &amac1; |
| ethernet2 = &amac2; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| next-level-cache = <&L2>; |
| reg = <0x0>; |
| }; |
| |
| cpu1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| next-level-cache = <&L2>; |
| enable-method = "brcm,bcm-nsp-smp"; |
| secondary-boot-reg = <0xffff0fec>; |
| reg = <0x1>; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH |
| GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>; |
| }; |
| |
| mpcore { |
| compatible = "simple-bus"; |
| ranges = <0x00000000 0x19000000 0x00023000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| a9pll: arm_clk@0 { |
| #clock-cells = <0>; |
| compatible = "brcm,nsp-armpll"; |
| clocks = <&osc>; |
| reg = <0x00000 0x1000>; |
| }; |
| |
| timer@20200 { |
| compatible = "arm,cortex-a9-global-timer"; |
| reg = <0x20200 0x100>; |
| interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&periph_clk>; |
| }; |
| |
| twd-timer@20600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0x20600 0x20>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_EDGE_RISING)>; |
| clocks = <&periph_clk>; |
| }; |
| |
| twd-watchdog@20620 { |
| compatible = "arm,cortex-a9-twd-wdt"; |
| reg = <0x20620 0x20>; |
| interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_LEVEL_HIGH)>; |
| clocks = <&periph_clk>; |
| }; |
| |
| gic: interrupt-controller@21000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| interrupt-controller; |
| reg = <0x21000 0x1000>, |
| <0x20100 0x100>; |
| }; |
| |
| L2: l2-cache { |
| compatible = "arm,pl310-cache"; |
| reg = <0x22000 0x1000>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| }; |
| |
| clocks { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| osc: oscillator { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <25000000>; |
| }; |
| |
| iprocmed: iprocmed { |
| #clock-cells = <0>; |
| compatible = "fixed-factor-clock"; |
| clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>; |
| clock-div = <2>; |
| clock-mult = <1>; |
| }; |
| |
| iprocslow: iprocslow { |
| #clock-cells = <0>; |
| compatible = "fixed-factor-clock"; |
| clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>; |
| clock-div = <4>; |
| clock-mult = <1>; |
| }; |
| |
| periph_clk: periph_clk { |
| #clock-cells = <0>; |
| compatible = "fixed-factor-clock"; |
| clocks = <&a9pll>; |
| clock-div = <2>; |
| clock-mult = <1>; |
| }; |
| }; |
| |
| axi { |
| compatible = "simple-bus"; |
| ranges = <0x00000000 0x18000000 0x0011c40c>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| gpioa: gpio@20 { |
| compatible = "brcm,nsp-gpio-a"; |
| reg = <0x0020 0x70>, |
| <0x3f1c4 0x1c>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| ngpios = <32>; |
| interrupt-controller; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-ranges = <&pinctrl 0 0 32>; |
| }; |
| |
| uart0: serial@300 { |
| compatible = "ns16550a"; |
| reg = <0x0300 0x100>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&osc>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@400 { |
| compatible = "ns16550a"; |
| reg = <0x0400 0x100>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&osc>; |
| status = "disabled"; |
| }; |
| |
| dma@20000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x20000 0x1000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&iprocslow>; |
| clock-names = "apb_pclk"; |
| #dma-cells = <1>; |
| }; |
| |
| sdio: sdhci@21000 { |
| compatible = "brcm,sdhci-iproc-cygnus"; |
| reg = <0x21000 0x100>; |
| interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; |
| sdhci,auto-cmd12; |
| clocks = <&lcpll0 BCM_NSP_LCPLL0_SDIO_CLK>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| amac0: ethernet@22000 { |
| compatible = "brcm,nsp-amac"; |
| reg = <0x022000 0x1000>, |
| <0x110000 0x1000>; |
| reg-names = "amac_base", "idm_base"; |
| interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| amac1: ethernet@23000 { |
| compatible = "brcm,nsp-amac"; |
| reg = <0x023000 0x1000>, |
| <0x111000 0x1000>; |
| reg-names = "amac_base", "idm_base"; |
| interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| amac2: ethernet@24000 { |
| compatible = "brcm,nsp-amac"; |
| reg = <0x024000 0x1000>, |
| <0x112000 0x1000>; |
| reg-names = "amac_base", "idm_base"; |
| interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| mailbox: mailbox@25000 { |
| compatible = "brcm,iproc-fa2-mbox"; |
| reg = <0x25000 0x445>; |
| interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>; |
| #mbox-cells = <1>; |
| brcm,rx-status-len = <32>; |
| brcm,use-bcm-hdr; |
| dma-coherent; |
| }; |
| |
| nand: nand@26000 { |
| compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1"; |
| reg = <0x026000 0x600>, |
| <0x11b408 0x600>, |
| <0x026f00 0x20>; |
| reg-names = "nand", "iproc-idm", "iproc-ext"; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| brcm,nand-has-wp; |
| }; |
| |
| qspi: spi@27200 { |
| compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi"; |
| reg = <0x027200 0x184>, |
| <0x027000 0x124>, |
| <0x11c408 0x004>, |
| <0x0273a0 0x01c>; |
| reg-names = "mspi", "bspi", "intr_regs", |
| "intr_status_reg"; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "spi_lr_fullness_reached", |
| "spi_lr_session_aborted", |
| "spi_lr_impatient", |
| "spi_lr_session_done", |
| "spi_lr_overhead", |
| "mspi_done", |
| "mspi_halted"; |
| clocks = <&iprocmed>; |
| clock-names = "iprocmed"; |
| num-cs = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| xhci: usb@29000 { |
| compatible = "generic-xhci"; |
| reg = <0x29000 0x1000>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&usb3_phy>; |
| phy-names = "usb3-phy"; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| ehci0: usb@2a000 { |
| compatible = "generic-ehci"; |
| reg = <0x2a000 0x100>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| ohci0: usb@2b000 { |
| compatible = "generic-ohci"; |
| reg = <0x2b000 0x100>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| crypto@2f000 { |
| compatible = "brcm,spum-nsp-crypto"; |
| reg = <0x2f000 0x900>; |
| mboxes = <&mailbox 0>; |
| }; |
| |
| gpiob: gpio@30000 { |
| compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio"; |
| reg = <0x30000 0x50>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| ngpios = <4>; |
| interrupt-controller; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pwm: pwm@31000 { |
| compatible = "brcm,iproc-pwm"; |
| reg = <0x31000 0x28>; |
| clocks = <&osc>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| rng: rng@33000 { |
| compatible = "brcm,bcm-nsp-rng"; |
| reg = <0x33000 0x14>; |
| }; |
| |
| ccbtimer0: timer@34000 { |
| compatible = "arm,sp804"; |
| reg = <0x34000 0x1000>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&iprocslow>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| ccbtimer1: timer@35000 { |
| compatible = "arm,sp804"; |
| reg = <0x35000 0x1000>; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&iprocslow>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| srab: srab@36000 { |
| compatible = "brcm,nsp-srab"; |
| reg = <0x36000 0x1000>, |
| <0x3f308 0x8>, |
| <0x3f410 0xc>; |
| reg-names = "srab", "mux_config", "sgmii"; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "link_state_p0", |
| "link_state_p1", |
| "link_state_p2", |
| "link_state_p3", |
| "link_state_p4", |
| "link_state_p5", |
| "link_state_p7", |
| "link_state_p8", |
| "phy", |
| "ts", |
| "imp_sleep_timer_p5", |
| "imp_sleep_timer_p7", |
| "imp_sleep_timer_p8"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| /* ports are defined in board DTS */ |
| }; |
| |
| i2c0: i2c@38000 { |
| compatible = "brcm,iproc-i2c"; |
| reg = <0x38000 0x50>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <100000>; |
| dma-coherent; |
| status = "disabled"; |
| }; |
| |
| watchdog@39000 { |
| compatible = "arm,sp805", "arm,primecell"; |
| reg = <0x39000 0x1000>; |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&iprocslow>, <&iprocslow>; |
| clock-names = "wdogclk", "apb_pclk"; |
| }; |
| |
| lcpll0: lcpll0@3f100 { |
| #clock-cells = <1>; |
| compatible = "brcm,nsp-lcpll0"; |
| reg = <0x3f100 0x14>; |
| clocks = <&osc>; |
| clock-output-names = "lcpll0", "pcie_phy", "sdio", |
| "ddr_phy"; |
| }; |
| |
| genpll: genpll@3f140 { |
| #clock-cells = <1>; |
| compatible = "brcm,nsp-genpll"; |
| reg = <0x3f140 0x24>; |
| clocks = <&osc>; |
| clock-output-names = "genpll", "phy", "ethernetclk", |
| "usbclk", "iprocfast", "sata1", |
| "sata2"; |
| }; |
| |
| pinctrl: pinctrl@3f1c0 { |
| compatible = "brcm,nsp-pinmux"; |
| reg = <0x3f1c0 0x04>, |
| <0x30028 0x04>, |
| <0x3f408 0x04>; |
| }; |
| |
| thermal: thermal@3f2c0 { |
| compatible = "brcm,ns-thermal"; |
| reg = <0x3f2c0 0x10>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| sata_phy: sata_phy@40100 { |
| compatible = "brcm,iproc-nsp-sata-phy"; |
| reg = <0x40100 0x340>; |
| reg-names = "phy"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| sata_phy0: sata-phy@0 { |
| reg = <0>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| sata_phy1: sata-phy@1 { |
| reg = <1>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| sata: ahci@41000 { |
| compatible = "brcm,bcm-nsp-ahci"; |
| reg-names = "ahci", "top-ctrl"; |
| reg = <0x41000 0x1000>, <0x40020 0x1c>; |
| interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| dma-coherent; |
| status = "disabled"; |
| |
| sata0: sata-port@0 { |
| reg = <0>; |
| phys = <&sata_phy0>; |
| phy-names = "sata-phy"; |
| }; |
| |
| sata1: sata-port@1 { |
| reg = <1>; |
| phys = <&sata_phy1>; |
| phy-names = "sata-phy"; |
| }; |
| }; |
| |
| usb3_phy: usb3-phy@104000 { |
| compatible = "brcm,ns-bx-usb3-phy"; |
| reg = <0x104000 0x1000>, |
| <0x032000 0x1000>; |
| reg-names = "dmp", "ccb-mii"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pcie0: pcie@18012000 { |
| compatible = "brcm,iproc-pcie"; |
| reg = <0x18012000 0x1000>; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; |
| |
| linux,pci-domain = <0>; |
| |
| bus-range = <0x00 0xff>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| |
| /* Note: The HW does not support I/O resources. So, |
| * only the memory resource range is being specified. |
| */ |
| ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>; |
| |
| dma-coherent; |
| status = "disabled"; |
| |
| msi-parent = <&msi0>; |
| msi0: msi-controller { |
| compatible = "brcm,iproc-msi"; |
| msi-controller; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; |
| brcm,pcie-msi-inten; |
| }; |
| }; |
| |
| pcie1: pcie@18013000 { |
| compatible = "brcm,iproc-pcie"; |
| reg = <0x18013000 0x1000>; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; |
| |
| linux,pci-domain = <1>; |
| |
| bus-range = <0x00 0xff>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| |
| /* Note: The HW does not support I/O resources. So, |
| * only the memory resource range is being specified. |
| */ |
| ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>; |
| |
| dma-coherent; |
| status = "disabled"; |
| |
| msi-parent = <&msi1>; |
| msi1: msi-controller { |
| compatible = "brcm,iproc-msi"; |
| msi-controller; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| brcm,pcie-msi-inten; |
| }; |
| }; |
| |
| pcie2: pcie@18014000 { |
| compatible = "brcm,iproc-pcie"; |
| reg = <0x18014000 0x1000>; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; |
| |
| linux,pci-domain = <2>; |
| |
| bus-range = <0x00 0xff>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| |
| /* Note: The HW does not support I/O resources. So, |
| * only the memory resource range is being specified. |
| */ |
| ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>; |
| |
| dma-coherent; |
| status = "disabled"; |
| |
| msi-parent = <&msi2>; |
| msi2: msi-controller { |
| compatible = "brcm,iproc-msi"; |
| msi-controller; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; |
| brcm,pcie-msi-inten; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <1000>; |
| coefficients = <(-556) 418000>; |
| thermal-sensors = <&thermal>; |
| |
| trips { |
| cpu-crit { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| }; |
| }; |
| }; |
| }; |