diff --git a/Documentation/devicetree/bindings/input/cap1106.txt b/Documentation/devicetree/bindings/input/cap11xx.txt
similarity index 64%
rename from Documentation/devicetree/bindings/input/cap1106.txt
rename to Documentation/devicetree/bindings/input/cap11xx.txt
index 4b46390..7d0a300 100644
--- a/Documentation/devicetree/bindings/input/cap1106.txt
+++ b/Documentation/devicetree/bindings/input/cap11xx.txt
@@ -1,14 +1,16 @@
-Device tree bindings for Microchip CAP1106, 6 channel capacitive touch sensor
+Device tree bindings for Microchip CAP11xx based capacitive touch sensors
 
-The node for this driver must be a child of a I2C controller node, as the
+The node for this device must be a child of a I2C controller node, as the
 device communication via I2C only.
 
 Required properties:
 
-	compatible:		Must be "microchip,cap1106"
+	compatible:		Must contain one of:
+					"microchip,cap1106"
+					"microchip,cap1126"
+					"microchip,cap1188"
 
 	reg:			The I2C slave address of the device.
-				Only 0x28 is valid.
 
 	interrupts:		Property describing the interrupt line the
 				device's ALERT#/CM_IRQ# pin is connected to.
@@ -26,6 +28,10 @@
 				Valid values are 1, 2, 4, and 8.
 				By default, a gain of 1 is set.
 
+	microchip,irq-active-high:	By default the interrupt pin is active low
+				open drain. This property allows using the active
+				high push-pull output.
+
 	linux,keycodes:		Specifies an array of numeric keycode values to
 				be used for the channels. If this property is
 				omitted, KEY_A, KEY_B, etc are used as
@@ -43,11 +49,11 @@
 		autorepeat;
 		microchip,sensor-gain = <2>;
 
-		linux,keycodes = <103		/* KEY_UP */
-				  106		/* KEY_RIGHT */
-				  108		/* KEY_DOWN */
-				  105		/* KEY_LEFT */
-				  109		/* KEY_PAGEDOWN */
-				  104>;		/* KEY_PAGEUP */
+		linux,keycodes = <103>,		/* KEY_UP */
+				 <106>,		/* KEY_RIGHT */
+				 <108>,		/* KEY_DOWN */
+				 <105>,		/* KEY_LEFT */
+				 <109>,		/* KEY_PAGEDOWN */
+				 <104>;		/* KEY_PAGEUP */
 	};
 }
diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt
new file mode 100644
index 0000000..ee3242c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/elan_i2c.txt
@@ -0,0 +1,34 @@
+Elantech I2C Touchpad
+
+Required properties:
+- compatible: must be "elan,ekth3000".
+- reg: I2C address of the chip.
+- interrupt-parent: a phandle for the interrupt controller (see interrupt
+  binding[0]).
+- interrupts: interrupt to which the chip is connected (see interrupt
+  binding[0]).
+
+Optional properties:
+- wakeup-source: touchpad can be used as a wakeup source.
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the device (see
+  pinctrl binding [1]).
+- vcc-supply: a phandle for the regulator supplying 3.3V power.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+	&i2c1 {
+		/* ... */
+
+		touchpad@15 {
+			compatible = "elan,ekth3000";
+			reg = <0x15>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/input/elants_i2c.txt b/Documentation/devicetree/bindings/input/elants_i2c.txt
new file mode 100644
index 0000000..a765232
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/elants_i2c.txt
@@ -0,0 +1,33 @@
+Elantech I2C Touchscreen
+
+Required properties:
+- compatible: must be "elan,ekth3500".
+- reg: I2C address of the chip.
+- interrupt-parent: a phandle for the interrupt controller (see interrupt
+  binding[0]).
+- interrupts: interrupt to which the chip is connected (see interrupt
+  binding[0]).
+
+Optional properties:
+- wakeup-source: touchscreen can be used as a wakeup source.
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the device (see
+  pinctrl binding [1]).
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+	&i2c1 {
+		/* ... */
+
+		touchscreen@10 {
+			compatible = "elan,ekth3500";
+			reg = <0x10>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt
index 5c2c021..a4a38fc 100644
--- a/Documentation/devicetree/bindings/input/gpio-keys.txt
+++ b/Documentation/devicetree/bindings/input/gpio-keys.txt
@@ -10,10 +10,13 @@
 Each button (key) is represented as a sub-node of "gpio-keys":
 Subnode properties:
 
-	- gpios: OF device-tree gpio specification.
 	- label: Descriptive name of the key.
 	- linux,code: Keycode to emit.
 
+Required mutual exclusive subnode-properties:
+	- gpios: OF device-tree gpio specification.
+	- interrupts: the interrupt line for that input
+
 Optional subnode-properties:
 	- linux,input-type: Specify event type this button/key generates.
 	  If not specified defaults to <1> == EV_KEY.
@@ -33,4 +36,9 @@
 				linux,code = <103>;
 				gpios = <&gpio1 0 1>;
 			};
+			button@22 {
+				label = "GPIO Key DOWN";
+				linux,code = <108>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			};
 			...
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 423d474..b1df0ad 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -47,6 +47,7 @@
 dmo	Data Modul AG
 ebv	EBV Elektronik
 edt	Emerging Display Technologies
+elan	Elan Microelectronic Corp.
 emmicro	EM Microelectronic
 energymicro	Silicon Laboratories (formerly Energy Micro AS)
 epcos	EPCOS AG
diff --git a/MAINTAINERS b/MAINTAINERS
index 4aac6c8..68e79da 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4255,6 +4255,12 @@
 S:	Maintained
 F:	drivers/media/usb/go7007/
 
+GOODIX TOUCHSCREEN
+M:	Bastien Nocera <hadess@hadess.net>
+L:	linux-input@vger.kernel.org
+S:	Maintained
+F:	drivers/input/touchscreen/goodix.c
+
 GPIO SUBSYSTEM
 M:	Linus Walleij <linus.walleij@linaro.org>
 M:	Alexandre Courbot <gnurou@gmail.com>
diff --git a/drivers/input/gameport/gameport.c b/drivers/input/gameport/gameport.c
index e29c04e..e853a21 100644
--- a/drivers/input/gameport/gameport.c
+++ b/drivers/input/gameport/gameport.c
@@ -527,14 +527,14 @@
  */
 static void gameport_init_port(struct gameport *gameport)
 {
-	static atomic_t gameport_no = ATOMIC_INIT(0);
+	static atomic_t gameport_no = ATOMIC_INIT(-1);
 
 	__module_get(THIS_MODULE);
 
 	mutex_init(&gameport->drv_mutex);
 	device_initialize(&gameport->dev);
 	dev_set_name(&gameport->dev, "gameport%lu",
-			(unsigned long)atomic_inc_return(&gameport_no) - 1);
+			(unsigned long)atomic_inc_return(&gameport_no));
 	gameport->dev.bus = &gameport_bus;
 	gameport->dev.release = gameport_release_port;
 	if (gameport->parent)
diff --git a/drivers/input/input.c b/drivers/input/input.c
index 0f175f5..04217c2 100644
--- a/drivers/input/input.c
+++ b/drivers/input/input.c
@@ -1775,7 +1775,7 @@
  */
 struct input_dev *input_allocate_device(void)
 {
-	static atomic_t input_no = ATOMIC_INIT(0);
+	static atomic_t input_no = ATOMIC_INIT(-1);
 	struct input_dev *dev;
 
 	dev = kzalloc(sizeof(struct input_dev), GFP_KERNEL);
@@ -1790,7 +1790,7 @@
 		INIT_LIST_HEAD(&dev->node);
 
 		dev_set_name(&dev->dev, "input%lu",
-			     (unsigned long) atomic_inc_return(&input_no) - 1);
+			     (unsigned long)atomic_inc_return(&input_no));
 
 		__module_get(THIS_MODULE);
 	}
diff --git a/drivers/input/joystick/xpad.c b/drivers/input/joystick/xpad.c
index fc55f0d..3aa2f3f 100644
--- a/drivers/input/joystick/xpad.c
+++ b/drivers/input/joystick/xpad.c
@@ -886,8 +886,8 @@
 
 static int xpad_led_probe(struct usb_xpad *xpad)
 {
-	static atomic_t led_seq	= ATOMIC_INIT(0);
-	long led_no;
+	static atomic_t led_seq	= ATOMIC_INIT(-1);
+	unsigned long led_no;
 	struct xpad_led *led;
 	struct led_classdev *led_cdev;
 	int error;
@@ -899,9 +899,9 @@
 	if (!led)
 		return -ENOMEM;
 
-	led_no = (long)atomic_inc_return(&led_seq) - 1;
+	led_no = atomic_inc_return(&led_seq);
 
-	snprintf(led->name, sizeof(led->name), "xpad%ld", led_no);
+	snprintf(led->name, sizeof(led->name), "xpad%lu", led_no);
 	led->xpad = xpad;
 
 	led_cdev = &led->led_cdev;
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index a3958c6..96ee26c5 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -665,14 +665,14 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called cros_ec_keyb.
 
-config KEYBOARD_CAP1106
-	tristate "Microchip CAP1106 touch sensor"
+config KEYBOARD_CAP11XX
+	tristate "Microchip CAP11XX based touch sensors"
 	depends on OF && I2C
 	select REGMAP_I2C
 	help
-	  Say Y here to enable the CAP1106 touch sensor driver.
+	  Say Y here to enable the CAP11XX touch sensor driver.
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called cap1106.
+	  module will be called cap11xx.
 
 endif
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index 0a33456..febafa5 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -11,7 +11,7 @@
 obj-$(CONFIG_KEYBOARD_ATARI)		+= atakbd.o
 obj-$(CONFIG_KEYBOARD_ATKBD)		+= atkbd.o
 obj-$(CONFIG_KEYBOARD_BFIN)		+= bf54x-keys.o
-obj-$(CONFIG_KEYBOARD_CAP1106)		+= cap1106.o
+obj-$(CONFIG_KEYBOARD_CAP11XX)		+= cap11xx.o
 obj-$(CONFIG_KEYBOARD_CLPS711X)		+= clps711x-keypad.o
 obj-$(CONFIG_KEYBOARD_CROS_EC)		+= cros_ec_keyb.o
 obj-$(CONFIG_KEYBOARD_DAVINCI)		+= davinci_keyscan.o
diff --git a/drivers/input/keyboard/amikbd.c b/drivers/input/keyboard/amikbd.c
index d3b8c58..e04a3b4 100644
--- a/drivers/input/keyboard/amikbd.c
+++ b/drivers/input/keyboard/amikbd.c
@@ -45,6 +45,7 @@
 MODULE_DESCRIPTION("Amiga keyboard driver");
 MODULE_LICENSE("GPL");
 
+#ifdef CONFIG_HW_CONSOLE
 static unsigned char amikbd_keycode[0x78] __initdata = {
 	[0]	 = KEY_GRAVE,
 	[1]	 = KEY_1,
@@ -144,6 +145,32 @@
 	[103]	 = KEY_RIGHTMETA
 };
 
+static void __init amikbd_init_console_keymaps(void)
+{
+	/* We can spare 512 bytes on stack for temp_map in init path. */
+	unsigned short temp_map[NR_KEYS];
+	int i, j;
+
+	for (i = 0; i < MAX_NR_KEYMAPS; i++) {
+		if (!key_maps[i])
+			continue;
+		memset(temp_map, 0, sizeof(temp_map));
+		for (j = 0; j < 0x78; j++) {
+			if (!amikbd_keycode[j])
+				continue;
+			temp_map[j] = key_maps[i][amikbd_keycode[j]];
+		}
+		for (j = 0; j < NR_KEYS; j++) {
+			if (!temp_map[j])
+				temp_map[j] = 0xf200;
+		}
+		memcpy(key_maps[i], temp_map, sizeof(temp_map));
+	}
+}
+#else /* !CONFIG_HW_CONSOLE */
+static inline void amikbd_init_console_keymaps(void) {}
+#endif /* !CONFIG_HW_CONSOLE */
+
 static const char *amikbd_messages[8] = {
 	[0] = KERN_ALERT "amikbd: Ctrl-Amiga-Amiga reset warning!!\n",
 	[1] = KERN_WARNING "amikbd: keyboard lost sync\n",
@@ -186,7 +213,7 @@
 static int __init amikbd_probe(struct platform_device *pdev)
 {
 	struct input_dev *dev;
-	int i, j, err;
+	int i, err;
 
 	dev = input_allocate_device();
 	if (!dev) {
@@ -207,22 +234,8 @@
 	for (i = 0; i < 0x78; i++)
 		set_bit(i, dev->keybit);
 
-	for (i = 0; i < MAX_NR_KEYMAPS; i++) {
-		static u_short temp_map[NR_KEYS] __initdata;
-		if (!key_maps[i])
-			continue;
-		memset(temp_map, 0, sizeof(temp_map));
-		for (j = 0; j < 0x78; j++) {
-			if (!amikbd_keycode[j])
-				continue;
-			temp_map[j] = key_maps[i][amikbd_keycode[j]];
-		}
-		for (j = 0; j < NR_KEYS; j++) {
-			if (!temp_map[j])
-				temp_map[j] = 0xf200;
-		}
-		memcpy(key_maps[i], temp_map, sizeof(temp_map));
-	}
+	amikbd_init_console_keymaps();
+
 	ciaa.cra &= ~0x41;	 /* serial data in, turn off TA */
 	err = request_irq(IRQ_AMIGA_CIAA_SP, amikbd_interrupt, 0, "amikbd",
 			  dev);
diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c
index 6f5d795..e27a258 100644
--- a/drivers/input/keyboard/atkbd.c
+++ b/drivers/input/keyboard/atkbd.c
@@ -456,8 +456,9 @@
 
 	keycode = atkbd->keycode[code];
 
-	if (keycode != ATKBD_KEY_NULL)
-		input_event(dev, EV_MSC, MSC_SCAN, code);
+	if (!(atkbd->release && test_bit(code, atkbd->force_release_mask)))
+		if (keycode != ATKBD_KEY_NULL)
+			input_event(dev, EV_MSC, MSC_SCAN, code);
 
 	switch (keycode) {
 	case ATKBD_KEY_NULL:
@@ -511,6 +512,7 @@
 		input_sync(dev);
 
 		if (value && test_bit(code, atkbd->force_release_mask)) {
+			input_event(dev, EV_MSC, MSC_SCAN, code);
 			input_report_key(dev, keycode, 0);
 			input_sync(dev);
 		}
diff --git a/drivers/input/keyboard/cap1106.c b/drivers/input/keyboard/cap1106.c
deleted file mode 100644
index d70b65a..0000000
--- a/drivers/input/keyboard/cap1106.c
+++ /dev/null
@@ -1,341 +0,0 @@
-/*
- * Input driver for Microchip CAP1106, 6 channel capacitive touch sensor
- *
- * http://www.microchip.com/wwwproducts/Devices.aspx?product=CAP1106
- *
- * (c) 2014 Daniel Mack <linux@zonque.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/input.h>
-#include <linux/of_irq.h>
-#include <linux/regmap.h>
-#include <linux/i2c.h>
-#include <linux/gpio/consumer.h>
-
-#define CAP1106_REG_MAIN_CONTROL	0x00
-#define CAP1106_REG_MAIN_CONTROL_GAIN_SHIFT	(6)
-#define CAP1106_REG_MAIN_CONTROL_GAIN_MASK	(0xc0)
-#define CAP1106_REG_MAIN_CONTROL_DLSEEP		BIT(4)
-#define CAP1106_REG_GENERAL_STATUS	0x02
-#define CAP1106_REG_SENSOR_INPUT	0x03
-#define CAP1106_REG_NOISE_FLAG_STATUS	0x0a
-#define CAP1106_REG_SENOR_DELTA(X)	(0x10 + (X))
-#define CAP1106_REG_SENSITIVITY_CONTROL	0x1f
-#define CAP1106_REG_CONFIG		0x20
-#define CAP1106_REG_SENSOR_ENABLE	0x21
-#define CAP1106_REG_SENSOR_CONFIG	0x22
-#define CAP1106_REG_SENSOR_CONFIG2	0x23
-#define CAP1106_REG_SAMPLING_CONFIG	0x24
-#define CAP1106_REG_CALIBRATION		0x26
-#define CAP1106_REG_INT_ENABLE		0x27
-#define CAP1106_REG_REPEAT_RATE		0x28
-#define CAP1106_REG_MT_CONFIG		0x2a
-#define CAP1106_REG_MT_PATTERN_CONFIG	0x2b
-#define CAP1106_REG_MT_PATTERN		0x2d
-#define CAP1106_REG_RECALIB_CONFIG	0x2f
-#define CAP1106_REG_SENSOR_THRESH(X)	(0x30 + (X))
-#define CAP1106_REG_SENSOR_NOISE_THRESH	0x38
-#define CAP1106_REG_STANDBY_CHANNEL	0x40
-#define CAP1106_REG_STANDBY_CONFIG	0x41
-#define CAP1106_REG_STANDBY_SENSITIVITY	0x42
-#define CAP1106_REG_STANDBY_THRESH	0x43
-#define CAP1106_REG_CONFIG2		0x44
-#define CAP1106_REG_SENSOR_BASE_CNT(X)	(0x50 + (X))
-#define CAP1106_REG_SENSOR_CALIB	(0xb1 + (X))
-#define CAP1106_REG_SENSOR_CALIB_LSB1	0xb9
-#define CAP1106_REG_SENSOR_CALIB_LSB2	0xba
-#define CAP1106_REG_PRODUCT_ID		0xfd
-#define CAP1106_REG_MANUFACTURER_ID	0xfe
-#define CAP1106_REG_REVISION		0xff
-
-#define CAP1106_NUM_CHN 6
-#define CAP1106_PRODUCT_ID	0x55
-#define CAP1106_MANUFACTURER_ID	0x5d
-
-struct cap1106_priv {
-	struct regmap *regmap;
-	struct input_dev *idev;
-
-	/* config */
-	unsigned short keycodes[CAP1106_NUM_CHN];
-};
-
-static const struct reg_default cap1106_reg_defaults[] = {
-	{ CAP1106_REG_MAIN_CONTROL,		0x00 },
-	{ CAP1106_REG_GENERAL_STATUS,		0x00 },
-	{ CAP1106_REG_SENSOR_INPUT,		0x00 },
-	{ CAP1106_REG_NOISE_FLAG_STATUS,	0x00 },
-	{ CAP1106_REG_SENSITIVITY_CONTROL,	0x2f },
-	{ CAP1106_REG_CONFIG,			0x20 },
-	{ CAP1106_REG_SENSOR_ENABLE,		0x3f },
-	{ CAP1106_REG_SENSOR_CONFIG,		0xa4 },
-	{ CAP1106_REG_SENSOR_CONFIG2,		0x07 },
-	{ CAP1106_REG_SAMPLING_CONFIG,		0x39 },
-	{ CAP1106_REG_CALIBRATION,		0x00 },
-	{ CAP1106_REG_INT_ENABLE,		0x3f },
-	{ CAP1106_REG_REPEAT_RATE,		0x3f },
-	{ CAP1106_REG_MT_CONFIG,		0x80 },
-	{ CAP1106_REG_MT_PATTERN_CONFIG,	0x00 },
-	{ CAP1106_REG_MT_PATTERN,		0x3f },
-	{ CAP1106_REG_RECALIB_CONFIG,		0x8a },
-	{ CAP1106_REG_SENSOR_THRESH(0),		0x40 },
-	{ CAP1106_REG_SENSOR_THRESH(1),		0x40 },
-	{ CAP1106_REG_SENSOR_THRESH(2),		0x40 },
-	{ CAP1106_REG_SENSOR_THRESH(3),		0x40 },
-	{ CAP1106_REG_SENSOR_THRESH(4),		0x40 },
-	{ CAP1106_REG_SENSOR_THRESH(5),		0x40 },
-	{ CAP1106_REG_SENSOR_NOISE_THRESH,	0x01 },
-	{ CAP1106_REG_STANDBY_CHANNEL,		0x00 },
-	{ CAP1106_REG_STANDBY_CONFIG,		0x39 },
-	{ CAP1106_REG_STANDBY_SENSITIVITY,	0x02 },
-	{ CAP1106_REG_STANDBY_THRESH,		0x40 },
-	{ CAP1106_REG_CONFIG2,			0x40 },
-	{ CAP1106_REG_SENSOR_CALIB_LSB1,	0x00 },
-	{ CAP1106_REG_SENSOR_CALIB_LSB2,	0x00 },
-};
-
-static bool cap1106_volatile_reg(struct device *dev, unsigned int reg)
-{
-	switch (reg) {
-	case CAP1106_REG_MAIN_CONTROL:
-	case CAP1106_REG_SENSOR_INPUT:
-	case CAP1106_REG_SENOR_DELTA(0):
-	case CAP1106_REG_SENOR_DELTA(1):
-	case CAP1106_REG_SENOR_DELTA(2):
-	case CAP1106_REG_SENOR_DELTA(3):
-	case CAP1106_REG_SENOR_DELTA(4):
-	case CAP1106_REG_SENOR_DELTA(5):
-	case CAP1106_REG_PRODUCT_ID:
-	case CAP1106_REG_MANUFACTURER_ID:
-	case CAP1106_REG_REVISION:
-		return true;
-	}
-
-	return false;
-}
-
-static const struct regmap_config cap1106_regmap_config = {
-	.reg_bits = 8,
-	.val_bits = 8,
-
-	.max_register = CAP1106_REG_REVISION,
-	.reg_defaults = cap1106_reg_defaults,
-
-	.num_reg_defaults = ARRAY_SIZE(cap1106_reg_defaults),
-	.cache_type = REGCACHE_RBTREE,
-	.volatile_reg = cap1106_volatile_reg,
-};
-
-static irqreturn_t cap1106_thread_func(int irq_num, void *data)
-{
-	struct cap1106_priv *priv = data;
-	unsigned int status;
-	int ret, i;
-
-	/*
-	 * Deassert interrupt. This needs to be done before reading the status
-	 * registers, which will not carry valid values otherwise.
-	 */
-	ret = regmap_update_bits(priv->regmap, CAP1106_REG_MAIN_CONTROL, 1, 0);
-	if (ret < 0)
-		goto out;
-
-	ret = regmap_read(priv->regmap, CAP1106_REG_SENSOR_INPUT, &status);
-	if (ret < 0)
-		goto out;
-
-	for (i = 0; i < CAP1106_NUM_CHN; i++)
-		input_report_key(priv->idev, priv->keycodes[i],
-				 status & (1 << i));
-
-	input_sync(priv->idev);
-
-out:
-	return IRQ_HANDLED;
-}
-
-static int cap1106_set_sleep(struct cap1106_priv *priv, bool sleep)
-{
-	return regmap_update_bits(priv->regmap, CAP1106_REG_MAIN_CONTROL,
-				  CAP1106_REG_MAIN_CONTROL_DLSEEP,
-				  sleep ? CAP1106_REG_MAIN_CONTROL_DLSEEP : 0);
-}
-
-static int cap1106_input_open(struct input_dev *idev)
-{
-	struct cap1106_priv *priv = input_get_drvdata(idev);
-
-	return cap1106_set_sleep(priv, false);
-}
-
-static void cap1106_input_close(struct input_dev *idev)
-{
-	struct cap1106_priv *priv = input_get_drvdata(idev);
-
-	cap1106_set_sleep(priv, true);
-}
-
-static int cap1106_i2c_probe(struct i2c_client *i2c_client,
-			     const struct i2c_device_id *id)
-{
-	struct device *dev = &i2c_client->dev;
-	struct cap1106_priv *priv;
-	struct device_node *node;
-	int i, error, irq, gain = 0;
-	unsigned int val, rev;
-	u32 gain32, keycodes[CAP1106_NUM_CHN];
-
-	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-
-	priv->regmap = devm_regmap_init_i2c(i2c_client, &cap1106_regmap_config);
-	if (IS_ERR(priv->regmap))
-		return PTR_ERR(priv->regmap);
-
-	error = regmap_read(priv->regmap, CAP1106_REG_PRODUCT_ID, &val);
-	if (error)
-		return error;
-
-	if (val != CAP1106_PRODUCT_ID) {
-		dev_err(dev, "Product ID: Got 0x%02x, expected 0x%02x\n",
-			val, CAP1106_PRODUCT_ID);
-		return -ENODEV;
-	}
-
-	error = regmap_read(priv->regmap, CAP1106_REG_MANUFACTURER_ID, &val);
-	if (error)
-		return error;
-
-	if (val != CAP1106_MANUFACTURER_ID) {
-		dev_err(dev, "Manufacturer ID: Got 0x%02x, expected 0x%02x\n",
-			val, CAP1106_MANUFACTURER_ID);
-		return -ENODEV;
-	}
-
-	error = regmap_read(priv->regmap, CAP1106_REG_REVISION, &rev);
-	if (error < 0)
-		return error;
-
-	dev_info(dev, "CAP1106 detected, revision 0x%02x\n", rev);
-	i2c_set_clientdata(i2c_client, priv);
-	node = dev->of_node;
-
-	if (!of_property_read_u32(node, "microchip,sensor-gain", &gain32)) {
-		if (is_power_of_2(gain32) && gain32 <= 8)
-			gain = ilog2(gain32);
-		else
-			dev_err(dev, "Invalid sensor-gain value %d\n", gain32);
-	}
-
-	BUILD_BUG_ON(ARRAY_SIZE(keycodes) != ARRAY_SIZE(priv->keycodes));
-
-	/* Provide some useful defaults */
-	for (i = 0; i < ARRAY_SIZE(keycodes); i++)
-		keycodes[i] = KEY_A + i;
-
-	of_property_read_u32_array(node, "linux,keycodes",
-				   keycodes, ARRAY_SIZE(keycodes));
-
-	for (i = 0; i < ARRAY_SIZE(keycodes); i++)
-		priv->keycodes[i] = keycodes[i];
-
-	error = regmap_update_bits(priv->regmap, CAP1106_REG_MAIN_CONTROL,
-				   CAP1106_REG_MAIN_CONTROL_GAIN_MASK,
-				   gain << CAP1106_REG_MAIN_CONTROL_GAIN_SHIFT);
-	if (error)
-		return error;
-
-	/* Disable autorepeat. The Linux input system has its own handling. */
-	error = regmap_write(priv->regmap, CAP1106_REG_REPEAT_RATE, 0);
-	if (error)
-		return error;
-
-	priv->idev = devm_input_allocate_device(dev);
-	if (!priv->idev)
-		return -ENOMEM;
-
-	priv->idev->name = "CAP1106 capacitive touch sensor";
-	priv->idev->id.bustype = BUS_I2C;
-	priv->idev->evbit[0] = BIT_MASK(EV_KEY);
-
-	if (of_property_read_bool(node, "autorepeat"))
-		__set_bit(EV_REP, priv->idev->evbit);
-
-	for (i = 0; i < CAP1106_NUM_CHN; i++)
-		__set_bit(priv->keycodes[i], priv->idev->keybit);
-
-	__clear_bit(KEY_RESERVED, priv->idev->keybit);
-
-	priv->idev->keycode = priv->keycodes;
-	priv->idev->keycodesize = sizeof(priv->keycodes[0]);
-	priv->idev->keycodemax = ARRAY_SIZE(priv->keycodes);
-
-	priv->idev->id.vendor = CAP1106_MANUFACTURER_ID;
-	priv->idev->id.product = CAP1106_PRODUCT_ID;
-	priv->idev->id.version = rev;
-
-	priv->idev->open = cap1106_input_open;
-	priv->idev->close = cap1106_input_close;
-
-	input_set_drvdata(priv->idev, priv);
-
-	/*
-	 * Put the device in deep sleep mode for now.
-	 * ->open() will bring it back once the it is actually needed.
-	 */
-	cap1106_set_sleep(priv, true);
-
-	error = input_register_device(priv->idev);
-	if (error)
-		return error;
-
-	irq = irq_of_parse_and_map(node, 0);
-	if (!irq) {
-		dev_err(dev, "Unable to parse or map IRQ\n");
-		return -ENXIO;
-	}
-
-	error = devm_request_threaded_irq(dev, irq, NULL, cap1106_thread_func,
-					  IRQF_ONESHOT, dev_name(dev), priv);
-	if (error)
-		return error;
-
-	return 0;
-}
-
-static const struct of_device_id cap1106_dt_ids[] = {
-	{ .compatible = "microchip,cap1106", },
-	{}
-};
-MODULE_DEVICE_TABLE(of, cap1106_dt_ids);
-
-static const struct i2c_device_id cap1106_i2c_ids[] = {
-	{ "cap1106", 0 },
-	{}
-};
-MODULE_DEVICE_TABLE(i2c, cap1106_i2c_ids);
-
-static struct i2c_driver cap1106_i2c_driver = {
-	.driver = {
-		.name	= "cap1106",
-		.owner	= THIS_MODULE,
-		.of_match_table = cap1106_dt_ids,
-	},
-	.id_table	= cap1106_i2c_ids,
-	.probe		= cap1106_i2c_probe,
-};
-
-module_i2c_driver(cap1106_i2c_driver);
-
-MODULE_ALIAS("platform:cap1106");
-MODULE_DESCRIPTION("Microchip CAP1106 driver");
-MODULE_AUTHOR("Daniel Mack <linux@zonque.org>");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
new file mode 100644
index 0000000..4f59f0b
--- /dev/null
+++ b/drivers/input/keyboard/cap11xx.c
@@ -0,0 +1,376 @@
+/*
+ * Input driver for Microchip CAP11xx based capacitive touch sensors
+ *
+ * (c) 2014 Daniel Mack <linux@zonque.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+#include <linux/i2c.h>
+#include <linux/gpio/consumer.h>
+
+#define CAP11XX_REG_MAIN_CONTROL	0x00
+#define CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT	(6)
+#define CAP11XX_REG_MAIN_CONTROL_GAIN_MASK	(0xc0)
+#define CAP11XX_REG_MAIN_CONTROL_DLSEEP		BIT(4)
+#define CAP11XX_REG_GENERAL_STATUS	0x02
+#define CAP11XX_REG_SENSOR_INPUT	0x03
+#define CAP11XX_REG_NOISE_FLAG_STATUS	0x0a
+#define CAP11XX_REG_SENOR_DELTA(X)	(0x10 + (X))
+#define CAP11XX_REG_SENSITIVITY_CONTROL	0x1f
+#define CAP11XX_REG_CONFIG		0x20
+#define CAP11XX_REG_SENSOR_ENABLE	0x21
+#define CAP11XX_REG_SENSOR_CONFIG	0x22
+#define CAP11XX_REG_SENSOR_CONFIG2	0x23
+#define CAP11XX_REG_SAMPLING_CONFIG	0x24
+#define CAP11XX_REG_CALIBRATION		0x26
+#define CAP11XX_REG_INT_ENABLE		0x27
+#define CAP11XX_REG_REPEAT_RATE		0x28
+#define CAP11XX_REG_MT_CONFIG		0x2a
+#define CAP11XX_REG_MT_PATTERN_CONFIG	0x2b
+#define CAP11XX_REG_MT_PATTERN		0x2d
+#define CAP11XX_REG_RECALIB_CONFIG	0x2f
+#define CAP11XX_REG_SENSOR_THRESH(X)	(0x30 + (X))
+#define CAP11XX_REG_SENSOR_NOISE_THRESH	0x38
+#define CAP11XX_REG_STANDBY_CHANNEL	0x40
+#define CAP11XX_REG_STANDBY_CONFIG	0x41
+#define CAP11XX_REG_STANDBY_SENSITIVITY	0x42
+#define CAP11XX_REG_STANDBY_THRESH	0x43
+#define CAP11XX_REG_CONFIG2		0x44
+#define CAP11XX_REG_CONFIG2_ALT_POL	BIT(6)
+#define CAP11XX_REG_SENSOR_BASE_CNT(X)	(0x50 + (X))
+#define CAP11XX_REG_SENSOR_CALIB	(0xb1 + (X))
+#define CAP11XX_REG_SENSOR_CALIB_LSB1	0xb9
+#define CAP11XX_REG_SENSOR_CALIB_LSB2	0xba
+#define CAP11XX_REG_PRODUCT_ID		0xfd
+#define CAP11XX_REG_MANUFACTURER_ID	0xfe
+#define CAP11XX_REG_REVISION		0xff
+
+#define CAP11XX_MANUFACTURER_ID	0x5d
+
+struct cap11xx_priv {
+	struct regmap *regmap;
+	struct input_dev *idev;
+
+	/* config */
+	u32 keycodes[];
+};
+
+struct cap11xx_hw_model {
+	u8 product_id;
+	unsigned int num_channels;
+};
+
+enum {
+	CAP1106,
+	CAP1126,
+	CAP1188,
+};
+
+static const struct cap11xx_hw_model cap11xx_devices[] = {
+	[CAP1106] = { .product_id = 0x55, .num_channels = 6 },
+	[CAP1126] = { .product_id = 0x53, .num_channels = 6 },
+	[CAP1188] = { .product_id = 0x50, .num_channels = 8 },
+};
+
+static const struct reg_default cap11xx_reg_defaults[] = {
+	{ CAP11XX_REG_MAIN_CONTROL,		0x00 },
+	{ CAP11XX_REG_GENERAL_STATUS,		0x00 },
+	{ CAP11XX_REG_SENSOR_INPUT,		0x00 },
+	{ CAP11XX_REG_NOISE_FLAG_STATUS,	0x00 },
+	{ CAP11XX_REG_SENSITIVITY_CONTROL,	0x2f },
+	{ CAP11XX_REG_CONFIG,			0x20 },
+	{ CAP11XX_REG_SENSOR_ENABLE,		0x3f },
+	{ CAP11XX_REG_SENSOR_CONFIG,		0xa4 },
+	{ CAP11XX_REG_SENSOR_CONFIG2,		0x07 },
+	{ CAP11XX_REG_SAMPLING_CONFIG,		0x39 },
+	{ CAP11XX_REG_CALIBRATION,		0x00 },
+	{ CAP11XX_REG_INT_ENABLE,		0x3f },
+	{ CAP11XX_REG_REPEAT_RATE,		0x3f },
+	{ CAP11XX_REG_MT_CONFIG,		0x80 },
+	{ CAP11XX_REG_MT_PATTERN_CONFIG,	0x00 },
+	{ CAP11XX_REG_MT_PATTERN,		0x3f },
+	{ CAP11XX_REG_RECALIB_CONFIG,		0x8a },
+	{ CAP11XX_REG_SENSOR_THRESH(0),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(1),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(2),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(3),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(4),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(5),		0x40 },
+	{ CAP11XX_REG_SENSOR_NOISE_THRESH,	0x01 },
+	{ CAP11XX_REG_STANDBY_CHANNEL,		0x00 },
+	{ CAP11XX_REG_STANDBY_CONFIG,		0x39 },
+	{ CAP11XX_REG_STANDBY_SENSITIVITY,	0x02 },
+	{ CAP11XX_REG_STANDBY_THRESH,		0x40 },
+	{ CAP11XX_REG_CONFIG2,			0x40 },
+	{ CAP11XX_REG_SENSOR_CALIB_LSB1,	0x00 },
+	{ CAP11XX_REG_SENSOR_CALIB_LSB2,	0x00 },
+};
+
+static bool cap11xx_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case CAP11XX_REG_MAIN_CONTROL:
+	case CAP11XX_REG_SENSOR_INPUT:
+	case CAP11XX_REG_SENOR_DELTA(0):
+	case CAP11XX_REG_SENOR_DELTA(1):
+	case CAP11XX_REG_SENOR_DELTA(2):
+	case CAP11XX_REG_SENOR_DELTA(3):
+	case CAP11XX_REG_SENOR_DELTA(4):
+	case CAP11XX_REG_SENOR_DELTA(5):
+	case CAP11XX_REG_PRODUCT_ID:
+	case CAP11XX_REG_MANUFACTURER_ID:
+	case CAP11XX_REG_REVISION:
+		return true;
+	}
+
+	return false;
+}
+
+static const struct regmap_config cap11xx_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = CAP11XX_REG_REVISION,
+	.reg_defaults = cap11xx_reg_defaults,
+
+	.num_reg_defaults = ARRAY_SIZE(cap11xx_reg_defaults),
+	.cache_type = REGCACHE_RBTREE,
+	.volatile_reg = cap11xx_volatile_reg,
+};
+
+static irqreturn_t cap11xx_thread_func(int irq_num, void *data)
+{
+	struct cap11xx_priv *priv = data;
+	unsigned int status;
+	int ret, i;
+
+	/*
+	 * Deassert interrupt. This needs to be done before reading the status
+	 * registers, which will not carry valid values otherwise.
+	 */
+	ret = regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL, 1, 0);
+	if (ret < 0)
+		goto out;
+
+	ret = regmap_read(priv->regmap, CAP11XX_REG_SENSOR_INPUT, &status);
+	if (ret < 0)
+		goto out;
+
+	for (i = 0; i < priv->idev->keycodemax; i++)
+		input_report_key(priv->idev, priv->keycodes[i],
+				 status & (1 << i));
+
+	input_sync(priv->idev);
+
+out:
+	return IRQ_HANDLED;
+}
+
+static int cap11xx_set_sleep(struct cap11xx_priv *priv, bool sleep)
+{
+	return regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL,
+				  CAP11XX_REG_MAIN_CONTROL_DLSEEP,
+				  sleep ? CAP11XX_REG_MAIN_CONTROL_DLSEEP : 0);
+}
+
+static int cap11xx_input_open(struct input_dev *idev)
+{
+	struct cap11xx_priv *priv = input_get_drvdata(idev);
+
+	return cap11xx_set_sleep(priv, false);
+}
+
+static void cap11xx_input_close(struct input_dev *idev)
+{
+	struct cap11xx_priv *priv = input_get_drvdata(idev);
+
+	cap11xx_set_sleep(priv, true);
+}
+
+static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
+			     const struct i2c_device_id *id)
+{
+	struct device *dev = &i2c_client->dev;
+	struct cap11xx_priv *priv;
+	struct device_node *node;
+	const struct cap11xx_hw_model *cap;
+	int i, error, irq, gain = 0;
+	unsigned int val, rev;
+	u32 gain32;
+
+	if (id->driver_data >= ARRAY_SIZE(cap11xx_devices)) {
+		dev_err(dev, "Invalid device ID %lu\n", id->driver_data);
+		return -EINVAL;
+	}
+
+	cap = &cap11xx_devices[id->driver_data];
+	if (!cap || !cap->num_channels) {
+		dev_err(dev, "Invalid device configuration\n");
+		return -EINVAL;
+	}
+
+	priv = devm_kzalloc(dev,
+			    sizeof(*priv) +
+				cap->num_channels * sizeof(priv->keycodes[0]),
+			    GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->regmap = devm_regmap_init_i2c(i2c_client, &cap11xx_regmap_config);
+	if (IS_ERR(priv->regmap))
+		return PTR_ERR(priv->regmap);
+
+	error = regmap_read(priv->regmap, CAP11XX_REG_PRODUCT_ID, &val);
+	if (error)
+		return error;
+
+	if (val != cap->product_id) {
+		dev_err(dev, "Product ID: Got 0x%02x, expected 0x%02x\n",
+			val, cap->product_id);
+		return -ENXIO;
+	}
+
+	error = regmap_read(priv->regmap, CAP11XX_REG_MANUFACTURER_ID, &val);
+	if (error)
+		return error;
+
+	if (val != CAP11XX_MANUFACTURER_ID) {
+		dev_err(dev, "Manufacturer ID: Got 0x%02x, expected 0x%02x\n",
+			val, CAP11XX_MANUFACTURER_ID);
+		return -ENXIO;
+	}
+
+	error = regmap_read(priv->regmap, CAP11XX_REG_REVISION, &rev);
+	if (error < 0)
+		return error;
+
+	dev_info(dev, "CAP11XX detected, revision 0x%02x\n", rev);
+	i2c_set_clientdata(i2c_client, priv);
+	node = dev->of_node;
+
+	if (!of_property_read_u32(node, "microchip,sensor-gain", &gain32)) {
+		if (is_power_of_2(gain32) && gain32 <= 8)
+			gain = ilog2(gain32);
+		else
+			dev_err(dev, "Invalid sensor-gain value %d\n", gain32);
+	}
+
+	if (of_property_read_bool(node, "microchip,irq-active-high")) {
+		error = regmap_update_bits(priv->regmap, CAP11XX_REG_CONFIG2,
+					   CAP11XX_REG_CONFIG2_ALT_POL, 0);
+		if (error)
+			return error;
+	}
+
+	/* Provide some useful defaults */
+	for (i = 0; i < cap->num_channels; i++)
+		priv->keycodes[i] = KEY_A + i;
+
+	of_property_read_u32_array(node, "linux,keycodes",
+				   priv->keycodes, cap->num_channels);
+
+	error = regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL,
+				   CAP11XX_REG_MAIN_CONTROL_GAIN_MASK,
+				   gain << CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT);
+	if (error)
+		return error;
+
+	/* Disable autorepeat. The Linux input system has its own handling. */
+	error = regmap_write(priv->regmap, CAP11XX_REG_REPEAT_RATE, 0);
+	if (error)
+		return error;
+
+	priv->idev = devm_input_allocate_device(dev);
+	if (!priv->idev)
+		return -ENOMEM;
+
+	priv->idev->name = "CAP11XX capacitive touch sensor";
+	priv->idev->id.bustype = BUS_I2C;
+	priv->idev->evbit[0] = BIT_MASK(EV_KEY);
+
+	if (of_property_read_bool(node, "autorepeat"))
+		__set_bit(EV_REP, priv->idev->evbit);
+
+	for (i = 0; i < cap->num_channels; i++)
+		__set_bit(priv->keycodes[i], priv->idev->keybit);
+
+	__clear_bit(KEY_RESERVED, priv->idev->keybit);
+
+	priv->idev->keycode = priv->keycodes;
+	priv->idev->keycodesize = sizeof(priv->keycodes[0]);
+	priv->idev->keycodemax = cap->num_channels;
+
+	priv->idev->id.vendor = CAP11XX_MANUFACTURER_ID;
+	priv->idev->id.product = cap->product_id;
+	priv->idev->id.version = rev;
+
+	priv->idev->open = cap11xx_input_open;
+	priv->idev->close = cap11xx_input_close;
+
+	input_set_drvdata(priv->idev, priv);
+
+	/*
+	 * Put the device in deep sleep mode for now.
+	 * ->open() will bring it back once the it is actually needed.
+	 */
+	cap11xx_set_sleep(priv, true);
+
+	error = input_register_device(priv->idev);
+	if (error)
+		return error;
+
+	irq = irq_of_parse_and_map(node, 0);
+	if (!irq) {
+		dev_err(dev, "Unable to parse or map IRQ\n");
+		return -ENXIO;
+	}
+
+	error = devm_request_threaded_irq(dev, irq, NULL, cap11xx_thread_func,
+					  IRQF_ONESHOT, dev_name(dev), priv);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static const struct of_device_id cap11xx_dt_ids[] = {
+	{ .compatible = "microchip,cap1106", },
+	{ .compatible = "microchip,cap1126", },
+	{ .compatible = "microchip,cap1188", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, cap11xx_dt_ids);
+
+static const struct i2c_device_id cap11xx_i2c_ids[] = {
+	{ "cap1106", CAP1106 },
+	{ "cap1126", CAP1126 },
+	{ "cap1188", CAP1188 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, cap11xx_i2c_ids);
+
+static struct i2c_driver cap11xx_i2c_driver = {
+	.driver = {
+		.name	= "cap11xx",
+		.owner	= THIS_MODULE,
+		.of_match_table = cap11xx_dt_ids,
+	},
+	.id_table	= cap11xx_i2c_ids,
+	.probe		= cap11xx_i2c_probe,
+};
+
+module_i2c_driver(cap11xx_i2c_driver);
+
+MODULE_ALIAS("platform:cap11xx");
+MODULE_DESCRIPTION("Microchip CAP11XX driver");
+MODULE_AUTHOR("Daniel Mack <linux@zonque.org>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/keyboard/gpio_keys.c b/drivers/input/keyboard/gpio_keys.c
index 8f3a24e..d4dd78a 100644
--- a/drivers/input/keyboard/gpio_keys.c
+++ b/drivers/input/keyboard/gpio_keys.c
@@ -29,6 +29,7 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
+#include <linux/of_irq.h>
 #include <linux/spinlock.h>
 
 struct gpio_button_data {
@@ -617,27 +618,31 @@
 
 	i = 0;
 	for_each_child_of_node(node, pp) {
-		int gpio;
+		int gpio = -1;
 		enum of_gpio_flags flags;
 
-		if (!of_find_property(pp, "gpios", NULL)) {
-			pdata->nbuttons--;
-			dev_warn(dev, "Found button without gpios\n");
-			continue;
-		}
-
-		gpio = of_get_gpio_flags(pp, 0, &flags);
-		if (gpio < 0) {
-			error = gpio;
-			if (error != -EPROBE_DEFER)
-				dev_err(dev,
-					"Failed to get gpio flags, error: %d\n",
-					error);
-			return ERR_PTR(error);
-		}
-
 		button = &pdata->buttons[i++];
 
+		if (!of_find_property(pp, "gpios", NULL)) {
+			button->irq = irq_of_parse_and_map(pp, 0);
+			if (button->irq == 0) {
+				i--;
+				pdata->nbuttons--;
+				dev_warn(dev, "Found button without gpios or irqs\n");
+				continue;
+			}
+		} else {
+			gpio = of_get_gpio_flags(pp, 0, &flags);
+			if (gpio < 0) {
+				error = gpio;
+				if (error != -EPROBE_DEFER)
+					dev_err(dev,
+						"Failed to get gpio flags, error: %d\n",
+						error);
+				return ERR_PTR(error);
+			}
+		}
+
 		button->gpio = gpio;
 		button->active_low = flags & OF_GPIO_ACTIVE_LOW;
 
diff --git a/drivers/input/keyboard/lm8323.c b/drivers/input/keyboard/lm8323.c
index cb32e2b..21bea52 100644
--- a/drivers/input/keyboard/lm8323.c
+++ b/drivers/input/keyboard/lm8323.c
@@ -616,6 +616,8 @@
 	unsigned int i;
 
 	ret = kstrtouint(buf, 10, &i);
+	if (ret)
+		return ret;
 
 	mutex_lock(&lm->lock);
 	lm->kp_enabled = !i;
diff --git a/drivers/input/keyboard/lpc32xx-keys.c b/drivers/input/keyboard/lpc32xx-keys.c
index 8c07937..265d641 100644
--- a/drivers/input/keyboard/lpc32xx-keys.c
+++ b/drivers/input/keyboard/lpc32xx-keys.c
@@ -66,7 +66,6 @@
 struct lpc32xx_kscan_drv {
 	struct input_dev *input;
 	struct clk *clk;
-	struct resource *iores;
 	void __iomem *kscan_base;
 	unsigned int irq;
 
@@ -188,32 +187,27 @@
 		return -EINVAL;
 	}
 
-	kscandat = kzalloc(sizeof(struct lpc32xx_kscan_drv), GFP_KERNEL);
-	if (!kscandat) {
-		dev_err(&pdev->dev, "failed to allocate memory\n");
+	kscandat = devm_kzalloc(&pdev->dev, sizeof(*kscandat),
+				GFP_KERNEL);
+	if (!kscandat)
 		return -ENOMEM;
-	}
 
 	error = lpc32xx_parse_dt(&pdev->dev, kscandat);
 	if (error) {
 		dev_err(&pdev->dev, "failed to parse device tree\n");
-		goto err_free_mem;
+		return error;
 	}
 
 	keymap_size = sizeof(kscandat->keymap[0]) *
 				(kscandat->matrix_sz << kscandat->row_shift);
-	kscandat->keymap = kzalloc(keymap_size, GFP_KERNEL);
-	if (!kscandat->keymap) {
-		dev_err(&pdev->dev, "could not allocate memory for keymap\n");
-		error = -ENOMEM;
-		goto err_free_mem;
-	}
+	kscandat->keymap = devm_kzalloc(&pdev->dev, keymap_size, GFP_KERNEL);
+	if (!kscandat->keymap)
+		return -ENOMEM;
 
-	kscandat->input = input = input_allocate_device();
+	kscandat->input = input = devm_input_allocate_device(&pdev->dev);
 	if (!input) {
 		dev_err(&pdev->dev, "failed to allocate input device\n");
-		error = -ENOMEM;
-		goto err_free_keymap;
+		return -ENOMEM;
 	}
 
 	/* Setup key input */
@@ -234,39 +228,26 @@
 					   kscandat->keymap, kscandat->input);
 	if (error) {
 		dev_err(&pdev->dev, "failed to build keymap\n");
-		goto err_free_input;
+		return error;
 	}
 
 	input_set_drvdata(kscandat->input, kscandat);
 
-	kscandat->iores = request_mem_region(res->start, resource_size(res),
-					     pdev->name);
-	if (!kscandat->iores) {
-		dev_err(&pdev->dev, "failed to request I/O memory\n");
-		error = -EBUSY;
-		goto err_free_input;
-	}
-
-	kscandat->kscan_base = ioremap(kscandat->iores->start,
-				       resource_size(kscandat->iores));
-	if (!kscandat->kscan_base) {
-		dev_err(&pdev->dev, "failed to remap I/O memory\n");
-		error = -EBUSY;
-		goto err_release_memregion;
-	}
+	kscandat->kscan_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(kscandat->kscan_base))
+		return PTR_ERR(kscandat->kscan_base);
 
 	/* Get the key scanner clock */
-	kscandat->clk = clk_get(&pdev->dev, NULL);
+	kscandat->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(kscandat->clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
-		error = PTR_ERR(kscandat->clk);
-		goto err_unmap;
+		return PTR_ERR(kscandat->clk);
 	}
 
 	/* Configure the key scanner */
 	error = clk_prepare_enable(kscandat->clk);
 	if (error)
-		goto err_clk_put;
+		return error;
 
 	writel(kscandat->deb_clks, LPC32XX_KS_DEB(kscandat->kscan_base));
 	writel(kscandat->scan_delay, LPC32XX_KS_SCAN_CTL(kscandat->kscan_base));
@@ -277,52 +258,20 @@
 	writel(1, LPC32XX_KS_IRQ(kscandat->kscan_base));
 	clk_disable_unprepare(kscandat->clk);
 
-	error = request_irq(irq, lpc32xx_kscan_irq, 0, pdev->name, kscandat);
+	error = devm_request_irq(&pdev->dev, irq, lpc32xx_kscan_irq, 0,
+				 pdev->name, kscandat);
 	if (error) {
 		dev_err(&pdev->dev, "failed to request irq\n");
-		goto err_clk_put;
+		return error;
 	}
 
 	error = input_register_device(kscandat->input);
 	if (error) {
 		dev_err(&pdev->dev, "failed to register input device\n");
-		goto err_free_irq;
+		return error;
 	}
 
 	platform_set_drvdata(pdev, kscandat);
-	return 0;
-
-err_free_irq:
-	free_irq(irq, kscandat);
-err_clk_put:
-	clk_put(kscandat->clk);
-err_unmap:
-	iounmap(kscandat->kscan_base);
-err_release_memregion:
-	release_mem_region(kscandat->iores->start,
-			   resource_size(kscandat->iores));
-err_free_input:
-	input_free_device(kscandat->input);
-err_free_keymap:
-	kfree(kscandat->keymap);
-err_free_mem:
-	kfree(kscandat);
-
-	return error;
-}
-
-static int lpc32xx_kscan_remove(struct platform_device *pdev)
-{
-	struct lpc32xx_kscan_drv *kscandat = platform_get_drvdata(pdev);
-
-	free_irq(platform_get_irq(pdev, 0), kscandat);
-	clk_put(kscandat->clk);
-	iounmap(kscandat->kscan_base);
-	release_mem_region(kscandat->iores->start,
-			   resource_size(kscandat->iores));
-	input_unregister_device(kscandat->input);
-	kfree(kscandat->keymap);
-	kfree(kscandat);
 
 	return 0;
 }
@@ -378,7 +327,6 @@
 
 static struct platform_driver lpc32xx_kscan_driver = {
 	.probe		= lpc32xx_kscan_probe,
-	.remove		= lpc32xx_kscan_remove,
 	.driver		= {
 		.name	= DRV_NAME,
 		.pm	= &lpc32xx_kscan_pm_ops,
diff --git a/drivers/input/keyboard/mpr121_touchkey.c b/drivers/input/keyboard/mpr121_touchkey.c
index 009c822..3aa2ec4 100644
--- a/drivers/input/keyboard/mpr121_touchkey.c
+++ b/drivers/input/keyboard/mpr121_touchkey.c
@@ -214,13 +214,14 @@
 		return -EINVAL;
 	}
 
-	mpr121 = kzalloc(sizeof(struct mpr121_touchkey), GFP_KERNEL);
-	input_dev = input_allocate_device();
-	if (!mpr121 || !input_dev) {
-		dev_err(&client->dev, "Failed to allocate memory\n");
-		error = -ENOMEM;
-		goto err_free_mem;
-	}
+	mpr121 = devm_kzalloc(&client->dev, sizeof(*mpr121),
+			      GFP_KERNEL);
+	if (!mpr121)
+		return -ENOMEM;
+
+	input_dev = devm_input_allocate_device(&client->dev);
+	if (!input_dev)
+		return -ENOMEM;
 
 	mpr121->client = client;
 	mpr121->input_dev = input_dev;
@@ -243,44 +244,26 @@
 	error = mpr121_phys_init(pdata, mpr121, client);
 	if (error) {
 		dev_err(&client->dev, "Failed to init register\n");
-		goto err_free_mem;
+		return error;
 	}
 
-	error = request_threaded_irq(client->irq, NULL,
+	error = devm_request_threaded_irq(&client->dev, client->irq, NULL,
 				     mpr_touchkey_interrupt,
 				     IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 				     client->dev.driver->name, mpr121);
 	if (error) {
 		dev_err(&client->dev, "Failed to register interrupt\n");
-		goto err_free_mem;
+		return error;
 	}
 
 	error = input_register_device(input_dev);
 	if (error)
-		goto err_free_irq;
+		return error;
 
 	i2c_set_clientdata(client, mpr121);
 	device_init_wakeup(&client->dev, pdata->wakeup);
 
 	return 0;
-
-err_free_irq:
-	free_irq(client->irq, mpr121);
-err_free_mem:
-	input_free_device(input_dev);
-	kfree(mpr121);
-	return error;
-}
-
-static int mpr_touchkey_remove(struct i2c_client *client)
-{
-	struct mpr121_touchkey *mpr121 = i2c_get_clientdata(client);
-
-	free_irq(client->irq, mpr121);
-	input_unregister_device(mpr121->input_dev);
-	kfree(mpr121);
-
-	return 0;
 }
 
 #ifdef CONFIG_PM_SLEEP
@@ -327,7 +310,6 @@
 	},
 	.id_table	= mpr121_id,
 	.probe		= mpr_touchkey_probe,
-	.remove		= mpr_touchkey_remove,
 };
 
 module_i2c_driver(mpr_touchkey_driver);
diff --git a/drivers/input/keyboard/pxa27x_keypad.c b/drivers/input/keyboard/pxa27x_keypad.c
index 6ab3e7c..a90d6bdc 100644
--- a/drivers/input/keyboard/pxa27x_keypad.c
+++ b/drivers/input/keyboard/pxa27x_keypad.c
@@ -741,37 +741,27 @@
 		return -ENXIO;
 	}
 
-	keypad = kzalloc(sizeof(struct pxa27x_keypad), GFP_KERNEL);
-	input_dev = input_allocate_device();
-	if (!keypad || !input_dev) {
-		dev_err(&pdev->dev, "failed to allocate memory\n");
-		error = -ENOMEM;
-		goto failed_free;
-	}
+	keypad = devm_kzalloc(&pdev->dev, sizeof(*keypad),
+			      GFP_KERNEL);
+	if (!keypad)
+		return -ENOMEM;
+
+	input_dev = devm_input_allocate_device(&pdev->dev);
+	if (!input_dev)
+		return -ENOMEM;
 
 	keypad->pdata = pdata;
 	keypad->input_dev = input_dev;
 	keypad->irq = irq;
 
-	res = request_mem_region(res->start, resource_size(res), pdev->name);
-	if (res == NULL) {
-		dev_err(&pdev->dev, "failed to request I/O memory\n");
-		error = -EBUSY;
-		goto failed_free;
-	}
+	keypad->mmio_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(keypad->mmio_base))
+		return PTR_ERR(keypad->mmio_base);
 
-	keypad->mmio_base = ioremap(res->start, resource_size(res));
-	if (keypad->mmio_base == NULL) {
-		dev_err(&pdev->dev, "failed to remap I/O memory\n");
-		error = -ENXIO;
-		goto failed_free_mem;
-	}
-
-	keypad->clk = clk_get(&pdev->dev, NULL);
+	keypad->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(keypad->clk)) {
 		dev_err(&pdev->dev, "failed to get keypad clock\n");
-		error = PTR_ERR(keypad->clk);
-		goto failed_free_io;
+		return PTR_ERR(keypad->clk);
 	}
 
 	input_dev->name = pdev->name;
@@ -802,7 +792,7 @@
 	}
 	if (error) {
 		dev_err(&pdev->dev, "failed to build keycode\n");
-		goto failed_put_clk;
+		return error;
 	}
 
 	keypad->row_shift = get_count_order(pdata->matrix_key_cols);
@@ -812,61 +802,26 @@
 		input_dev->evbit[0] |= BIT_MASK(EV_REL);
 	}
 
-	error = request_irq(irq, pxa27x_keypad_irq_handler, 0,
-			    pdev->name, keypad);
+	error = devm_request_irq(&pdev->dev, irq, pxa27x_keypad_irq_handler,
+				 0, pdev->name, keypad);
 	if (error) {
 		dev_err(&pdev->dev, "failed to request IRQ\n");
-		goto failed_put_clk;
+		return error;
 	}
 
 	/* Register the input device */
 	error = input_register_device(input_dev);
 	if (error) {
 		dev_err(&pdev->dev, "failed to register input device\n");
-		goto failed_free_irq;
+		return error;
 	}
 
 	platform_set_drvdata(pdev, keypad);
 	device_init_wakeup(&pdev->dev, 1);
 
 	return 0;
-
-failed_free_irq:
-	free_irq(irq, keypad);
-failed_put_clk:
-	clk_put(keypad->clk);
-failed_free_io:
-	iounmap(keypad->mmio_base);
-failed_free_mem:
-	release_mem_region(res->start, resource_size(res));
-failed_free:
-	input_free_device(input_dev);
-	kfree(keypad);
-	return error;
 }
 
-static int pxa27x_keypad_remove(struct platform_device *pdev)
-{
-	struct pxa27x_keypad *keypad = platform_get_drvdata(pdev);
-	struct resource *res;
-
-	free_irq(keypad->irq, keypad);
-	clk_put(keypad->clk);
-
-	input_unregister_device(keypad->input_dev);
-	iounmap(keypad->mmio_base);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(res->start, resource_size(res));
-
-	kfree(keypad);
-
-	return 0;
-}
-
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:pxa27x-keypad");
-
 #ifdef CONFIG_OF
 static const struct of_device_id pxa27x_keypad_dt_match[] = {
 	{ .compatible = "marvell,pxa27x-keypad" },
@@ -877,7 +832,6 @@
 
 static struct platform_driver pxa27x_keypad_driver = {
 	.probe		= pxa27x_keypad_probe,
-	.remove		= pxa27x_keypad_remove,
 	.driver		= {
 		.name	= "pxa27x-keypad",
 		.of_match_table = of_match_ptr(pxa27x_keypad_dt_match),
@@ -888,3 +842,5 @@
 
 MODULE_DESCRIPTION("PXA27x Keypad Controller Driver");
 MODULE_LICENSE("GPL");
+/* work with hotplug and coldplug */
+MODULE_ALIAS("platform:pxa27x-keypad");
diff --git a/drivers/input/misc/88pm860x_onkey.c b/drivers/input/misc/88pm860x_onkey.c
index cfdca6e..cc87443 100644
--- a/drivers/input/misc/88pm860x_onkey.c
+++ b/drivers/input/misc/88pm860x_onkey.c
@@ -112,8 +112,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int pm860x_onkey_suspend(struct device *dev)
+static int __maybe_unused pm860x_onkey_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent);
@@ -122,7 +121,7 @@
 		chip->wakeup_flag |= 1 << PM8607_IRQ_ONKEY;
 	return 0;
 }
-static int pm860x_onkey_resume(struct device *dev)
+static int __maybe_unused pm860x_onkey_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent);
@@ -131,7 +130,6 @@
 		chip->wakeup_flag &= ~(1 << PM8607_IRQ_ONKEY);
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(pm860x_onkey_pm_ops, pm860x_onkey_suspend, pm860x_onkey_resume);
 
diff --git a/drivers/input/misc/ad714x-i2c.c b/drivers/input/misc/ad714x-i2c.c
index e0f5225..189bdc8 100644
--- a/drivers/input/misc/ad714x-i2c.c
+++ b/drivers/input/misc/ad714x-i2c.c
@@ -13,17 +13,15 @@
 #include <linux/pm.h>
 #include "ad714x.h"
 
-#ifdef CONFIG_PM_SLEEP
-static int ad714x_i2c_suspend(struct device *dev)
+static int __maybe_unused ad714x_i2c_suspend(struct device *dev)
 {
 	return ad714x_disable(i2c_get_clientdata(to_i2c_client(dev)));
 }
 
-static int ad714x_i2c_resume(struct device *dev)
+static int __maybe_unused ad714x_i2c_resume(struct device *dev)
 {
 	return ad714x_enable(i2c_get_clientdata(to_i2c_client(dev)));
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(ad714x_i2c_pm, ad714x_i2c_suspend, ad714x_i2c_resume);
 
diff --git a/drivers/input/misc/ad714x-spi.c b/drivers/input/misc/ad714x-spi.c
index 3a90b710..a79e50b 100644
--- a/drivers/input/misc/ad714x-spi.c
+++ b/drivers/input/misc/ad714x-spi.c
@@ -16,17 +16,15 @@
 #define AD714x_SPI_CMD_PREFIX      0xE000   /* bits 15:11 */
 #define AD714x_SPI_READ            BIT(10)
 
-#ifdef CONFIG_PM_SLEEP
-static int ad714x_spi_suspend(struct device *dev)
+static int __maybe_unused ad714x_spi_suspend(struct device *dev)
 {
 	return ad714x_disable(spi_get_drvdata(to_spi_device(dev)));
 }
 
-static int ad714x_spi_resume(struct device *dev)
+static int __maybe_unused ad714x_spi_resume(struct device *dev)
 {
 	return ad714x_enable(spi_get_drvdata(to_spi_device(dev)));
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(ad714x_spi_pm, ad714x_spi_suspend, ad714x_spi_resume);
 
diff --git a/drivers/input/misc/adxl34x-i2c.c b/drivers/input/misc/adxl34x-i2c.c
index 416f47d..470bfd6 100644
--- a/drivers/input/misc/adxl34x-i2c.c
+++ b/drivers/input/misc/adxl34x-i2c.c
@@ -105,8 +105,7 @@
 	return adxl34x_remove(ac);
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int adxl34x_i2c_suspend(struct device *dev)
+static int __maybe_unused adxl34x_i2c_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adxl34x *ac = i2c_get_clientdata(client);
@@ -116,7 +115,7 @@
 	return 0;
 }
 
-static int adxl34x_i2c_resume(struct device *dev)
+static int __maybe_unused adxl34x_i2c_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adxl34x *ac = i2c_get_clientdata(client);
@@ -125,7 +124,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(adxl34x_i2c_pm, adxl34x_i2c_suspend,
 			 adxl34x_i2c_resume);
diff --git a/drivers/input/misc/adxl34x-spi.c b/drivers/input/misc/adxl34x-spi.c
index 76dc067..da6e76b 100644
--- a/drivers/input/misc/adxl34x-spi.c
+++ b/drivers/input/misc/adxl34x-spi.c
@@ -94,8 +94,7 @@
 	return adxl34x_remove(ac);
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int adxl34x_spi_suspend(struct device *dev)
+static int __maybe_unused adxl34x_spi_suspend(struct device *dev)
 {
 	struct spi_device *spi = to_spi_device(dev);
 	struct adxl34x *ac = spi_get_drvdata(spi);
@@ -105,7 +104,7 @@
 	return 0;
 }
 
-static int adxl34x_spi_resume(struct device *dev)
+static int __maybe_unused adxl34x_spi_resume(struct device *dev)
 {
 	struct spi_device *spi = to_spi_device(dev);
 	struct adxl34x *ac = spi_get_drvdata(spi);
@@ -114,7 +113,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(adxl34x_spi_pm, adxl34x_spi_suspend,
 			 adxl34x_spi_resume);
diff --git a/drivers/input/misc/drv260x.c b/drivers/input/misc/drv260x.c
index cab87f5..a364e10 100644
--- a/drivers/input/misc/drv260x.c
+++ b/drivers/input/misc/drv260x.c
@@ -639,8 +639,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int drv260x_suspend(struct device *dev)
+static int __maybe_unused drv260x_suspend(struct device *dev)
 {
 	struct drv260x_data *haptics = dev_get_drvdata(dev);
 	int ret = 0;
@@ -672,7 +671,7 @@
 	return ret;
 }
 
-static int drv260x_resume(struct device *dev)
+static int __maybe_unused drv260x_resume(struct device *dev)
 {
 	struct drv260x_data *haptics = dev_get_drvdata(dev);
 	int ret = 0;
@@ -702,7 +701,6 @@
 	mutex_unlock(&haptics->input_dev->mutex);
 	return ret;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(drv260x_pm_ops, drv260x_suspend, drv260x_resume);
 
diff --git a/drivers/input/misc/drv2667.c b/drivers/input/misc/drv2667.c
index 0f43758..a021744 100644
--- a/drivers/input/misc/drv2667.c
+++ b/drivers/input/misc/drv2667.c
@@ -406,8 +406,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int drv2667_suspend(struct device *dev)
+static int __maybe_unused drv2667_suspend(struct device *dev)
 {
 	struct drv2667_data *haptics = dev_get_drvdata(dev);
 	int ret = 0;
@@ -436,7 +435,7 @@
 	return ret;
 }
 
-static int drv2667_resume(struct device *dev)
+static int __maybe_unused drv2667_resume(struct device *dev)
 {
 	struct drv2667_data *haptics = dev_get_drvdata(dev);
 	int ret = 0;
@@ -464,7 +463,6 @@
 	mutex_unlock(&haptics->input_dev->mutex);
 	return ret;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(drv2667_pm_ops, drv2667_suspend, drv2667_resume);
 
diff --git a/drivers/input/misc/gp2ap002a00f.c b/drivers/input/misc/gp2ap002a00f.c
index de21e31..0ac176d 100644
--- a/drivers/input/misc/gp2ap002a00f.c
+++ b/drivers/input/misc/gp2ap002a00f.c
@@ -225,8 +225,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int gp2a_suspend(struct device *dev)
+static int __maybe_unused gp2a_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct gp2a_data *dt = i2c_get_clientdata(client);
@@ -244,7 +243,7 @@
 	return retval;
 }
 
-static int gp2a_resume(struct device *dev)
+static int __maybe_unused gp2a_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct gp2a_data *dt = i2c_get_clientdata(client);
@@ -261,7 +260,6 @@
 
 	return retval;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(gp2a_pm, gp2a_suspend, gp2a_resume);
 
diff --git a/drivers/input/misc/ims-pcu.c b/drivers/input/misc/ims-pcu.c
index afed8e2..ac1fa5f 100644
--- a/drivers/input/misc/ims-pcu.c
+++ b/drivers/input/misc/ims-pcu.c
@@ -1851,7 +1851,7 @@
 
 static int ims_pcu_init_application_mode(struct ims_pcu *pcu)
 {
-	static atomic_t device_no = ATOMIC_INIT(0);
+	static atomic_t device_no = ATOMIC_INIT(-1);
 
 	const struct ims_pcu_device_info *info;
 	int error;
@@ -1882,7 +1882,7 @@
 	}
 
 	/* Device appears to be operable, complete initialization */
-	pcu->device_no = atomic_inc_return(&device_no) - 1;
+	pcu->device_no = atomic_inc_return(&device_no);
 
 	/*
 	 * PCU-B devices, both GEN_1 and GEN_2 do not have OFN sensor
diff --git a/drivers/input/misc/kxtj9.c b/drivers/input/misc/kxtj9.c
index d708478..6e29349 100644
--- a/drivers/input/misc/kxtj9.c
+++ b/drivers/input/misc/kxtj9.c
@@ -615,8 +615,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int kxtj9_suspend(struct device *dev)
+static int __maybe_unused kxtj9_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct kxtj9_data *tj9 = i2c_get_clientdata(client);
@@ -631,7 +630,7 @@
 	return 0;
 }
 
-static int kxtj9_resume(struct device *dev)
+static int __maybe_unused kxtj9_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct kxtj9_data *tj9 = i2c_get_clientdata(client);
@@ -646,7 +645,6 @@
 	mutex_unlock(&input_dev->mutex);
 	return retval;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(kxtj9_pm_ops, kxtj9_suspend, kxtj9_resume);
 
diff --git a/drivers/input/misc/max77693-haptic.c b/drivers/input/misc/max77693-haptic.c
index 034093e..39e930c 100644
--- a/drivers/input/misc/max77693-haptic.c
+++ b/drivers/input/misc/max77693-haptic.c
@@ -309,8 +309,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int max77693_haptic_suspend(struct device *dev)
+static int __maybe_unused max77693_haptic_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct max77693_haptic *haptic = platform_get_drvdata(pdev);
@@ -323,7 +322,7 @@
 	return 0;
 }
 
-static int max77693_haptic_resume(struct device *dev)
+static int __maybe_unused max77693_haptic_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct max77693_haptic *haptic = platform_get_drvdata(pdev);
@@ -335,7 +334,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(max77693_haptic_pm_ops,
 			 max77693_haptic_suspend, max77693_haptic_resume);
diff --git a/drivers/input/misc/max8925_onkey.c b/drivers/input/misc/max8925_onkey.c
index 297e2a9..7c49b8d 100644
--- a/drivers/input/misc/max8925_onkey.c
+++ b/drivers/input/misc/max8925_onkey.c
@@ -133,8 +133,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int max8925_onkey_suspend(struct device *dev)
+static int __maybe_unused max8925_onkey_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct max8925_onkey_info *info = platform_get_drvdata(pdev);
@@ -148,7 +147,7 @@
 	return 0;
 }
 
-static int max8925_onkey_resume(struct device *dev)
+static int __maybe_unused max8925_onkey_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct max8925_onkey_info *info = platform_get_drvdata(pdev);
@@ -161,7 +160,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(max8925_onkey_pm_ops, max8925_onkey_suspend, max8925_onkey_resume);
 
diff --git a/drivers/input/misc/max8997_haptic.c b/drivers/input/misc/max8997_haptic.c
index 5b3154e..d0f6872 100644
--- a/drivers/input/misc/max8997_haptic.c
+++ b/drivers/input/misc/max8997_haptic.c
@@ -378,8 +378,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int max8997_haptic_suspend(struct device *dev)
+static int __maybe_unused max8997_haptic_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct max8997_haptic *chip = platform_get_drvdata(pdev);
@@ -388,7 +387,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(max8997_haptic_pm_ops, max8997_haptic_suspend, NULL);
 
diff --git a/drivers/input/misc/palmas-pwrbutton.c b/drivers/input/misc/palmas-pwrbutton.c
index 066c5ab..1f9b5ee 100644
--- a/drivers/input/misc/palmas-pwrbutton.c
+++ b/drivers/input/misc/palmas-pwrbutton.c
@@ -260,7 +260,6 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
 /**
  * palmas_pwron_suspend() - suspend handler
  * @dev:	power button device
@@ -269,7 +268,7 @@
  *
  * Return: 0
  */
-static int palmas_pwron_suspend(struct device *dev)
+static int __maybe_unused palmas_pwron_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct palmas_pwron *pwron = platform_get_drvdata(pdev);
@@ -290,7 +289,7 @@
  *
  * Return: 0
  */
-static int palmas_pwron_resume(struct device *dev)
+static int __maybe_unused palmas_pwron_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct palmas_pwron *pwron = platform_get_drvdata(pdev);
@@ -300,7 +299,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(palmas_pwron_pm,
 			 palmas_pwron_suspend, palmas_pwron_resume);
diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
index e9c77a9..5113877 100644
--- a/drivers/input/misc/pm8xxx-vibrator.c
+++ b/drivers/input/misc/pm8xxx-vibrator.c
@@ -199,8 +199,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int pm8xxx_vib_suspend(struct device *dev)
+static int __maybe_unused pm8xxx_vib_suspend(struct device *dev)
 {
 	struct pm8xxx_vib *vib = dev_get_drvdata(dev);
 
@@ -209,7 +208,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(pm8xxx_vib_pm_ops, pm8xxx_vib_suspend, NULL);
 
diff --git a/drivers/input/misc/pmic8xxx-pwrkey.c b/drivers/input/misc/pmic8xxx-pwrkey.c
index cb79917..c4ca20e 100644
--- a/drivers/input/misc/pmic8xxx-pwrkey.c
+++ b/drivers/input/misc/pmic8xxx-pwrkey.c
@@ -53,8 +53,7 @@
 	return IRQ_HANDLED;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int pmic8xxx_pwrkey_suspend(struct device *dev)
+static int __maybe_unused pmic8xxx_pwrkey_suspend(struct device *dev)
 {
 	struct pmic8xxx_pwrkey *pwrkey = dev_get_drvdata(dev);
 
@@ -64,7 +63,7 @@
 	return 0;
 }
 
-static int pmic8xxx_pwrkey_resume(struct device *dev)
+static int __maybe_unused pmic8xxx_pwrkey_resume(struct device *dev)
 {
 	struct pmic8xxx_pwrkey *pwrkey = dev_get_drvdata(dev);
 
@@ -73,7 +72,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(pm8xxx_pwr_key_pm_ops,
 		pmic8xxx_pwrkey_suspend, pmic8xxx_pwrkey_resume);
diff --git a/drivers/input/misc/pwm-beeper.c b/drivers/input/misc/pwm-beeper.c
index 294aa48..a28ee70 100644
--- a/drivers/input/misc/pwm-beeper.c
+++ b/drivers/input/misc/pwm-beeper.c
@@ -144,8 +144,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int pwm_beeper_suspend(struct device *dev)
+static int __maybe_unused pwm_beeper_suspend(struct device *dev)
 {
 	struct pwm_beeper *beeper = dev_get_drvdata(dev);
 
@@ -155,7 +154,7 @@
 	return 0;
 }
 
-static int pwm_beeper_resume(struct device *dev)
+static int __maybe_unused pwm_beeper_resume(struct device *dev)
 {
 	struct pwm_beeper *beeper = dev_get_drvdata(dev);
 
@@ -170,6 +169,7 @@
 static SIMPLE_DEV_PM_OPS(pwm_beeper_pm_ops,
 			 pwm_beeper_suspend, pwm_beeper_resume);
 
+#ifdef CONFIG_PM_SLEEP
 #define PWM_BEEPER_PM_OPS (&pwm_beeper_pm_ops)
 #else
 #define PWM_BEEPER_PM_OPS NULL
diff --git a/drivers/input/misc/sirfsoc-onkey.c b/drivers/input/misc/sirfsoc-onkey.c
index 4faf9f8d..9d5b89b 100644
--- a/drivers/input/misc/sirfsoc-onkey.c
+++ b/drivers/input/misc/sirfsoc-onkey.c
@@ -179,8 +179,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int sirfsoc_pwrc_resume(struct device *dev)
+static int __maybe_unused sirfsoc_pwrc_resume(struct device *dev)
 {
 	struct sirfsoc_pwrc_drvdata *pwrcdrv = dev_get_drvdata(dev);
 	struct input_dev *input = pwrcdrv->input;
@@ -196,7 +195,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(sirfsoc_pwrc_pm_ops, NULL, sirfsoc_pwrc_resume);
 
diff --git a/drivers/input/misc/twl4030-vibra.c b/drivers/input/misc/twl4030-vibra.c
index ccd6dd1..fc17b95 100644
--- a/drivers/input/misc/twl4030-vibra.c
+++ b/drivers/input/misc/twl4030-vibra.c
@@ -157,8 +157,7 @@
 }
 
 /*** Module ***/
-#ifdef CONFIG_PM_SLEEP
-static int twl4030_vibra_suspend(struct device *dev)
+static int __maybe_unused twl4030_vibra_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct vibra_info *info = platform_get_drvdata(pdev);
@@ -169,12 +168,11 @@
 	return 0;
 }
 
-static int twl4030_vibra_resume(struct device *dev)
+static int __maybe_unused twl4030_vibra_resume(struct device *dev)
 {
 	vibra_disable_leds();
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(twl4030_vibra_pm_ops,
 			 twl4030_vibra_suspend, twl4030_vibra_resume);
diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c
index 96e0e0c..0e0d094 100644
--- a/drivers/input/misc/twl6040-vibra.c
+++ b/drivers/input/misc/twl6040-vibra.c
@@ -236,8 +236,7 @@
 	mutex_unlock(&info->mutex);
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int twl6040_vibra_suspend(struct device *dev)
+static int __maybe_unused twl6040_vibra_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct vibra_info *info = platform_get_drvdata(pdev);
@@ -251,7 +250,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(twl6040_vibra_pm_ops, twl6040_vibra_suspend, NULL);
 
diff --git a/drivers/input/mouse/Kconfig b/drivers/input/mouse/Kconfig
index 366fc7a..d8b46b0 100644
--- a/drivers/input/mouse/Kconfig
+++ b/drivers/input/mouse/Kconfig
@@ -215,6 +215,36 @@
 	  To compile this driver as a module, choose M here: the module will be
 	  called cyapa.
 
+config MOUSE_ELAN_I2C
+	tristate "ELAN I2C Touchpad support"
+	depends on I2C
+	help
+	  This driver adds support for Elan I2C/SMbus Trackpads.
+
+	  Say Y here if you have a ELAN I2C/SMbus Touchpad.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called elan_i2c.
+
+config MOUSE_ELAN_I2C_I2C
+	bool "Enable I2C support"
+	depends on MOUSE_ELAN_I2C
+	default y
+	help
+	   Say Y here if Elan Touchpad in your system is connected to
+	   a standard I2C controller.
+
+	   If unsure, say Y.
+
+config MOUSE_ELAN_I2C_SMBUS
+	bool "Enable SMbus support"
+	depends on MOUSE_ELAN_I2C
+	help
+	   Say Y here if Elan Touchpad in your system is connected to
+	   a SMbus adapter.
+
+	   If unsure, say Y.
+
 config MOUSE_INPORT
 	tristate "InPort/MS/ATIXL busmouse"
 	depends on ISA
diff --git a/drivers/input/mouse/Makefile b/drivers/input/mouse/Makefile
index dda507f..560003d 100644
--- a/drivers/input/mouse/Makefile
+++ b/drivers/input/mouse/Makefile
@@ -9,6 +9,7 @@
 obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)		+= cyapa.o
+obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)		+= logibm.o
@@ -34,3 +35,7 @@
 psmouse-$(CONFIG_MOUSE_PS2_TRACKPOINT)	+= trackpoint.o
 psmouse-$(CONFIG_MOUSE_PS2_TOUCHKIT)	+= touchkit_ps2.o
 psmouse-$(CONFIG_MOUSE_PS2_CYPRESS)	+= cypress_ps2.o
+
+elan_i2c-objs := elan_i2c_core.o
+elan_i2c-$(CONFIG_MOUSE_ELAN_I2C_I2C)	+= elan_i2c_i2c.o
+elan_i2c-$(CONFIG_MOUSE_ELAN_I2C_SMBUS)	+= elan_i2c_smbus.o
diff --git a/drivers/input/mouse/cyapa.c b/drivers/input/mouse/cyapa.c
index b409c3d..1bece8c 100644
--- a/drivers/input/mouse/cyapa.c
+++ b/drivers/input/mouse/cyapa.c
@@ -6,7 +6,7 @@
  *   Daniel Kurtz <djkurtz@chromium.org>
  *   Benson Leung <bleung@chromium.org>
  *
- * Copyright (C) 2011-2012 Cypress Semiconductor, Inc.
+ * Copyright (C) 2011-2014 Cypress Semiconductor, Inc.
  * Copyright (C) 2011-2012 Google, Inc.
  *
  * This file is subject to the terms and conditions of the GNU General Public
@@ -206,7 +206,6 @@
 	struct i2c_client *client;
 	struct input_dev *input;
 	char phys[32];	/* device physical location */
-	int irq;
 	bool irq_wake;  /* irq wake is enabled */
 	bool smbus;
 
@@ -422,8 +421,8 @@
  */
 static int cyapa_get_state(struct cyapa *cyapa)
 {
-	int ret;
 	u8 status[BL_STATUS_SIZE];
+	int error;
 
 	cyapa->state = CYAPA_STATE_NO_DEVICE;
 
@@ -433,18 +432,18 @@
 	 * If the device is in operation mode, this will be the DATA regs.
 	 *
 	 */
-	ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, BL_STATUS_SIZE,
-				       status);
+	error = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, BL_STATUS_SIZE,
+				         status);
 
 	/*
 	 * On smbus systems in OP mode, the i2c_reg_read will fail with
 	 * -ETIMEDOUT.  In this case, try again using the smbus equivalent
 	 * command.  This should return a BL_HEAD indicating CYAPA_STATE_OP.
 	 */
-	if (cyapa->smbus && (ret == -ETIMEDOUT || ret == -ENXIO))
-		ret = cyapa_read_block(cyapa, CYAPA_CMD_BL_STATUS, status);
+	if (cyapa->smbus && (error == -ETIMEDOUT || error == -ENXIO))
+		error = cyapa_read_block(cyapa, CYAPA_CMD_BL_STATUS, status);
 
-	if (ret != BL_STATUS_SIZE)
+	if (error != BL_STATUS_SIZE)
 		goto error;
 
 	if ((status[REG_OP_STATUS] & OP_STATUS_SRC) == OP_STATUS_SRC) {
@@ -454,7 +453,7 @@
 			cyapa->state = CYAPA_STATE_OP;
 			break;
 		default:
-			ret = -EAGAIN;
+			error = -EAGAIN;
 			goto error;
 		}
 	} else {
@@ -468,7 +467,7 @@
 
 	return 0;
 error:
-	return (ret < 0) ? ret : -EAGAIN;
+	return (error < 0) ? error : -EAGAIN;
 }
 
 /*
@@ -487,31 +486,31 @@
  */
 static int cyapa_poll_state(struct cyapa *cyapa, unsigned int timeout)
 {
-	int ret;
+	int error;
 	int tries = timeout / 100;
 
-	ret = cyapa_get_state(cyapa);
-	while ((ret || cyapa->state >= CYAPA_STATE_BL_BUSY) && tries--) {
+	error = cyapa_get_state(cyapa);
+	while ((error || cyapa->state >= CYAPA_STATE_BL_BUSY) && tries--) {
 		msleep(100);
-		ret = cyapa_get_state(cyapa);
+		error = cyapa_get_state(cyapa);
 	}
-	return (ret == -EAGAIN || ret == -ETIMEDOUT) ? -ETIMEDOUT : ret;
+	return (error == -EAGAIN || error == -ETIMEDOUT) ? -ETIMEDOUT : error;
 }
 
 static int cyapa_bl_deactivate(struct cyapa *cyapa)
 {
-	int ret;
+	int error;
 
-	ret = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
-					bl_deactivate);
-	if (ret < 0)
-		return ret;
+	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
+					  bl_deactivate);
+	if (error)
+		return error;
 
 	/* wait for bootloader to switch to idle state; should take < 100ms */
 	msleep(100);
-	ret = cyapa_poll_state(cyapa, 500);
-	if (ret < 0)
-		return ret;
+	error = cyapa_poll_state(cyapa, 500);
+	if (error)
+		return error;
 	if (cyapa->state != CYAPA_STATE_BL_IDLE)
 		return -EAGAIN;
 	return 0;
@@ -532,11 +531,11 @@
  */
 static int cyapa_bl_exit(struct cyapa *cyapa)
 {
-	int ret;
+	int error;
 
-	ret = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
-	if (ret < 0)
-		return ret;
+	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
+	if (error)
+		return error;
 
 	/*
 	 * Wait for bootloader to exit, and operation mode to start.
@@ -548,9 +547,9 @@
 	 * updated to new firmware, it must first calibrate its sensors, which
 	 * can take up to an additional 2 seconds.
 	 */
-	ret = cyapa_poll_state(cyapa, 2000);
-	if (ret < 0)
-		return ret;
+	error = cyapa_poll_state(cyapa, 2000);
+	if (error < 0)
+		return error;
 	if (cyapa->state != CYAPA_STATE_OP)
 		return -EAGAIN;
 
@@ -577,10 +576,13 @@
 	power = ret & ~PWR_MODE_MASK;
 	power |= power_mode & PWR_MODE_MASK;
 	ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
-	if (ret < 0)
+	if (ret < 0) {
 		dev_err(dev, "failed to set power_mode 0x%02x err = %d\n",
 			power_mode, ret);
-	return ret;
+		return ret;
+	}
+
+	return 0;
 }
 
 static int cyapa_get_query_data(struct cyapa *cyapa)
@@ -637,28 +639,28 @@
 {
 	struct device *dev = &cyapa->client->dev;
 	static const char unique_str[] = "CYTRA";
-	int ret;
+	int error;
 
-	ret = cyapa_poll_state(cyapa, 2000);
-	if (ret < 0)
-		return ret;
+	error = cyapa_poll_state(cyapa, 2000);
+	if (error)
+		return error;
 	switch (cyapa->state) {
 	case CYAPA_STATE_BL_ACTIVE:
-		ret = cyapa_bl_deactivate(cyapa);
-		if (ret)
-			return ret;
+		error = cyapa_bl_deactivate(cyapa);
+		if (error)
+			return error;
 
 	/* Fallthrough state */
 	case CYAPA_STATE_BL_IDLE:
-		ret = cyapa_bl_exit(cyapa);
-		if (ret)
-			return ret;
+		error = cyapa_bl_exit(cyapa);
+		if (error)
+			return error;
 
 	/* Fallthrough state */
 	case CYAPA_STATE_OP:
-		ret = cyapa_get_query_data(cyapa);
-		if (ret < 0)
-			return ret;
+		error = cyapa_get_query_data(cyapa);
+		if (error)
+			return error;
 
 		/* only support firmware protocol gen3 */
 		if (cyapa->gen != CYAPA_GEN3) {
@@ -753,18 +755,42 @@
 	return ret;
 }
 
+static int cyapa_open(struct input_dev *input)
+{
+	struct cyapa *cyapa = input_get_drvdata(input);
+	struct i2c_client *client = cyapa->client;
+	int error;
+
+	error = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
+	if (error) {
+		dev_err(&client->dev, "set active power failed: %d\n", error);
+		return error;
+	}
+
+	enable_irq(client->irq);
+	return 0;
+}
+
+static void cyapa_close(struct input_dev *input)
+{
+	struct cyapa *cyapa = input_get_drvdata(input);
+
+	disable_irq(cyapa->client->irq);
+	cyapa_set_power_mode(cyapa, PWR_MODE_OFF);
+}
+
 static int cyapa_create_input_dev(struct cyapa *cyapa)
 {
 	struct device *dev = &cyapa->client->dev;
-	int ret;
 	struct input_dev *input;
+	int error;
 
 	if (!cyapa->physical_size_x || !cyapa->physical_size_y)
 		return -EINVAL;
 
-	input = cyapa->input = input_allocate_device();
+	input = devm_input_allocate_device(dev);
 	if (!input) {
-		dev_err(dev, "allocate memory for input device failed\n");
+		dev_err(dev, "failed to allocate memory for input device.\n");
 		return -ENOMEM;
 	}
 
@@ -772,14 +798,17 @@
 	input->phys = cyapa->phys;
 	input->id.bustype = BUS_I2C;
 	input->id.version = 1;
-	input->id.product = 0;  /* means any product in eventcomm. */
+	input->id.product = 0;  /* Means any product in eventcomm. */
 	input->dev.parent = &cyapa->client->dev;
 
+	input->open = cyapa_open;
+	input->close = cyapa_close;
+
 	input_set_drvdata(input, cyapa);
 
 	__set_bit(EV_ABS, input->evbit);
 
-	/* finger position */
+	/* Finger position */
 	input_set_abs_params(input, ABS_MT_POSITION_X, 0, cyapa->max_abs_x, 0,
 			     0);
 	input_set_abs_params(input, ABS_MT_POSITION_Y, 0, cyapa->max_abs_y, 0,
@@ -801,35 +830,25 @@
 	if (cyapa->btn_capability == CAPABILITY_LEFT_BTN_MASK)
 		__set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
 
-	/* handle pointer emulation and unused slots in core */
-	ret = input_mt_init_slots(input, CYAPA_MAX_MT_SLOTS,
-				  INPUT_MT_POINTER | INPUT_MT_DROP_UNUSED);
-	if (ret) {
-		dev_err(dev, "allocate memory for MT slots failed, %d\n", ret);
-		goto err_free_device;
+	/* Handle pointer emulation and unused slots in core */
+	error = input_mt_init_slots(input, CYAPA_MAX_MT_SLOTS,
+				    INPUT_MT_POINTER | INPUT_MT_DROP_UNUSED);
+	if (error) {
+		dev_err(dev, "failed to initialize MT slots: %d\n", error);
+		return error;
 	}
 
-	/* Register the device in input subsystem */
-	ret = input_register_device(input);
-	if (ret) {
-		dev_err(dev, "input device register failed, %d\n", ret);
-		goto err_free_device;
-	}
+	cyapa->input = input;
 	return 0;
-
-err_free_device:
-	input_free_device(input);
-	cyapa->input = NULL;
-	return ret;
 }
 
 static int cyapa_probe(struct i2c_client *client,
 		       const struct i2c_device_id *dev_id)
 {
-	int ret;
-	u8 adapter_func;
-	struct cyapa *cyapa;
 	struct device *dev = &client->dev;
+	struct cyapa *cyapa;
+	u8 adapter_func;
+	int error;
 
 	adapter_func = cyapa_check_adapter_functionality(client);
 	if (adapter_func == CYAPA_ADAPTER_FUNC_NONE) {
@@ -837,11 +856,9 @@
 		return -EIO;
 	}
 
-	cyapa = kzalloc(sizeof(struct cyapa), GFP_KERNEL);
-	if (!cyapa) {
-		dev_err(dev, "allocate memory for cyapa failed\n");
+	cyapa = devm_kzalloc(dev, sizeof(struct cyapa), GFP_KERNEL);
+	if (!cyapa)
 		return -ENOMEM;
-	}
 
 	cyapa->gen = CYAPA_GEN3;
 	cyapa->client = client;
@@ -852,67 +869,61 @@
 	/* i2c isn't supported, use smbus */
 	if (adapter_func == CYAPA_ADAPTER_FUNC_SMBUS)
 		cyapa->smbus = true;
+
 	cyapa->state = CYAPA_STATE_NO_DEVICE;
-	ret = cyapa_check_is_operational(cyapa);
-	if (ret) {
-		dev_err(dev, "device not operational, %d\n", ret);
-		goto err_mem_free;
+
+	error = cyapa_check_is_operational(cyapa);
+	if (error) {
+		dev_err(dev, "device not operational, %d\n", error);
+		return error;
 	}
 
-	ret = cyapa_create_input_dev(cyapa);
-	if (ret) {
-		dev_err(dev, "create input_dev instance failed, %d\n", ret);
-		goto err_mem_free;
+	/* Power down the device until we need it */
+	error = cyapa_set_power_mode(cyapa, PWR_MODE_OFF);
+	if (error) {
+		dev_err(dev, "failed to quiesce the device: %d\n", error);
+		return error;
 	}
 
-	ret = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
-	if (ret) {
-		dev_err(dev, "set active power failed, %d\n", ret);
-		goto err_unregister_device;
+	error = cyapa_create_input_dev(cyapa);
+	if (error)
+		return error;
+
+	error = devm_request_threaded_irq(dev, client->irq,
+					  NULL, cyapa_irq,
+					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+					  "cyapa", cyapa);
+	if (error) {
+		dev_err(dev, "failed to request threaded irq: %d\n", error);
+		return error;
 	}
 
-	cyapa->irq = client->irq;
-	ret = request_threaded_irq(cyapa->irq,
-				   NULL,
-				   cyapa_irq,
-				   IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
-				   "cyapa",
-				   cyapa);
-	if (ret) {
-		dev_err(dev, "IRQ request failed: %d\n, ", ret);
-		goto err_unregister_device;
+	/* Disable IRQ until the device is opened */
+	disable_irq(client->irq);
+
+	/* Register the device in input subsystem */
+	error = input_register_device(cyapa->input);
+	if (error) {
+		dev_err(dev, "failed to register input device: %d\n", error);
+		return error;
 	}
 
 	return 0;
-
-err_unregister_device:
-	input_unregister_device(cyapa->input);
-err_mem_free:
-	kfree(cyapa);
-
-	return ret;
 }
 
-static int cyapa_remove(struct i2c_client *client)
+static int __maybe_unused cyapa_suspend(struct device *dev)
 {
+	struct i2c_client *client = to_i2c_client(dev);
 	struct cyapa *cyapa = i2c_get_clientdata(client);
-
-	free_irq(cyapa->irq, cyapa);
-	input_unregister_device(cyapa->input);
-	cyapa_set_power_mode(cyapa, PWR_MODE_OFF);
-	kfree(cyapa);
-
-	return 0;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int cyapa_suspend(struct device *dev)
-{
-	int ret;
+	struct input_dev *input = cyapa->input;
 	u8 power_mode;
-	struct cyapa *cyapa = dev_get_drvdata(dev);
+	int error;
 
-	disable_irq(cyapa->irq);
+	error = mutex_lock_interruptible(&input->mutex);
+	if (error)
+		return error;
+
+	disable_irq(client->irq);
 
 	/*
 	 * Set trackpad device to idle mode if wakeup is allowed,
@@ -920,31 +931,44 @@
 	 */
 	power_mode = device_may_wakeup(dev) ? PWR_MODE_IDLE
 					    : PWR_MODE_OFF;
-	ret = cyapa_set_power_mode(cyapa, power_mode);
-	if (ret < 0)
-		dev_err(dev, "set power mode failed, %d\n", ret);
+	error = cyapa_set_power_mode(cyapa, power_mode);
+	if (error)
+		dev_err(dev, "resume: set power mode to %d failed: %d\n",
+			 power_mode, error);
 
 	if (device_may_wakeup(dev))
-		cyapa->irq_wake = (enable_irq_wake(cyapa->irq) == 0);
+		cyapa->irq_wake = (enable_irq_wake(client->irq) == 0);
+
+	mutex_unlock(&input->mutex);
+
 	return 0;
 }
 
-static int cyapa_resume(struct device *dev)
+static int __maybe_unused cyapa_resume(struct device *dev)
 {
-	int ret;
-	struct cyapa *cyapa = dev_get_drvdata(dev);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct cyapa *cyapa = i2c_get_clientdata(client);
+	struct input_dev *input = cyapa->input;
+	u8 power_mode;
+	int error;
+
+	mutex_lock(&input->mutex);
 
 	if (device_may_wakeup(dev) && cyapa->irq_wake)
-		disable_irq_wake(cyapa->irq);
+		disable_irq_wake(client->irq);
 
-	ret = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
-	if (ret)
-		dev_warn(dev, "resume active power failed, %d\n", ret);
+	power_mode = input->users ? PWR_MODE_FULL_ACTIVE : PWR_MODE_OFF;
+	error = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
+	if (error)
+		dev_warn(dev, "resume: set power mode to %d failed: %d\n",
+			 power_mode, error);
 
-	enable_irq(cyapa->irq);
+	enable_irq(client->irq);
+
+	mutex_unlock(&input->mutex);
+
 	return 0;
 }
-#endif /* CONFIG_PM_SLEEP */
 
 static SIMPLE_DEV_PM_OPS(cyapa_pm_ops, cyapa_suspend, cyapa_resume);
 
@@ -962,7 +986,6 @@
 	},
 
 	.probe = cyapa_probe,
-	.remove = cyapa_remove,
 	.id_table = cyapa_id_table,
 };
 
diff --git a/drivers/input/mouse/elan_i2c.h b/drivers/input/mouse/elan_i2c.h
new file mode 100644
index 0000000..2e83862
--- /dev/null
+++ b/drivers/input/mouse/elan_i2c.h
@@ -0,0 +1,86 @@
+/*
+ * Elan I2C/SMBus Touchpad driver
+ *
+ * Copyright (c) 2013 ELAN Microelectronics Corp.
+ *
+ * Author: 林政維 (Duson Lin) <dusonlin@emc.com.tw>
+ * Version: 1.5.5
+ *
+ * Based on cyapa driver:
+ * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
+ * copyright (c) 2011-2012 Google, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Trademarks are the property of their respective owners.
+ */
+
+#ifndef _ELAN_I2C_H
+#define _ELAN_i2C_H
+
+#include <linux/types.h>
+
+#define ETP_ENABLE_ABS		0x0001
+#define ETP_ENABLE_CALIBRATE	0x0002
+#define ETP_DISABLE_CALIBRATE	0x0000
+#define ETP_DISABLE_POWER	0x0001
+
+/* IAP Firmware handling */
+#define ETP_FW_NAME		"elan_i2c.bin"
+#define ETP_IAP_START_ADDR	0x0083
+#define ETP_FW_IAP_PAGE_ERR	(1 << 5)
+#define ETP_FW_IAP_INTF_ERR	(1 << 4)
+#define ETP_FW_PAGE_SIZE	64
+#define ETP_FW_PAGE_COUNT	768
+#define ETP_FW_SIZE		(ETP_FW_PAGE_SIZE * ETP_FW_PAGE_COUNT)
+
+struct i2c_client;
+struct completion;
+
+enum tp_mode {
+	IAP_MODE = 1,
+	MAIN_MODE
+};
+
+struct elan_transport_ops {
+	int (*initialize)(struct i2c_client *client);
+	int (*sleep_control)(struct i2c_client *, bool sleep);
+	int (*power_control)(struct i2c_client *, bool enable);
+	int (*set_mode)(struct i2c_client *client, u8 mode);
+
+	int (*calibrate)(struct i2c_client *client);
+	int (*calibrate_result)(struct i2c_client *client, u8 *val);
+
+	int (*get_baseline_data)(struct i2c_client *client,
+				 bool max_baseliune, u8 *value);
+
+	int (*get_version)(struct i2c_client *client, bool iap, u8 *version);
+	int (*get_sm_version)(struct i2c_client *client, u8 *version);
+	int (*get_checksum)(struct i2c_client *client, bool iap, u16 *csum);
+	int (*get_product_id)(struct i2c_client *client, u8 *id);
+
+	int (*get_max)(struct i2c_client *client,
+		       unsigned int *max_x, unsigned int *max_y);
+	int (*get_resolution)(struct i2c_client *client,
+			      u8 *hw_res_x, u8 *hw_res_y);
+	int (*get_num_traces)(struct i2c_client *client,
+			      unsigned int *x_tracenum,
+			      unsigned int *y_tracenum);
+
+	int (*iap_get_mode)(struct i2c_client *client, enum tp_mode *mode);
+	int (*iap_reset)(struct i2c_client *client);
+
+	int (*prepare_fw_update)(struct i2c_client *client);
+	int (*write_fw_block)(struct i2c_client *client,
+			      const u8 *page, u16 checksum, int idx);
+	int (*finish_fw_update)(struct i2c_client *client,
+				struct completion *reset_done);
+
+	int (*get_report)(struct i2c_client *client, u8 *report);
+};
+
+extern const struct elan_transport_ops elan_smbus_ops, elan_i2c_ops;
+
+#endif /* _ELAN_I2C_H */
diff --git a/drivers/input/mouse/elan_i2c_core.c b/drivers/input/mouse/elan_i2c_core.c
new file mode 100644
index 0000000..0cb2be4
--- /dev/null
+++ b/drivers/input/mouse/elan_i2c_core.c
@@ -0,0 +1,1137 @@
+/*
+ * Elan I2C/SMBus Touchpad driver
+ *
+ * Copyright (c) 2013 ELAN Microelectronics Corp.
+ *
+ * Author: 林政維 (Duson Lin) <dusonlin@emc.com.tw>
+ * Version: 1.5.5
+ *
+ * Based on cyapa driver:
+ * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
+ * copyright (c) 2011-2012 Google, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Trademarks are the property of their respective owners.
+ */
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/firmware.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/input/mt.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/input.h>
+#include <linux/uaccess.h>
+#include <linux/jiffies.h>
+#include <linux/completion.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+#include <asm/unaligned.h>
+
+#include "elan_i2c.h"
+
+#define DRIVER_NAME		"elan_i2c"
+#define ELAN_DRIVER_VERSION	"1.5.5"
+#define ETP_PRESSURE_OFFSET	25
+#define ETP_MAX_PRESSURE	255
+#define ETP_FWIDTH_REDUCE	90
+#define ETP_FINGER_WIDTH	15
+#define ETP_RETRY_COUNT		3
+
+#define ETP_MAX_FINGERS		5
+#define ETP_FINGER_DATA_LEN	5
+#define ETP_REPORT_ID		0x5D
+#define ETP_REPORT_ID_OFFSET	2
+#define ETP_TOUCH_INFO_OFFSET	3
+#define ETP_FINGER_DATA_OFFSET	4
+#define ETP_MAX_REPORT_LEN	34
+
+/* The main device structure */
+struct elan_tp_data {
+	struct i2c_client	*client;
+	struct input_dev	*input;
+	struct regulator	*vcc;
+
+	const struct elan_transport_ops *ops;
+
+	/* for fw update */
+	struct completion	fw_completion;
+	bool			in_fw_update;
+
+	struct mutex		sysfs_mutex;
+
+	unsigned int		max_x;
+	unsigned int		max_y;
+	unsigned int		width_x;
+	unsigned int		width_y;
+	unsigned int		x_res;
+	unsigned int		y_res;
+
+	u8			product_id;
+	u8			fw_version;
+	u8			sm_version;
+	u8			iap_version;
+	u16			fw_checksum;
+
+	u8			mode;
+
+	bool			irq_wake;
+
+	u8			min_baseline;
+	u8			max_baseline;
+	bool			baseline_ready;
+};
+
+static int elan_enable_power(struct elan_tp_data *data)
+{
+	int repeat = ETP_RETRY_COUNT;
+	int error;
+
+	error = regulator_enable(data->vcc);
+	if (error) {
+		dev_err(&data->client->dev,
+			"Failed to enable regulator: %d\n", error);
+		return error;
+	}
+
+	do {
+		error = data->ops->power_control(data->client, true);
+		if (error >= 0)
+			return 0;
+
+		msleep(30);
+	} while (--repeat > 0);
+
+	return error;
+}
+
+static int elan_disable_power(struct elan_tp_data *data)
+{
+	int repeat = ETP_RETRY_COUNT;
+	int error;
+
+	do {
+		error = data->ops->power_control(data->client, false);
+		if (!error) {
+			error = regulator_disable(data->vcc);
+			if (error) {
+				dev_err(&data->client->dev,
+					"Failed to disable regulator: %d\n",
+					error);
+				/* Attempt to power the chip back up */
+				data->ops->power_control(data->client, true);
+				break;
+			}
+
+			return 0;
+		}
+
+		msleep(30);
+	} while (--repeat > 0);
+
+	return error;
+}
+
+static int elan_sleep(struct elan_tp_data *data)
+{
+	int repeat = ETP_RETRY_COUNT;
+	int error;
+
+	do {
+		error = data->ops->sleep_control(data->client, true);
+		if (!error)
+			return 0;
+
+		msleep(30);
+	} while (--repeat > 0);
+
+	return error;
+}
+
+static int __elan_initialize(struct elan_tp_data *data)
+{
+	struct i2c_client *client = data->client;
+	int error;
+
+	error = data->ops->initialize(client);
+	if (error) {
+		dev_err(&client->dev, "device initialize failed: %d\n", error);
+		return error;
+	}
+
+	data->mode |= ETP_ENABLE_ABS;
+	error = data->ops->set_mode(client, data->mode);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to switch to absolute mode: %d\n", error);
+		return error;
+	}
+
+	error = data->ops->sleep_control(client, false);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to wake device up: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_initialize(struct elan_tp_data *data)
+{
+	int repeat = ETP_RETRY_COUNT;
+	int error;
+
+	do {
+		error = __elan_initialize(data);
+		if (!error)
+			return 0;
+
+		repeat--;
+		msleep(30);
+	} while (--repeat > 0);
+
+	return error;
+}
+
+static int elan_query_device_info(struct elan_tp_data *data)
+{
+	int error;
+
+	error = data->ops->get_product_id(data->client, &data->product_id);
+	if (error)
+		return error;
+
+	error = data->ops->get_version(data->client, false, &data->fw_version);
+	if (error)
+		return error;
+
+	error = data->ops->get_checksum(data->client, false,
+					&data->fw_checksum);
+	if (error)
+		return error;
+
+	error = data->ops->get_sm_version(data->client, &data->sm_version);
+	if (error)
+		return error;
+
+	error = data->ops->get_version(data->client, true, &data->iap_version);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static unsigned int elan_convert_resolution(u8 val)
+{
+	/*
+	 * (value from firmware) * 10 + 790 = dpi
+	 *
+	 * We also have to convert dpi to dots/mm (*10/254 to avoid floating
+	 * point).
+	 */
+
+	return ((int)(char)val * 10 + 790) * 10 / 254;
+}
+
+static int elan_query_device_parameters(struct elan_tp_data *data)
+{
+	unsigned int x_traces, y_traces;
+	u8 hw_x_res, hw_y_res;
+	int error;
+
+	error = data->ops->get_max(data->client, &data->max_x, &data->max_y);
+	if (error)
+		return error;
+
+	error = data->ops->get_num_traces(data->client, &x_traces, &y_traces);
+	if (error)
+		return error;
+
+	data->width_x = data->max_x / x_traces;
+	data->width_y = data->max_y / y_traces;
+
+	error = data->ops->get_resolution(data->client, &hw_x_res, &hw_y_res);
+	if (error)
+		return error;
+
+	data->x_res = elan_convert_resolution(hw_x_res);
+	data->y_res = elan_convert_resolution(hw_y_res);
+
+	return 0;
+}
+
+/*
+ **********************************************************
+ * IAP firmware updater related routines
+ **********************************************************
+ */
+static int elan_write_fw_block(struct elan_tp_data *data,
+			       const u8 *page, u16 checksum, int idx)
+{
+	int retry = ETP_RETRY_COUNT;
+	int error;
+
+	do {
+		error = data->ops->write_fw_block(data->client,
+						  page, checksum, idx);
+		if (!error)
+			return 0;
+
+		dev_dbg(&data->client->dev,
+			"IAP retrying page %d (error: %d)\n", idx, error);
+	} while (--retry > 0);
+
+	return error;
+}
+
+static int __elan_update_firmware(struct elan_tp_data *data,
+				  const struct firmware *fw)
+{
+	struct i2c_client *client = data->client;
+	struct device *dev = &client->dev;
+	int i, j;
+	int error;
+	u16 iap_start_addr;
+	u16 boot_page_count;
+	u16 sw_checksum = 0, fw_checksum = 0;
+
+	error = data->ops->prepare_fw_update(client);
+	if (error)
+		return error;
+
+	iap_start_addr = get_unaligned_le16(&fw->data[ETP_IAP_START_ADDR * 2]);
+
+	boot_page_count = (iap_start_addr * 2) / ETP_FW_PAGE_SIZE;
+	for (i = boot_page_count; i < ETP_FW_PAGE_COUNT; i++) {
+		u16 checksum = 0;
+		const u8 *page = &fw->data[i * ETP_FW_PAGE_SIZE];
+
+		for (j = 0; j < ETP_FW_PAGE_SIZE; j += 2)
+			checksum += ((page[j + 1] << 8) | page[j]);
+
+		error = elan_write_fw_block(data, page, checksum, i);
+		if (error) {
+			dev_err(dev, "write page %d fail: %d\n", i, error);
+			return error;
+		}
+
+		sw_checksum += checksum;
+	}
+
+	/* Wait WDT reset and power on reset */
+	msleep(600);
+
+	error = data->ops->finish_fw_update(client, &data->fw_completion);
+	if (error)
+		return error;
+
+	error = data->ops->get_checksum(client, true, &fw_checksum);
+	if (error)
+		return error;
+
+	if (sw_checksum != fw_checksum) {
+		dev_err(dev, "checksum diff sw=[%04X], fw=[%04X]\n",
+			sw_checksum, fw_checksum);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int elan_update_firmware(struct elan_tp_data *data,
+				const struct firmware *fw)
+{
+	struct i2c_client *client = data->client;
+	int retval;
+
+	dev_dbg(&client->dev, "Starting firmware update....\n");
+
+	disable_irq(client->irq);
+	data->in_fw_update = true;
+
+	retval = __elan_update_firmware(data, fw);
+	if (retval) {
+		dev_err(&client->dev, "firmware update failed: %d\n", retval);
+		data->ops->iap_reset(client);
+	} else {
+		/* Reinitialize TP after fw is updated */
+		elan_initialize(data);
+		elan_query_device_info(data);
+	}
+
+	data->in_fw_update = false;
+	enable_irq(client->irq);
+
+	return retval;
+}
+
+/*
+ *******************************************************************
+ * SYSFS attributes
+ *******************************************************************
+ */
+static ssize_t elan_sysfs_read_fw_checksum(struct device *dev,
+					   struct device_attribute *attr,
+					   char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "0x%04x\n", data->fw_checksum);
+}
+
+static ssize_t elan_sysfs_read_product_id(struct device *dev,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d.0\n", data->product_id);
+}
+
+static ssize_t elan_sysfs_read_fw_ver(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d.0\n", data->fw_version);
+}
+
+static ssize_t elan_sysfs_read_sm_ver(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d.0\n", data->sm_version);
+}
+
+static ssize_t elan_sysfs_read_iap_ver(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d.0\n", data->iap_version);
+}
+
+static ssize_t elan_sysfs_update_fw(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	const struct firmware *fw;
+	int error;
+
+	error = request_firmware(&fw, ETP_FW_NAME, dev);
+	if (error) {
+		dev_err(dev, "cannot load firmware %s: %d\n",
+			ETP_FW_NAME, error);
+		return error;
+	}
+
+	/* Firmware must be exactly PAGE_NUM * PAGE_SIZE bytes */
+	if (fw->size != ETP_FW_SIZE) {
+		dev_err(dev, "invalid firmware size = %zu, expected %d.\n",
+			fw->size, ETP_FW_SIZE);
+		error = -EBADF;
+		goto out_release_fw;
+	}
+
+	error = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (error)
+		goto out_release_fw;
+
+	error = elan_update_firmware(data, fw);
+
+	mutex_unlock(&data->sysfs_mutex);
+
+out_release_fw:
+	release_firmware(fw);
+	return error ?: count;
+}
+
+static ssize_t calibrate_store(struct device *dev,
+			       struct device_attribute *attr,
+			       const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int tries = 20;
+	int retval;
+	int error;
+	u8 val[3];
+
+	retval = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (retval)
+		return retval;
+
+	disable_irq(client->irq);
+
+	data->mode |= ETP_ENABLE_CALIBRATE;
+	retval = data->ops->set_mode(client, data->mode);
+	if (retval) {
+		dev_err(dev, "failed to enable calibration mode: %d\n",
+			retval);
+		goto out;
+	}
+
+	retval = data->ops->calibrate(client);
+	if (retval) {
+		dev_err(dev, "failed to start calibration: %d\n",
+			retval);
+		goto out_disable_calibrate;
+	}
+
+	val[0] = 0xff;
+	do {
+		/* Wait 250ms before checking if calibration has completed. */
+		msleep(250);
+
+		retval = data->ops->calibrate_result(client, val);
+		if (retval)
+			dev_err(dev, "failed to check calibration result: %d\n",
+				retval);
+		else if (val[0] == 0)
+			break; /* calibration done */
+
+	} while (--tries);
+
+	if (tries == 0) {
+		dev_err(dev, "failed to calibrate. Timeout.\n");
+		retval = -ETIMEDOUT;
+	}
+
+out_disable_calibrate:
+	data->mode &= ~ETP_ENABLE_CALIBRATE;
+	error = data->ops->set_mode(data->client, data->mode);
+	if (error) {
+		dev_err(dev, "failed to disable calibration mode: %d\n",
+			error);
+		if (!retval)
+			retval = error;
+	}
+out:
+	enable_irq(client->irq);
+	mutex_unlock(&data->sysfs_mutex);
+	return retval ?: count;
+}
+
+static ssize_t elan_sysfs_read_mode(struct device *dev,
+				    struct device_attribute *attr,
+				    char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int error;
+	enum tp_mode mode;
+
+	error = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (error)
+		return error;
+
+	error = data->ops->iap_get_mode(data->client, &mode);
+
+	mutex_unlock(&data->sysfs_mutex);
+
+	if (error)
+		return error;
+
+	return sprintf(buf, "%d\n", (int)mode);
+}
+
+static DEVICE_ATTR(product_id, S_IRUGO, elan_sysfs_read_product_id, NULL);
+static DEVICE_ATTR(firmware_version, S_IRUGO, elan_sysfs_read_fw_ver, NULL);
+static DEVICE_ATTR(sample_version, S_IRUGO, elan_sysfs_read_sm_ver, NULL);
+static DEVICE_ATTR(iap_version, S_IRUGO, elan_sysfs_read_iap_ver, NULL);
+static DEVICE_ATTR(fw_checksum, S_IRUGO, elan_sysfs_read_fw_checksum, NULL);
+static DEVICE_ATTR(mode, S_IRUGO, elan_sysfs_read_mode, NULL);
+static DEVICE_ATTR(update_fw, S_IWUSR, NULL, elan_sysfs_update_fw);
+
+static DEVICE_ATTR_WO(calibrate);
+
+static struct attribute *elan_sysfs_entries[] = {
+	&dev_attr_product_id.attr,
+	&dev_attr_firmware_version.attr,
+	&dev_attr_sample_version.attr,
+	&dev_attr_iap_version.attr,
+	&dev_attr_fw_checksum.attr,
+	&dev_attr_calibrate.attr,
+	&dev_attr_mode.attr,
+	&dev_attr_update_fw.attr,
+	NULL,
+};
+
+static const struct attribute_group elan_sysfs_group = {
+	.attrs = elan_sysfs_entries,
+};
+
+static ssize_t acquire_store(struct device *dev, struct device_attribute *attr,
+			     const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int error;
+	int retval;
+
+	retval = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (retval)
+		return retval;
+
+	disable_irq(client->irq);
+
+	data->baseline_ready = false;
+
+	data->mode |= ETP_ENABLE_CALIBRATE;
+	retval = data->ops->set_mode(data->client, data->mode);
+	if (retval) {
+		dev_err(dev, "Failed to enable calibration mode to get baseline: %d\n",
+			retval);
+		goto out;
+	}
+
+	msleep(250);
+
+	retval = data->ops->get_baseline_data(data->client, true,
+					      &data->max_baseline);
+	if (retval) {
+		dev_err(dev, "Failed to read max baseline form device: %d\n",
+			retval);
+		goto out_disable_calibrate;
+	}
+
+	retval = data->ops->get_baseline_data(data->client, false,
+					      &data->min_baseline);
+	if (retval) {
+		dev_err(dev, "Failed to read min baseline form device: %d\n",
+			retval);
+		goto out_disable_calibrate;
+	}
+
+	data->baseline_ready = true;
+
+out_disable_calibrate:
+	data->mode &= ~ETP_ENABLE_CALIBRATE;
+	error = data->ops->set_mode(data->client, data->mode);
+	if (error) {
+		dev_err(dev, "Failed to disable calibration mode after acquiring baseline: %d\n",
+			error);
+		if (!retval)
+			retval = error;
+	}
+out:
+	enable_irq(client->irq);
+	mutex_unlock(&data->sysfs_mutex);
+	return retval ?: count;
+}
+
+static ssize_t min_show(struct device *dev,
+			struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int retval;
+
+	retval = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (retval)
+		return retval;
+
+	if (!data->baseline_ready) {
+		retval = -ENODATA;
+		goto out;
+	}
+
+	retval = snprintf(buf, PAGE_SIZE, "%d", data->min_baseline);
+
+out:
+	mutex_unlock(&data->sysfs_mutex);
+	return retval;
+}
+
+static ssize_t max_show(struct device *dev,
+			struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int retval;
+
+	retval = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (retval)
+		return retval;
+
+	if (!data->baseline_ready) {
+		retval = -ENODATA;
+		goto out;
+	}
+
+	retval = snprintf(buf, PAGE_SIZE, "%d", data->max_baseline);
+
+out:
+	mutex_unlock(&data->sysfs_mutex);
+	return retval;
+}
+
+
+static DEVICE_ATTR_WO(acquire);
+static DEVICE_ATTR_RO(min);
+static DEVICE_ATTR_RO(max);
+
+static struct attribute *elan_baseline_sysfs_entries[] = {
+	&dev_attr_acquire.attr,
+	&dev_attr_min.attr,
+	&dev_attr_max.attr,
+	NULL,
+};
+
+static const struct attribute_group elan_baseline_sysfs_group = {
+	.name = "baseline",
+	.attrs = elan_baseline_sysfs_entries,
+};
+
+static const struct attribute_group *elan_sysfs_groups[] = {
+	&elan_sysfs_group,
+	&elan_baseline_sysfs_group,
+	NULL
+};
+
+/*
+ ******************************************************************
+ * Elan isr functions
+ ******************************************************************
+ */
+static void elan_report_contact(struct elan_tp_data *data,
+				int contact_num, bool contact_valid,
+				u8 *finger_data)
+{
+	struct input_dev *input = data->input;
+	unsigned int pos_x, pos_y;
+	unsigned int pressure, mk_x, mk_y;
+	unsigned int area_x, area_y, major, minor, new_pressure;
+
+
+	if (contact_valid) {
+		pos_x = ((finger_data[0] & 0xf0) << 4) |
+						finger_data[1];
+		pos_y = ((finger_data[0] & 0x0f) << 8) |
+						finger_data[2];
+		mk_x = (finger_data[3] & 0x0f);
+		mk_y = (finger_data[3] >> 4);
+		pressure = finger_data[4];
+
+		if (pos_x > data->max_x || pos_y > data->max_y) {
+			dev_dbg(input->dev.parent,
+				"[%d] x=%d y=%d over max (%d, %d)",
+				contact_num, pos_x, pos_y,
+				data->max_x, data->max_y);
+			return;
+		}
+
+		/*
+		 * To avoid treating large finger as palm, let's reduce the
+		 * width x and y per trace.
+		 */
+		area_x = mk_x * (data->width_x - ETP_FWIDTH_REDUCE);
+		area_y = mk_y * (data->width_y - ETP_FWIDTH_REDUCE);
+
+		major = max(area_x, area_y);
+		minor = min(area_x, area_y);
+
+		new_pressure = pressure + ETP_PRESSURE_OFFSET;
+		if (new_pressure > ETP_MAX_PRESSURE)
+			new_pressure = ETP_MAX_PRESSURE;
+
+		input_mt_slot(input, contact_num);
+		input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+		input_report_abs(input, ABS_MT_POSITION_X, pos_x);
+		input_report_abs(input, ABS_MT_POSITION_Y, data->max_y - pos_y);
+		input_report_abs(input, ABS_MT_PRESSURE, new_pressure);
+		input_report_abs(input, ABS_TOOL_WIDTH, mk_x);
+		input_report_abs(input, ABS_MT_TOUCH_MAJOR, major);
+		input_report_abs(input, ABS_MT_TOUCH_MINOR, minor);
+	} else {
+		input_mt_slot(input, contact_num);
+		input_mt_report_slot_state(input, MT_TOOL_FINGER, false);
+	}
+}
+
+static void elan_report_absolute(struct elan_tp_data *data, u8 *packet)
+{
+	struct input_dev *input = data->input;
+	u8 *finger_data = &packet[ETP_FINGER_DATA_OFFSET];
+	int i;
+	u8 tp_info = packet[ETP_TOUCH_INFO_OFFSET];
+	bool contact_valid;
+
+	for (i = 0; i < ETP_MAX_FINGERS; i++) {
+		contact_valid = tp_info & (1U << (3 + i));
+		elan_report_contact(data, i, contact_valid, finger_data);
+
+		if (contact_valid)
+			finger_data += ETP_FINGER_DATA_LEN;
+	}
+
+	input_report_key(input, BTN_LEFT, tp_info & 0x01);
+	input_mt_report_pointer_emulation(input, true);
+	input_sync(input);
+}
+
+static irqreturn_t elan_isr(int irq, void *dev_id)
+{
+	struct elan_tp_data *data = dev_id;
+	struct device *dev = &data->client->dev;
+	int error;
+	u8 report[ETP_MAX_REPORT_LEN];
+
+	/*
+	 * When device is connected to i2c bus, when all IAP page writes
+	 * complete, the driver will receive interrupt and must read
+	 * 0000 to confirm that IAP is finished.
+	*/
+	if (data->in_fw_update) {
+		complete(&data->fw_completion);
+		goto out;
+	}
+
+	error = data->ops->get_report(data->client, report);
+	if (error)
+		goto out;
+
+	if (report[ETP_REPORT_ID_OFFSET] != ETP_REPORT_ID)
+		dev_err(dev, "invalid report id data (%x)\n",
+			report[ETP_REPORT_ID_OFFSET]);
+	else
+		elan_report_absolute(data, report);
+
+out:
+	return IRQ_HANDLED;
+}
+
+/*
+ ******************************************************************
+ * Elan initialization functions
+ ******************************************************************
+ */
+static int elan_setup_input_device(struct elan_tp_data *data)
+{
+	struct device *dev = &data->client->dev;
+	struct input_dev *input;
+	unsigned int max_width = max(data->width_x, data->width_y);
+	unsigned int min_width = min(data->width_x, data->width_y);
+	int error;
+
+	input = devm_input_allocate_device(dev);
+	if (!input)
+		return -ENOMEM;
+
+	input->name = "Elan Touchpad";
+	input->id.bustype = BUS_I2C;
+	input_set_drvdata(input, data);
+
+	error = input_mt_init_slots(input, ETP_MAX_FINGERS,
+				    INPUT_MT_POINTER | INPUT_MT_DROP_UNUSED);
+	if (error) {
+		dev_err(dev, "failed to initialize MT slots: %d\n", error);
+		return error;
+	}
+
+	__set_bit(EV_ABS, input->evbit);
+	__set_bit(INPUT_PROP_POINTER, input->propbit);
+	__set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
+	__set_bit(BTN_LEFT, input->keybit);
+
+	/* Set up ST parameters */
+	input_set_abs_params(input, ABS_X, 0, data->max_x, 0, 0);
+	input_set_abs_params(input, ABS_Y, 0, data->max_y, 0, 0);
+	input_abs_set_res(input, ABS_X, data->x_res);
+	input_abs_set_res(input, ABS_Y, data->y_res);
+	input_set_abs_params(input, ABS_PRESSURE, 0, ETP_MAX_PRESSURE, 0, 0);
+	input_set_abs_params(input, ABS_TOOL_WIDTH, 0, ETP_FINGER_WIDTH, 0, 0);
+
+	/* And MT parameters */
+	input_set_abs_params(input, ABS_MT_POSITION_X, 0, data->max_x, 0, 0);
+	input_set_abs_params(input, ABS_MT_POSITION_Y, 0, data->max_y, 0, 0);
+	input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+	input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
+	input_set_abs_params(input, ABS_MT_PRESSURE, 0,
+			     ETP_MAX_PRESSURE, 0, 0);
+	input_set_abs_params(input, ABS_MT_TOUCH_MAJOR, 0,
+			     ETP_FINGER_WIDTH * max_width, 0, 0);
+	input_set_abs_params(input, ABS_MT_TOUCH_MINOR, 0,
+			     ETP_FINGER_WIDTH * min_width, 0, 0);
+
+	data->input = input;
+
+	return 0;
+}
+
+static void elan_disable_regulator(void *_data)
+{
+	struct elan_tp_data *data = _data;
+
+	regulator_disable(data->vcc);
+}
+
+static void elan_remove_sysfs_groups(void *_data)
+{
+	struct elan_tp_data *data = _data;
+
+	sysfs_remove_groups(&data->client->dev.kobj, elan_sysfs_groups);
+}
+
+static int elan_probe(struct i2c_client *client,
+		      const struct i2c_device_id *dev_id)
+{
+	const struct elan_transport_ops *transport_ops;
+	struct device *dev = &client->dev;
+	struct elan_tp_data *data;
+	unsigned long irqflags;
+	int error;
+
+	if (IS_ENABLED(CONFIG_MOUSE_ELAN_I2C_I2C) &&
+	    i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		transport_ops = &elan_i2c_ops;
+	} else if (IS_ENABLED(CONFIG_MOUSE_ELAN_I2C_SMBUS) &&
+		   i2c_check_functionality(client->adapter,
+					   I2C_FUNC_SMBUS_BYTE_DATA |
+						I2C_FUNC_SMBUS_BLOCK_DATA |
+						I2C_FUNC_SMBUS_I2C_BLOCK)) {
+		transport_ops = &elan_smbus_ops;
+	} else {
+		dev_err(dev, "not a supported I2C/SMBus adapter\n");
+		return -EIO;
+	}
+
+	data = devm_kzalloc(&client->dev, sizeof(struct elan_tp_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, data);
+
+	data->ops = transport_ops;
+	data->client = client;
+	init_completion(&data->fw_completion);
+	mutex_init(&data->sysfs_mutex);
+
+	data->vcc = devm_regulator_get(&client->dev, "vcc");
+	if (IS_ERR(data->vcc)) {
+		error = PTR_ERR(data->vcc);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"Failed to get 'vcc' regulator: %d\n",
+				error);
+		return error;
+	}
+
+	error = regulator_enable(data->vcc);
+	if (error) {
+		dev_err(&client->dev,
+			"Failed to enable regulator: %d\n", error);
+		return error;
+	}
+
+	error = devm_add_action(&client->dev,
+				elan_disable_regulator, data);
+	if (error) {
+		regulator_disable(data->vcc);
+		dev_err(&client->dev,
+			"Failed to add disable regulator action: %d\n",
+			error);
+		return error;
+	}
+
+	/* Initialize the touchpad. */
+	error = elan_initialize(data);
+	if (error)
+		return error;
+
+	error = elan_query_device_info(data);
+	if (error)
+		return error;
+
+	error = elan_query_device_parameters(data);
+	if (error)
+		return error;
+
+	dev_dbg(&client->dev,
+		"Elan Touchpad Information:\n"
+		"    Module product ID:  0x%04x\n"
+		"    Firmware Version:  0x%04x\n"
+		"    Sample Version:  0x%04x\n"
+		"    IAP Version:  0x%04x\n"
+		"    Max ABS X,Y:   %d,%d\n"
+		"    Width X,Y:   %d,%d\n"
+		"    Resolution X,Y:   %d,%d (dots/mm)\n",
+		data->product_id,
+		data->fw_version,
+		data->sm_version,
+		data->iap_version,
+		data->max_x, data->max_y,
+		data->width_x, data->width_y,
+		data->x_res, data->y_res);
+
+	/* Set up input device properties based on queried parameters. */
+	error = elan_setup_input_device(data);
+	if (error)
+		return error;
+
+	/*
+	 * Systems using device tree should set up interrupt via DTS,
+	 * the rest will use the default falling edge interrupts.
+	 */
+	irqflags = client->dev.of_node ? 0 : IRQF_TRIGGER_FALLING;
+
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, elan_isr,
+					  irqflags | IRQF_ONESHOT,
+					  client->name, data);
+	if (error) {
+		dev_err(&client->dev, "cannot register irq=%d\n", client->irq);
+		return error;
+	}
+
+	error = sysfs_create_groups(&client->dev.kobj, elan_sysfs_groups);
+	if (error) {
+		dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
+			error);
+		return error;
+	}
+
+	error = devm_add_action(&client->dev,
+				elan_remove_sysfs_groups, data);
+	if (error) {
+		elan_remove_sysfs_groups(data);
+		dev_err(&client->dev,
+			"Failed to add sysfs cleanup action: %d\n",
+			error);
+		return error;
+	}
+
+	error = input_register_device(data->input);
+	if (error) {
+		dev_err(&client->dev, "failed to register input device: %d\n",
+			error);
+		return error;
+	}
+
+	/*
+	 * Systems using device tree should set up wakeup via DTS,
+	 * the rest will configure device as wakeup source by default.
+	 */
+	if (!client->dev.of_node)
+		device_init_wakeup(&client->dev, true);
+
+	return 0;
+}
+
+static int __maybe_unused elan_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int ret;
+
+	/*
+	 * We are taking the mutex to make sure sysfs operations are
+	 * complete before we attempt to bring the device into low[er]
+	 * power mode.
+	 */
+	ret = mutex_lock_interruptible(&data->sysfs_mutex);
+	if (ret)
+		return ret;
+
+	disable_irq(client->irq);
+
+	if (device_may_wakeup(dev)) {
+		ret = elan_sleep(data);
+		/* Enable wake from IRQ */
+		data->irq_wake = (enable_irq_wake(client->irq) == 0);
+	} else {
+		ret = elan_disable_power(data);
+	}
+
+	mutex_unlock(&data->sysfs_mutex);
+	return ret;
+}
+
+static int __maybe_unused elan_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elan_tp_data *data = i2c_get_clientdata(client);
+	int error;
+
+	if (device_may_wakeup(dev) && data->irq_wake) {
+		disable_irq_wake(client->irq);
+		data->irq_wake = false;
+	}
+
+	error = elan_enable_power(data);
+	if (error)
+		dev_err(dev, "power up when resuming failed: %d\n", error);
+
+	error = elan_initialize(data);
+	if (error)
+		dev_err(dev, "initialize when resuming failed: %d\n", error);
+
+	enable_irq(data->client->irq);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(elan_pm_ops, elan_suspend, elan_resume);
+
+static const struct i2c_device_id elan_id[] = {
+	{ DRIVER_NAME, 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, elan_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id elan_acpi_id[] = {
+	{ "ELAN0000", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, elan_acpi_id);
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id elan_of_match[] = {
+	{ .compatible = "elan,ekth3000" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, elan_of_match);
+#endif
+
+static struct i2c_driver elan_driver = {
+	.driver = {
+		.name	= DRIVER_NAME,
+		.owner	= THIS_MODULE,
+		.pm	= &elan_pm_ops,
+		.acpi_match_table = ACPI_PTR(elan_acpi_id),
+		.of_match_table = of_match_ptr(elan_of_match),
+	},
+	.probe		= elan_probe,
+	.id_table	= elan_id,
+};
+
+module_i2c_driver(elan_driver);
+
+MODULE_AUTHOR("Duson Lin <dusonlin@emc.com.tw>");
+MODULE_DESCRIPTION("Elan I2C/SMBus Touchpad driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(ELAN_DRIVER_VERSION);
diff --git a/drivers/input/mouse/elan_i2c_i2c.c b/drivers/input/mouse/elan_i2c_i2c.c
new file mode 100644
index 0000000..97d4937
--- /dev/null
+++ b/drivers/input/mouse/elan_i2c_i2c.c
@@ -0,0 +1,611 @@
+/*
+ * Elan I2C/SMBus Touchpad driver - I2C interface
+ *
+ * Copyright (c) 2013 ELAN Microelectronics Corp.
+ *
+ * Author: 林政維 (Duson Lin) <dusonlin@emc.com.tw>
+ * Version: 1.5.5
+ *
+ * Based on cyapa driver:
+ * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
+ * copyright (c) 2011-2012 Google, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Trademarks are the property of their respective owners.
+ */
+
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <asm/unaligned.h>
+
+#include "elan_i2c.h"
+
+/* Elan i2c commands */
+#define ETP_I2C_RESET			0x0100
+#define ETP_I2C_WAKE_UP			0x0800
+#define ETP_I2C_SLEEP			0x0801
+#define ETP_I2C_DESC_CMD		0x0001
+#define ETP_I2C_REPORT_DESC_CMD		0x0002
+#define ETP_I2C_STAND_CMD		0x0005
+#define ETP_I2C_UNIQUEID_CMD		0x0101
+#define ETP_I2C_FW_VERSION_CMD		0x0102
+#define ETP_I2C_SM_VERSION_CMD		0x0103
+#define ETP_I2C_XY_TRACENUM_CMD		0x0105
+#define ETP_I2C_MAX_X_AXIS_CMD		0x0106
+#define ETP_I2C_MAX_Y_AXIS_CMD		0x0107
+#define ETP_I2C_RESOLUTION_CMD		0x0108
+#define ETP_I2C_IAP_VERSION_CMD		0x0110
+#define ETP_I2C_SET_CMD			0x0300
+#define ETP_I2C_POWER_CMD		0x0307
+#define ETP_I2C_FW_CHECKSUM_CMD		0x030F
+#define ETP_I2C_IAP_CTRL_CMD		0x0310
+#define ETP_I2C_IAP_CMD			0x0311
+#define ETP_I2C_IAP_RESET_CMD		0x0314
+#define ETP_I2C_IAP_CHECKSUM_CMD	0x0315
+#define ETP_I2C_CALIBRATE_CMD		0x0316
+#define ETP_I2C_MAX_BASELINE_CMD	0x0317
+#define ETP_I2C_MIN_BASELINE_CMD	0x0318
+
+#define ETP_I2C_REPORT_LEN		34
+#define ETP_I2C_DESC_LENGTH		30
+#define ETP_I2C_REPORT_DESC_LENGTH	158
+#define ETP_I2C_INF_LENGTH		2
+#define ETP_I2C_IAP_PASSWORD		0x1EA5
+#define ETP_I2C_IAP_RESET		0xF0F0
+#define ETP_I2C_MAIN_MODE_ON		(1 << 9)
+#define ETP_I2C_IAP_REG_L		0x01
+#define ETP_I2C_IAP_REG_H		0x06
+
+static int elan_i2c_read_block(struct i2c_client *client,
+			       u16 reg, u8 *val, u16 len)
+{
+	__le16 buf[] = {
+		cpu_to_le16(reg),
+	};
+	struct i2c_msg msgs[] = {
+		{
+			.addr = client->addr,
+			.flags = client->flags & I2C_M_TEN,
+			.len = sizeof(buf),
+			.buf = (u8 *)buf,
+		},
+		{
+			.addr = client->addr,
+			.flags = (client->flags & I2C_M_TEN) | I2C_M_RD,
+			.len = len,
+			.buf = val,
+		}
+	};
+	int ret;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	return ret == ARRAY_SIZE(msgs) ? 0 : (ret < 0 ? ret : -EIO);
+}
+
+static int elan_i2c_read_cmd(struct i2c_client *client, u16 reg, u8 *val)
+{
+	int retval;
+
+	retval = elan_i2c_read_block(client, reg, val, ETP_I2C_INF_LENGTH);
+	if (retval < 0) {
+		dev_err(&client->dev, "reading cmd (0x%04x) fail.\n", reg);
+		return retval;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_write_cmd(struct i2c_client *client, u16 reg, u16 cmd)
+{
+	__le16 buf[] = {
+		cpu_to_le16(reg),
+		cpu_to_le16(cmd),
+	};
+	struct i2c_msg msg = {
+		.addr = client->addr,
+		.flags = client->flags & I2C_M_TEN,
+		.len = sizeof(buf),
+		.buf = (u8 *)buf,
+	};
+	int ret;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	return ret == 1 ? 0 : (ret < 0 ? ret : -EIO);
+}
+
+static int elan_i2c_initialize(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	int error;
+	u8 val[256];
+
+	error = elan_i2c_write_cmd(client, ETP_I2C_STAND_CMD, ETP_I2C_RESET);
+	if (error) {
+		dev_err(dev, "device reset failed: %d\n", error);
+		return error;
+	}
+
+	/* Wait for the device to reset */
+	msleep(100);
+
+	/* get reset acknowledgement 0000 */
+	error = i2c_master_recv(client, val, ETP_I2C_INF_LENGTH);
+	if (error < 0) {
+		dev_err(dev, "failed to read reset response: %d\n", error);
+		return error;
+	}
+
+	error = elan_i2c_read_block(client, ETP_I2C_DESC_CMD,
+				    val, ETP_I2C_DESC_LENGTH);
+	if (error) {
+		dev_err(dev, "cannot get device descriptor: %d\n", error);
+		return error;
+	}
+
+	error = elan_i2c_read_block(client, ETP_I2C_REPORT_DESC_CMD,
+				    val, ETP_I2C_REPORT_DESC_LENGTH);
+	if (error) {
+		dev_err(dev, "fetching report descriptor failed.: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_sleep_control(struct i2c_client *client, bool sleep)
+{
+	return elan_i2c_write_cmd(client, ETP_I2C_STAND_CMD,
+				  sleep ? ETP_I2C_SLEEP : ETP_I2C_WAKE_UP);
+}
+
+static int elan_i2c_power_control(struct i2c_client *client, bool enable)
+{
+	u8 val[2];
+	u16 reg;
+	int error;
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_POWER_CMD, val);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to read current power state: %d\n",
+			error);
+		return error;
+	}
+
+	reg = le16_to_cpup((__le16 *)val);
+	if (enable)
+		reg &= ~ETP_DISABLE_POWER;
+	else
+		reg |= ETP_DISABLE_POWER;
+
+	error = elan_i2c_write_cmd(client, ETP_I2C_POWER_CMD, reg);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to write current power state: %d\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_set_mode(struct i2c_client *client, u8 mode)
+{
+	return elan_i2c_write_cmd(client, ETP_I2C_SET_CMD, mode);
+}
+
+
+static int elan_i2c_calibrate(struct i2c_client *client)
+{
+	return elan_i2c_write_cmd(client, ETP_I2C_CALIBRATE_CMD, 1);
+}
+
+static int elan_i2c_calibrate_result(struct i2c_client *client, u8 *val)
+{
+	return elan_i2c_read_block(client, ETP_I2C_CALIBRATE_CMD, val, 1);
+}
+
+static int elan_i2c_get_baseline_data(struct i2c_client *client,
+				      bool max_baseline, u8 *value)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client,
+				  max_baseline ? ETP_I2C_MAX_BASELINE_CMD :
+						 ETP_I2C_MIN_BASELINE_CMD,
+				  val);
+	if (error)
+		return error;
+
+	*value = le16_to_cpup((__le16 *)val);
+
+	return 0;
+}
+
+static int elan_i2c_get_version(struct i2c_client *client,
+				bool iap, u8 *version)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client,
+				  iap ? ETP_I2C_IAP_VERSION_CMD :
+					ETP_I2C_FW_VERSION_CMD,
+				  val);
+	if (error) {
+		dev_err(&client->dev, "failed to get %s version: %d\n",
+			iap ? "IAP" : "FW", error);
+		return error;
+	}
+
+	*version = val[0];
+	return 0;
+}
+
+static int elan_i2c_get_sm_version(struct i2c_client *client, u8 *version)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_SM_VERSION_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get SM version: %d\n", error);
+		return error;
+	}
+
+	*version = val[0];
+	return 0;
+}
+
+static int elan_i2c_get_product_id(struct i2c_client *client, u8 *id)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_UNIQUEID_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get product ID: %d\n", error);
+		return error;
+	}
+
+	*id = val[0];
+	return 0;
+}
+
+static int elan_i2c_get_checksum(struct i2c_client *client,
+				 bool iap, u16 *csum)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client,
+				  iap ? ETP_I2C_IAP_CHECKSUM_CMD :
+					ETP_I2C_FW_CHECKSUM_CMD,
+				  val);
+	if (error) {
+		dev_err(&client->dev, "failed to get %s checksum: %d\n",
+			iap ? "IAP" : "FW", error);
+		return error;
+	}
+
+	*csum = le16_to_cpup((__le16 *)val);
+	return 0;
+}
+
+static int elan_i2c_get_max(struct i2c_client *client,
+			    unsigned int *max_x, unsigned int *max_y)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_MAX_X_AXIS_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get X dimension: %d\n", error);
+		return error;
+	}
+
+	*max_x = le16_to_cpup((__le16 *)val) & 0x0fff;
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_MAX_Y_AXIS_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get Y dimension: %d\n", error);
+		return error;
+	}
+
+	*max_y = le16_to_cpup((__le16 *)val) & 0x0fff;
+
+	return 0;
+}
+
+static int elan_i2c_get_resolution(struct i2c_client *client,
+				   u8 *hw_res_x, u8 *hw_res_y)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_RESOLUTION_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get resolution: %d\n", error);
+		return error;
+	}
+
+	*hw_res_x = val[0];
+	*hw_res_y = val[1];
+
+	return 0;
+}
+
+static int elan_i2c_get_num_traces(struct i2c_client *client,
+				   unsigned int *x_traces,
+				   unsigned int *y_traces)
+{
+	int error;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_XY_TRACENUM_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get trace info: %d\n", error);
+		return error;
+	}
+
+	*x_traces = val[0] - 1;
+	*y_traces = val[1] - 1;
+
+	return 0;
+}
+
+static int elan_i2c_iap_get_mode(struct i2c_client *client, enum tp_mode *mode)
+{
+	int error;
+	u16 constant;
+	u8 val[3];
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_IAP_CTRL_CMD, val);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to read iap control register: %d\n",
+			error);
+		return error;
+	}
+
+	constant = le16_to_cpup((__le16 *)val);
+	dev_dbg(&client->dev, "iap control reg: 0x%04x.\n", constant);
+
+	*mode = (constant & ETP_I2C_MAIN_MODE_ON) ? MAIN_MODE : IAP_MODE;
+
+	return 0;
+}
+
+static int elan_i2c_iap_reset(struct i2c_client *client)
+{
+	int error;
+
+	error = elan_i2c_write_cmd(client, ETP_I2C_IAP_RESET_CMD,
+				   ETP_I2C_IAP_RESET);
+	if (error) {
+		dev_err(&client->dev, "cannot reset IC: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_set_flash_key(struct i2c_client *client)
+{
+	int error;
+
+	error = elan_i2c_write_cmd(client, ETP_I2C_IAP_CMD,
+				   ETP_I2C_IAP_PASSWORD);
+	if (error) {
+		dev_err(&client->dev, "cannot set flash key: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_prepare_fw_update(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	int error;
+	enum tp_mode mode;
+	u8 val[3];
+	u16 password;
+
+	/* Get FW in which mode	(IAP_MODE/MAIN_MODE)  */
+	error = elan_i2c_iap_get_mode(client, &mode);
+	if (error)
+		return error;
+
+	if (mode == IAP_MODE) {
+		/* Reset IC */
+		error = elan_i2c_iap_reset(client);
+		if (error)
+			return error;
+
+		msleep(30);
+	}
+
+	/* Set flash key*/
+	error = elan_i2c_set_flash_key(client);
+	if (error)
+		return error;
+
+	/* Wait for F/W IAP initialization */
+	msleep(mode == MAIN_MODE ? 100 : 30);
+
+	/* Check if we are in IAP mode or not */
+	error = elan_i2c_iap_get_mode(client, &mode);
+	if (error)
+		return error;
+
+	if (mode == MAIN_MODE) {
+		dev_err(dev, "wrong mode: %d\n", mode);
+		return -EIO;
+	}
+
+	/* Set flash key again */
+	error = elan_i2c_set_flash_key(client);
+	if (error)
+		return error;
+
+	/* Wait for F/W IAP initialization */
+	msleep(30);
+
+	/* read back to check we actually enabled successfully. */
+	error = elan_i2c_read_cmd(client, ETP_I2C_IAP_CMD, val);
+	if (error) {
+		dev_err(dev, "cannot read iap password: %d\n",
+			error);
+		return error;
+	}
+
+	password = le16_to_cpup((__le16 *)val);
+	if (password != ETP_I2C_IAP_PASSWORD) {
+		dev_err(dev, "wrong iap password: 0x%X\n", password);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_write_fw_block(struct i2c_client *client,
+				   const u8 *page, u16 checksum, int idx)
+{
+	struct device *dev = &client->dev;
+	u8 page_store[ETP_FW_PAGE_SIZE + 4];
+	u8 val[3];
+	u16 result;
+	int ret, error;
+
+	page_store[0] = ETP_I2C_IAP_REG_L;
+	page_store[1] = ETP_I2C_IAP_REG_H;
+	memcpy(&page_store[2], page, ETP_FW_PAGE_SIZE);
+	/* recode checksum at last two bytes */
+	put_unaligned_le16(checksum, &page_store[ETP_FW_PAGE_SIZE + 2]);
+
+	ret = i2c_master_send(client, page_store, sizeof(page_store));
+	if (ret != sizeof(page_store)) {
+		error = ret < 0 ? ret : -EIO;
+		dev_err(dev, "Failed to write page %d: %d\n", idx, error);
+		return error;
+	}
+
+	/* Wait for F/W to update one page ROM data. */
+	msleep(20);
+
+	error = elan_i2c_read_cmd(client, ETP_I2C_IAP_CTRL_CMD, val);
+	if (error) {
+		dev_err(dev, "Failed to read IAP write result: %d\n", error);
+		return error;
+	}
+
+	result = le16_to_cpup((__le16 *)val);
+	if (result & (ETP_FW_IAP_PAGE_ERR | ETP_FW_IAP_INTF_ERR)) {
+		dev_err(dev, "IAP reports failed write: %04hx\n",
+			result);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_finish_fw_update(struct i2c_client *client,
+				     struct completion *completion)
+{
+	struct device *dev = &client->dev;
+	long ret;
+	int error;
+	int len;
+	u8 buffer[ETP_I2C_INF_LENGTH];
+
+	reinit_completion(completion);
+	enable_irq(client->irq);
+
+	error = elan_i2c_write_cmd(client, ETP_I2C_STAND_CMD, ETP_I2C_RESET);
+	if (!error)
+		ret = wait_for_completion_interruptible_timeout(completion,
+							msecs_to_jiffies(300));
+	disable_irq(client->irq);
+
+	if (error) {
+		dev_err(dev, "device reset failed: %d\n", error);
+		return error;
+	} else if (ret == 0) {
+		dev_err(dev, "timeout waiting for device reset\n");
+		return -ETIMEDOUT;
+	} else if (ret < 0) {
+		error = ret;
+		dev_err(dev, "error waiting for device reset: %d\n", error);
+		return error;
+	}
+
+	len = i2c_master_recv(client, buffer, ETP_I2C_INF_LENGTH);
+	if (len != ETP_I2C_INF_LENGTH) {
+		error = len < 0 ? len : -EIO;
+		dev_err(dev, "failed to read INT signal: %d (%d)\n",
+			error, len);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_i2c_get_report(struct i2c_client *client, u8 *report)
+{
+	int len;
+
+	len = i2c_master_recv(client, report, ETP_I2C_REPORT_LEN);
+	if (len < 0) {
+		dev_err(&client->dev, "failed to read report data: %d\n", len);
+		return len;
+	}
+
+	if (len != ETP_I2C_REPORT_LEN) {
+		dev_err(&client->dev,
+			"wrong report length (%d vs %d expected)\n",
+			len, ETP_I2C_REPORT_LEN);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+const struct elan_transport_ops elan_i2c_ops = {
+	.initialize		= elan_i2c_initialize,
+	.sleep_control		= elan_i2c_sleep_control,
+	.power_control		= elan_i2c_power_control,
+	.set_mode		= elan_i2c_set_mode,
+
+	.calibrate		= elan_i2c_calibrate,
+	.calibrate_result	= elan_i2c_calibrate_result,
+
+	.get_baseline_data	= elan_i2c_get_baseline_data,
+
+	.get_version		= elan_i2c_get_version,
+	.get_sm_version		= elan_i2c_get_sm_version,
+	.get_product_id		= elan_i2c_get_product_id,
+	.get_checksum		= elan_i2c_get_checksum,
+
+	.get_max		= elan_i2c_get_max,
+	.get_resolution		= elan_i2c_get_resolution,
+	.get_num_traces		= elan_i2c_get_num_traces,
+
+	.iap_get_mode		= elan_i2c_iap_get_mode,
+	.iap_reset		= elan_i2c_iap_reset,
+
+	.prepare_fw_update	= elan_i2c_prepare_fw_update,
+	.write_fw_block		= elan_i2c_write_fw_block,
+	.finish_fw_update	= elan_i2c_finish_fw_update,
+
+	.get_report		= elan_i2c_get_report,
+};
diff --git a/drivers/input/mouse/elan_i2c_smbus.c b/drivers/input/mouse/elan_i2c_smbus.c
new file mode 100644
index 0000000..359bf85
--- /dev/null
+++ b/drivers/input/mouse/elan_i2c_smbus.c
@@ -0,0 +1,514 @@
+/*
+ * Elan I2C/SMBus Touchpad driver - SMBus interface
+ *
+ * Copyright (c) 2013 ELAN Microelectronics Corp.
+ *
+ * Author: 林政維 (Duson Lin) <dusonlin@emc.com.tw>
+ * Version: 1.5.5
+ *
+ * Based on cyapa driver:
+ * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
+ * copyright (c) 2011-2012 Google, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Trademarks are the property of their respective owners.
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include "elan_i2c.h"
+
+/* Elan SMbus commands */
+#define ETP_SMBUS_IAP_CMD		0x00
+#define ETP_SMBUS_ENABLE_TP		0x20
+#define ETP_SMBUS_SLEEP_CMD		0x21
+#define ETP_SMBUS_IAP_PASSWORD_WRITE	0x29
+#define ETP_SMBUS_IAP_PASSWORD_READ	0x80
+#define ETP_SMBUS_WRITE_FW_BLOCK	0x2A
+#define ETP_SMBUS_IAP_RESET_CMD		0x2B
+#define ETP_SMBUS_RANGE_CMD		0xA0
+#define ETP_SMBUS_FW_VERSION_CMD	0xA1
+#define ETP_SMBUS_XY_TRACENUM_CMD	0xA2
+#define ETP_SMBUS_SM_VERSION_CMD	0xA3
+#define ETP_SMBUS_UNIQUEID_CMD		0xA3
+#define ETP_SMBUS_RESOLUTION_CMD	0xA4
+#define ETP_SMBUS_HELLOPACKET_CMD	0xA7
+#define ETP_SMBUS_PACKET_QUERY		0xA8
+#define ETP_SMBUS_IAP_VERSION_CMD	0xAC
+#define ETP_SMBUS_IAP_CTRL_CMD		0xAD
+#define ETP_SMBUS_IAP_CHECKSUM_CMD	0xAE
+#define ETP_SMBUS_FW_CHECKSUM_CMD	0xAF
+#define ETP_SMBUS_MAX_BASELINE_CMD	0xC3
+#define ETP_SMBUS_MIN_BASELINE_CMD	0xC4
+#define ETP_SMBUS_CALIBRATE_QUERY	0xC5
+
+#define ETP_SMBUS_REPORT_LEN		32
+#define ETP_SMBUS_REPORT_OFFSET		2
+#define ETP_SMBUS_HELLOPACKET_LEN	5
+#define ETP_SMBUS_IAP_PASSWORD		0x1234
+#define ETP_SMBUS_IAP_MODE_ON		(1 << 6)
+
+static int elan_smbus_initialize(struct i2c_client *client)
+{
+	u8 check[ETP_SMBUS_HELLOPACKET_LEN] = { 0x55, 0x55, 0x55, 0x55, 0x55 };
+	u8 values[ETP_SMBUS_HELLOPACKET_LEN] = { 0, 0, 0, 0, 0 };
+	int len, error;
+
+	/* Get hello packet */
+	len = i2c_smbus_read_block_data(client,
+					ETP_SMBUS_HELLOPACKET_CMD, values);
+	if (len != ETP_SMBUS_HELLOPACKET_LEN) {
+		dev_err(&client->dev, "hello packet length fail: %d\n", len);
+		error = len < 0 ? len : -EIO;
+		return error;
+	}
+
+	/* compare hello packet */
+	if (memcmp(values, check, ETP_SMBUS_HELLOPACKET_LEN)) {
+		dev_err(&client->dev, "hello packet fail [%*px]\n",
+			ETP_SMBUS_HELLOPACKET_LEN, values);
+		return -ENXIO;
+	}
+
+	/* enable tp */
+	error = i2c_smbus_write_byte(client, ETP_SMBUS_ENABLE_TP);
+	if (error) {
+		dev_err(&client->dev, "failed to enable touchpad: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_smbus_set_mode(struct i2c_client *client, u8 mode)
+{
+	u8 cmd[4] = { 0x00, 0x07, 0x00, mode };
+
+	return i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
+					  sizeof(cmd), cmd);
+}
+
+static int elan_smbus_sleep_control(struct i2c_client *client, bool sleep)
+{
+	if (sleep)
+		return i2c_smbus_write_byte(client, ETP_SMBUS_SLEEP_CMD);
+	else
+		return 0; /* XXX should we send ETP_SMBUS_ENABLE_TP here? */
+}
+
+static int elan_smbus_power_control(struct i2c_client *client, bool enable)
+{
+	return 0; /* A no-op */
+}
+
+static int elan_smbus_calibrate(struct i2c_client *client)
+{
+	u8 cmd[4] = { 0x00, 0x08, 0x00, 0x01 };
+
+	return i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
+					  sizeof(cmd), cmd);
+}
+
+static int elan_smbus_calibrate_result(struct i2c_client *client, u8 *val)
+{
+	int error;
+
+	error = i2c_smbus_read_block_data(client,
+					  ETP_SMBUS_CALIBRATE_QUERY, val);
+	if (error < 0)
+		return error;
+
+	return 0;
+}
+
+static int elan_smbus_get_baseline_data(struct i2c_client *client,
+					bool max_baseline, u8 *value)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  max_baseline ?
+						ETP_SMBUS_MAX_BASELINE_CMD :
+						ETP_SMBUS_MIN_BASELINE_CMD,
+					  val);
+	if (error < 0)
+		return error;
+
+	*value = be16_to_cpup((__be16 *)val);
+
+	return 0;
+}
+
+static int elan_smbus_get_version(struct i2c_client *client,
+				  bool iap, u8 *version)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  iap ? ETP_SMBUS_IAP_VERSION_CMD :
+						ETP_SMBUS_FW_VERSION_CMD,
+					  val);
+	if (error < 0) {
+		dev_err(&client->dev, "failed to get %s version: %d\n",
+			iap ? "IAP" : "FW", error);
+		return error;
+	}
+
+	*version = val[2];
+	return 0;
+}
+
+static int elan_smbus_get_sm_version(struct i2c_client *client, u8 *version)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  ETP_SMBUS_SM_VERSION_CMD, val);
+	if (error < 0) {
+		dev_err(&client->dev, "failed to get SM version: %d\n", error);
+		return error;
+	}
+
+	*version = val[0]; /* XXX Why 0 and not 2 as in IAP/FW versions? */
+	return 0;
+}
+
+static int elan_smbus_get_product_id(struct i2c_client *client, u8 *id)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  ETP_SMBUS_UNIQUEID_CMD, val);
+	if (error < 0) {
+		dev_err(&client->dev, "failed to get product ID: %d\n", error);
+		return error;
+	}
+
+	*id = val[1];
+	return 0;
+}
+
+static int elan_smbus_get_checksum(struct i2c_client *client,
+				   bool iap, u16 *csum)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  iap ? ETP_SMBUS_FW_CHECKSUM_CMD :
+						ETP_SMBUS_IAP_CHECKSUM_CMD,
+					  val);
+	if (error < 0) {
+		dev_err(&client->dev, "failed to get %s checksum: %d\n",
+			iap ? "IAP" : "FW", error);
+		return error;
+	}
+
+	*csum = be16_to_cpup((__be16 *)val);
+	return 0;
+}
+
+static int elan_smbus_get_max(struct i2c_client *client,
+			      unsigned int *max_x, unsigned int *max_y)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client, ETP_SMBUS_RANGE_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get dimensions: %d\n", error);
+		return error;
+	}
+
+	*max_x = (0x0f & val[0]) << 8 | val[1];
+	*max_y = (0xf0 & val[0]) << 4 | val[2];
+
+	return 0;
+}
+
+static int elan_smbus_get_resolution(struct i2c_client *client,
+				     u8 *hw_res_x, u8 *hw_res_y)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  ETP_SMBUS_RESOLUTION_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get resolution: %d\n", error);
+		return error;
+	}
+
+	*hw_res_x = val[1] & 0x0F;
+	*hw_res_y = (val[1] & 0xF0) >> 4;
+
+	return 0;
+}
+
+static int elan_smbus_get_num_traces(struct i2c_client *client,
+				     unsigned int *x_traces,
+				     unsigned int *y_traces)
+{
+	int error;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client,
+					  ETP_SMBUS_XY_TRACENUM_CMD, val);
+	if (error) {
+		dev_err(&client->dev, "failed to get trace info: %d\n", error);
+		return error;
+	}
+
+	*x_traces = val[1] - 1;
+	*y_traces = val[2] - 1;
+
+	return 0;
+}
+
+static int elan_smbus_iap_get_mode(struct i2c_client *client,
+				   enum tp_mode *mode)
+{
+	int error;
+	u16 constant;
+	u8 val[3];
+
+	error = i2c_smbus_read_block_data(client, ETP_SMBUS_IAP_CTRL_CMD, val);
+	if (error < 0) {
+		dev_err(&client->dev, "failed to read iap ctrol register: %d\n",
+			error);
+		return error;
+	}
+
+	constant = be16_to_cpup((__be16 *)val);
+	dev_dbg(&client->dev, "iap control reg: 0x%04x.\n", constant);
+
+	*mode = (constant & ETP_SMBUS_IAP_MODE_ON) ? IAP_MODE : MAIN_MODE;
+
+	return 0;
+}
+
+static int elan_smbus_iap_reset(struct i2c_client *client)
+{
+	int error;
+
+	error = i2c_smbus_write_byte(client, ETP_SMBUS_IAP_RESET_CMD);
+	if (error) {
+		dev_err(&client->dev, "cannot reset IC: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_smbus_set_flash_key(struct i2c_client *client)
+{
+	int error;
+	u8 cmd[4] = { 0x00, 0x0B, 0x00, 0x5A };
+
+	error = i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
+					   sizeof(cmd), cmd);
+	if (error) {
+		dev_err(&client->dev, "cannot set flash key: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int elan_smbus_prepare_fw_update(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	int len;
+	int error;
+	enum tp_mode mode;
+	u8 val[3];
+	u8 cmd[4] = {0x0F, 0x78, 0x00, 0x06};
+	u16 password;
+
+	/* Get FW in which mode	(IAP_MODE/MAIN_MODE)  */
+	error = elan_smbus_iap_get_mode(client, &mode);
+	if (error)
+		return error;
+
+	if (mode == MAIN_MODE) {
+
+		/* set flash key */
+		error = elan_smbus_set_flash_key(client);
+		if (error)
+			return error;
+
+		/* write iap password */
+		if (i2c_smbus_write_byte(client,
+					 ETP_SMBUS_IAP_PASSWORD_WRITE) < 0) {
+			dev_err(dev, "cannot write iap password\n");
+			return -EIO;
+		}
+
+		error = i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
+						   sizeof(cmd), cmd);
+		if (error) {
+			dev_err(dev, "failed to write iap password: %d\n",
+				error);
+			return error;
+		}
+
+		/*
+		 * Read back password to make sure we enabled flash
+		 * successfully.
+		 */
+		len = i2c_smbus_read_block_data(client,
+						ETP_SMBUS_IAP_PASSWORD_READ,
+						val);
+		if (len < sizeof(u16)) {
+			error = len < 0 ? len : -EIO;
+			dev_err(dev, "failed to read iap password: %d\n",
+				error);
+			return error;
+		}
+
+		password = be16_to_cpup((__be16 *)val);
+		if (password != ETP_SMBUS_IAP_PASSWORD) {
+			dev_err(dev, "wrong iap password = 0x%X\n", password);
+			return -EIO;
+		}
+
+		/* Wait 30ms for MAIN_MODE change to IAP_MODE */
+		msleep(30);
+	}
+
+	error = elan_smbus_set_flash_key(client);
+	if (error)
+		return error;
+
+	/* Reset IC */
+	error = elan_smbus_iap_reset(client);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+
+static int elan_smbus_write_fw_block(struct i2c_client *client,
+				     const u8 *page, u16 checksum, int idx)
+{
+	struct device *dev = &client->dev;
+	int error;
+	u16 result;
+	u8 val[3];
+
+	/*
+	 * Due to the limitation of smbus protocol limiting
+	 * transfer to 32 bytes at a time, we must split block
+	 * in 2 transfers.
+	 */
+	error = i2c_smbus_write_block_data(client,
+					   ETP_SMBUS_WRITE_FW_BLOCK,
+					   ETP_FW_PAGE_SIZE / 2,
+					   page);
+	if (error) {
+		dev_err(dev, "Failed to write page %d (part %d): %d\n",
+			idx, 1, error);
+		return error;
+	}
+
+	error = i2c_smbus_write_block_data(client,
+					   ETP_SMBUS_WRITE_FW_BLOCK,
+					   ETP_FW_PAGE_SIZE / 2,
+					   page + ETP_FW_PAGE_SIZE / 2);
+	if (error) {
+		dev_err(dev, "Failed to write page %d (part %d): %d\n",
+			idx, 2, error);
+		return error;
+	}
+
+
+	/* Wait for F/W to update one page ROM data. */
+	usleep_range(8000, 10000);
+
+	error = i2c_smbus_read_block_data(client,
+					  ETP_SMBUS_IAP_CTRL_CMD, val);
+	if (error < 0) {
+		dev_err(dev, "Failed to read IAP write result: %d\n",
+			error);
+		return error;
+	}
+
+	result = be16_to_cpup((__be16 *)val);
+	if (result & (ETP_FW_IAP_PAGE_ERR | ETP_FW_IAP_INTF_ERR)) {
+		dev_err(dev, "IAP reports failed write: %04hx\n",
+			result);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int elan_smbus_get_report(struct i2c_client *client, u8 *report)
+{
+	int len;
+
+	len = i2c_smbus_read_block_data(client,
+					ETP_SMBUS_PACKET_QUERY,
+					&report[ETP_SMBUS_REPORT_OFFSET]);
+	if (len < 0) {
+		dev_err(&client->dev, "failed to read report data: %d\n", len);
+		return len;
+	}
+
+	if (len != ETP_SMBUS_REPORT_LEN) {
+		dev_err(&client->dev,
+			"wrong report length (%d vs %d expected)\n",
+			len, ETP_SMBUS_REPORT_LEN);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int elan_smbus_finish_fw_update(struct i2c_client *client,
+				       struct completion *fw_completion)
+{
+	/* No special handling unlike I2C transport */
+	return 0;
+}
+
+const struct elan_transport_ops elan_smbus_ops = {
+	.initialize		= elan_smbus_initialize,
+	.sleep_control		= elan_smbus_sleep_control,
+	.power_control		= elan_smbus_power_control,
+	.set_mode		= elan_smbus_set_mode,
+
+	.calibrate		= elan_smbus_calibrate,
+	.calibrate_result	= elan_smbus_calibrate_result,
+
+	.get_baseline_data	= elan_smbus_get_baseline_data,
+
+	.get_version		= elan_smbus_get_version,
+	.get_sm_version		= elan_smbus_get_sm_version,
+	.get_product_id		= elan_smbus_get_product_id,
+	.get_checksum		= elan_smbus_get_checksum,
+
+	.get_max		= elan_smbus_get_max,
+	.get_resolution		= elan_smbus_get_resolution,
+	.get_num_traces		= elan_smbus_get_num_traces,
+
+	.iap_get_mode		= elan_smbus_iap_get_mode,
+	.iap_reset		= elan_smbus_iap_reset,
+
+	.prepare_fw_update	= elan_smbus_prepare_fw_update,
+	.write_fw_block		= elan_smbus_write_fw_block,
+	.finish_fw_update	= elan_smbus_finish_fw_update,
+
+	.get_report		= elan_smbus_get_report,
+};
diff --git a/drivers/input/mouse/lifebook.h b/drivers/input/mouse/lifebook.h
index 4c4326c..0baf02a 100644
--- a/drivers/input/mouse/lifebook.h
+++ b/drivers/input/mouse/lifebook.h
@@ -16,14 +16,14 @@
 int lifebook_detect(struct psmouse *psmouse, bool set_properties);
 int lifebook_init(struct psmouse *psmouse);
 #else
-inline void lifebook_module_init(void)
+static inline void lifebook_module_init(void)
 {
 }
-inline int lifebook_detect(struct psmouse *psmouse, bool set_properties)
+static inline int lifebook_detect(struct psmouse *psmouse, bool set_properties)
 {
 	return -ENOSYS;
 }
-inline int lifebook_init(struct psmouse *psmouse)
+static inline int lifebook_init(struct psmouse *psmouse)
 {
 	return -ENOSYS;
 }
diff --git a/drivers/input/mouse/navpoint.c b/drivers/input/mouse/navpoint.c
index 2a0360f..d6e8f58 100644
--- a/drivers/input/mouse/navpoint.c
+++ b/drivers/input/mouse/navpoint.c
@@ -318,8 +318,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int navpoint_suspend(struct device *dev)
+static int __maybe_unused navpoint_suspend(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct navpoint *navpoint = platform_get_drvdata(pdev);
@@ -333,7 +332,7 @@
 	return 0;
 }
 
-static int navpoint_resume(struct device *dev)
+static int __maybe_unused navpoint_resume(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct navpoint *navpoint = platform_get_drvdata(pdev);
@@ -346,7 +345,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(navpoint_pm_ops, navpoint_suspend, navpoint_resume);
 
diff --git a/drivers/input/mouse/synaptics_i2c.c b/drivers/input/mouse/synaptics_i2c.c
index ad82260..878f184 100644
--- a/drivers/input/mouse/synaptics_i2c.c
+++ b/drivers/input/mouse/synaptics_i2c.c
@@ -614,8 +614,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int synaptics_i2c_suspend(struct device *dev)
+static int __maybe_unused synaptics_i2c_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct synaptics_i2c *touch = i2c_get_clientdata(client);
@@ -628,7 +627,7 @@
 	return 0;
 }
 
-static int synaptics_i2c_resume(struct device *dev)
+static int __maybe_unused synaptics_i2c_resume(struct device *dev)
 {
 	int ret;
 	struct i2c_client *client = to_i2c_client(dev);
@@ -643,7 +642,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(synaptics_i2c_pm, synaptics_i2c_suspend,
 			 synaptics_i2c_resume);
diff --git a/drivers/input/serio/altera_ps2.c b/drivers/input/serio/altera_ps2.c
index 8921c96..131d782 100644
--- a/drivers/input/serio/altera_ps2.c
+++ b/drivers/input/serio/altera_ps2.c
@@ -24,9 +24,7 @@
 
 struct ps2if {
 	struct serio *io;
-	struct resource *iomem_res;
 	void __iomem *base;
-	unsigned irq;
 };
 
 /*
@@ -83,16 +81,34 @@
 static int altera_ps2_probe(struct platform_device *pdev)
 {
 	struct ps2if *ps2if;
+	struct resource *res;
 	struct serio *serio;
 	int error, irq;
 
-	ps2if = kzalloc(sizeof(struct ps2if), GFP_KERNEL);
-	serio = kzalloc(sizeof(struct serio), GFP_KERNEL);
-	if (!ps2if || !serio) {
-		error = -ENOMEM;
-		goto err_free_mem;
+	ps2if = devm_kzalloc(&pdev->dev, sizeof(struct ps2if), GFP_KERNEL);
+	if (!ps2if)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ps2if->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ps2if->base))
+		return PTR_ERR(ps2if->base);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return -ENXIO;
+
+	error = devm_request_irq(&pdev->dev, irq, altera_ps2_rxint, 0,
+				 pdev->name, ps2if);
+	if (error) {
+		dev_err(&pdev->dev, "could not request IRQ %d\n", irq);
+		return error;
 	}
 
+	serio = kzalloc(sizeof(struct serio), GFP_KERNEL);
+	if (!serio)
+		return -ENOMEM;
+
 	serio->id.type		= SERIO_8042;
 	serio->write		= altera_ps2_write;
 	serio->open		= altera_ps2_open;
@@ -103,56 +119,12 @@
 	serio->dev.parent	= &pdev->dev;
 	ps2if->io		= serio;
 
-	ps2if->iomem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (ps2if->iomem_res == NULL) {
-		error = -ENOENT;
-		goto err_free_mem;
-	}
-
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		error = -ENXIO;
-		goto err_free_mem;
-	}
-	ps2if->irq = irq;
-
-	if (!request_mem_region(ps2if->iomem_res->start,
-				resource_size(ps2if->iomem_res), pdev->name)) {
-		error = -EBUSY;
-		goto err_free_mem;
-	}
-
-	ps2if->base = ioremap(ps2if->iomem_res->start,
-			      resource_size(ps2if->iomem_res));
-	if (!ps2if->base) {
-		error = -ENOMEM;
-		goto err_free_res;
-	}
-
-	error = request_irq(ps2if->irq, altera_ps2_rxint, 0, pdev->name, ps2if);
-	if (error) {
-		dev_err(&pdev->dev, "could not allocate IRQ %d: %d\n",
-			ps2if->irq, error);
-		goto err_unmap;
-	}
-
-	dev_info(&pdev->dev, "base %p, irq %d\n", ps2if->base, ps2if->irq);
+	dev_info(&pdev->dev, "base %p, irq %d\n", ps2if->base, irq);
 
 	serio_register_port(ps2if->io);
 	platform_set_drvdata(pdev, ps2if);
 
 	return 0;
-
- err_unmap:
-	iounmap(ps2if->base);
- err_free_res:
-	release_mem_region(ps2if->iomem_res->start,
-			   resource_size(ps2if->iomem_res));
- err_free_mem:
-	kfree(ps2if);
-	kfree(serio);
-	return error;
 }
 
 /*
@@ -163,11 +135,6 @@
 	struct ps2if *ps2if = platform_get_drvdata(pdev);
 
 	serio_unregister_port(ps2if->io);
-	free_irq(ps2if->irq, ps2if);
-	iounmap(ps2if->base);
-	release_mem_region(ps2if->iomem_res->start,
-			   resource_size(ps2if->iomem_res));
-	kfree(ps2if);
 
 	return 0;
 }
diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h
index faeeb13..c66d1b5 100644
--- a/drivers/input/serio/i8042-x86ia64io.h
+++ b/drivers/input/serio/i8042-x86ia64io.h
@@ -579,6 +579,16 @@
 		},
 	},
 	{
+		/*
+		 * Intel NUC D54250WYK - does not have i8042 controller but
+		 * declares PS/2 devices in DSDT.
+		 */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "D54250WYK"),
+			DMI_MATCH(DMI_BOARD_VENDOR, "Intel Corporation"),
+		},
+	},
+	{
 		/* MSI Wind U-100 */
 		.matches = {
 			DMI_MATCH(DMI_BOARD_NAME, "U-100"),
diff --git a/drivers/input/serio/serio.c b/drivers/input/serio/serio.c
index d399b8b..a05a517 100644
--- a/drivers/input/serio/serio.c
+++ b/drivers/input/serio/serio.c
@@ -514,7 +514,7 @@
  */
 static void serio_init_port(struct serio *serio)
 {
-	static atomic_t serio_no = ATOMIC_INIT(0);
+	static atomic_t serio_no = ATOMIC_INIT(-1);
 
 	__module_get(THIS_MODULE);
 
@@ -525,7 +525,7 @@
 	mutex_init(&serio->drv_mutex);
 	device_initialize(&serio->dev);
 	dev_set_name(&serio->dev, "serio%lu",
-		     (unsigned long)atomic_inc_return(&serio_no) - 1);
+		     (unsigned long)atomic_inc_return(&serio_no));
 	serio->dev.bus = &serio_bus;
 	serio->dev.release = serio_release_port;
 	serio->dev.groups = serio_device_attr_groups;
diff --git a/drivers/input/serio/serio_raw.c b/drivers/input/serio/serio_raw.c
index c9a02fe..71ef5d6 100644
--- a/drivers/input/serio/serio_raw.c
+++ b/drivers/input/serio/serio_raw.c
@@ -292,7 +292,7 @@
 
 static int serio_raw_connect(struct serio *serio, struct serio_driver *drv)
 {
-	static atomic_t serio_raw_no = ATOMIC_INIT(0);
+	static atomic_t serio_raw_no = ATOMIC_INIT(-1);
 	struct serio_raw *serio_raw;
 	int err;
 
@@ -303,7 +303,7 @@
 	}
 
 	snprintf(serio_raw->name, sizeof(serio_raw->name),
-		 "serio_raw%ld", (long)atomic_inc_return(&serio_raw_no) - 1);
+		 "serio_raw%ld", (long)atomic_inc_return(&serio_raw_no));
 	kref_init(&serio_raw->kref);
 	INIT_LIST_HEAD(&serio_raw->client_list);
 	init_waitqueue_head(&serio_raw->wait);
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index e1d8003..5891752 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -295,6 +295,19 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called fujitsu-ts.
 
+config TOUCHSCREEN_GOODIX
+	tristate "Goodix I2C touchscreen"
+	depends on I2C && ACPI
+	help
+	  Say Y here if you have the Goodix touchscreen (such as one
+	  installed in Onda v975w tablets) connected to your
+	  system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called goodix.
+
 config TOUCHSCREEN_ILI210X
 	tristate "Ilitek ILI210X based touchscreen"
 	depends on I2C
@@ -334,6 +347,18 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called gunze.
 
+config TOUCHSCREEN_ELAN
+	tristate "Elan eKTH I2C touchscreen"
+	depends on I2C
+	help
+	  Say Y here if you have an Elan eKTH I2C touchscreen
+	  connected to your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called elants_i2c.
+
 config TOUCHSCREEN_ELO
 	tristate "Elo serial touchscreens"
 	select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 090e61c..0242fea 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -31,9 +31,11 @@
 obj-$(CONFIG_TOUCHSCREEN_HAMPSHIRE)	+= hampshire.o
 obj-$(CONFIG_TOUCHSCREEN_GUNZE)		+= gunze.o
 obj-$(CONFIG_TOUCHSCREEN_EETI)		+= eeti_ts.o
+obj-$(CONFIG_TOUCHSCREEN_ELAN)		+= elants_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ELO)		+= elo.o
 obj-$(CONFIG_TOUCHSCREEN_EGALAX)	+= egalax_ts.o
 obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
+obj-$(CONFIG_TOUCHSCREEN_GOODIX)	+= goodix.o
 obj-$(CONFIG_TOUCHSCREEN_ILI210X)	+= ili210x.o
 obj-$(CONFIG_TOUCHSCREEN_INEXIO)	+= inexio.o
 obj-$(CONFIG_TOUCHSCREEN_INTEL_MID)	+= intel-mid-touch.o
diff --git a/drivers/input/touchscreen/ad7877.c b/drivers/input/touchscreen/ad7877.c
index 523865d..da4e5bb 100644
--- a/drivers/input/touchscreen/ad7877.c
+++ b/drivers/input/touchscreen/ad7877.c
@@ -820,8 +820,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int ad7877_suspend(struct device *dev)
+static int __maybe_unused ad7877_suspend(struct device *dev)
 {
 	struct ad7877 *ts = dev_get_drvdata(dev);
 
@@ -830,7 +829,7 @@
 	return 0;
 }
 
-static int ad7877_resume(struct device *dev)
+static int __maybe_unused ad7877_resume(struct device *dev)
 {
 	struct ad7877 *ts = dev_get_drvdata(dev);
 
@@ -838,7 +837,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(ad7877_pm, ad7877_suspend, ad7877_resume);
 
diff --git a/drivers/input/touchscreen/ad7879.c b/drivers/input/touchscreen/ad7879.c
index 1eb9d3c..fec66ad 100644
--- a/drivers/input/touchscreen/ad7879.c
+++ b/drivers/input/touchscreen/ad7879.c
@@ -284,8 +284,7 @@
 		__ad7879_disable(ts);
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int ad7879_suspend(struct device *dev)
+static int __maybe_unused ad7879_suspend(struct device *dev)
 {
 	struct ad7879 *ts = dev_get_drvdata(dev);
 
@@ -301,7 +300,7 @@
 	return 0;
 }
 
-static int ad7879_resume(struct device *dev)
+static int __maybe_unused ad7879_resume(struct device *dev)
 {
 	struct ad7879 *ts = dev_get_drvdata(dev);
 
@@ -316,7 +315,6 @@
 
 	return 0;
 }
-#endif
 
 SIMPLE_DEV_PM_OPS(ad7879_pm_ops, ad7879_suspend, ad7879_resume);
 EXPORT_SYMBOL(ad7879_pm_ops);
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
index e57ba52..e4eb8a6 100644
--- a/drivers/input/touchscreen/ads7846.c
+++ b/drivers/input/touchscreen/ads7846.c
@@ -883,8 +883,7 @@
 	return IRQ_HANDLED;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int ads7846_suspend(struct device *dev)
+static int __maybe_unused ads7846_suspend(struct device *dev)
 {
 	struct ads7846 *ts = dev_get_drvdata(dev);
 
@@ -906,7 +905,7 @@
 	return 0;
 }
 
-static int ads7846_resume(struct device *dev)
+static int __maybe_unused ads7846_resume(struct device *dev)
 {
 	struct ads7846 *ts = dev_get_drvdata(dev);
 
@@ -927,7 +926,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(ads7846_pm, ads7846_suspend, ads7846_resume);
 
diff --git a/drivers/input/touchscreen/atmel_mxt_ts.c b/drivers/input/touchscreen/atmel_mxt_ts.c
index aaacf8b..bb07020 100644
--- a/drivers/input/touchscreen/atmel_mxt_ts.c
+++ b/drivers/input/touchscreen/atmel_mxt_ts.c
@@ -2244,8 +2244,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int mxt_suspend(struct device *dev)
+static int __maybe_unused mxt_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct mxt_data *data = i2c_get_clientdata(client);
@@ -2261,7 +2260,7 @@
 	return 0;
 }
 
-static int mxt_resume(struct device *dev)
+static int __maybe_unused mxt_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct mxt_data *data = i2c_get_clientdata(client);
@@ -2276,7 +2275,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(mxt_pm_ops, mxt_suspend, mxt_resume);
 
diff --git a/drivers/input/touchscreen/auo-pixcir-ts.c b/drivers/input/touchscreen/auo-pixcir-ts.c
index 7f3c947..40e02dd 100644
--- a/drivers/input/touchscreen/auo-pixcir-ts.c
+++ b/drivers/input/touchscreen/auo-pixcir-ts.c
@@ -417,8 +417,7 @@
 	return;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int auo_pixcir_suspend(struct device *dev)
+static int __maybe_unused auo_pixcir_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct auo_pixcir_ts *ts = i2c_get_clientdata(client);
@@ -450,7 +449,7 @@
 	return ret;
 }
 
-static int auo_pixcir_resume(struct device *dev)
+static int __maybe_unused auo_pixcir_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct auo_pixcir_ts *ts = i2c_get_clientdata(client);
@@ -479,7 +478,6 @@
 
 	return ret;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(auo_pixcir_pm_ops,
 			 auo_pixcir_suspend, auo_pixcir_resume);
diff --git a/drivers/input/touchscreen/cy8ctmg110_ts.c b/drivers/input/touchscreen/cy8ctmg110_ts.c
index 5bf1aee..f2119ee 100644
--- a/drivers/input/touchscreen/cy8ctmg110_ts.c
+++ b/drivers/input/touchscreen/cy8ctmg110_ts.c
@@ -291,8 +291,7 @@
 	return err;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int cy8ctmg110_suspend(struct device *dev)
+static int __maybe_unused cy8ctmg110_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct cy8ctmg110 *ts = i2c_get_clientdata(client);
@@ -306,7 +305,7 @@
 	return 0;
 }
 
-static int cy8ctmg110_resume(struct device *dev)
+static int __maybe_unused cy8ctmg110_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct cy8ctmg110 *ts = i2c_get_clientdata(client);
@@ -319,7 +318,6 @@
 	}
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(cy8ctmg110_pm, cy8ctmg110_suspend, cy8ctmg110_resume);
 
diff --git a/drivers/input/touchscreen/cyttsp_core.c b/drivers/input/touchscreen/cyttsp_core.c
index eee656f..5b74e8b 100644
--- a/drivers/input/touchscreen/cyttsp_core.c
+++ b/drivers/input/touchscreen/cyttsp_core.c
@@ -472,8 +472,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int cyttsp_suspend(struct device *dev)
+static int __maybe_unused cyttsp_suspend(struct device *dev)
 {
 	struct cyttsp *ts = dev_get_drvdata(dev);
 	int retval = 0;
@@ -491,7 +490,7 @@
 	return retval;
 }
 
-static int cyttsp_resume(struct device *dev)
+static int __maybe_unused cyttsp_resume(struct device *dev)
 {
 	struct cyttsp *ts = dev_get_drvdata(dev);
 
@@ -507,8 +506,6 @@
 	return 0;
 }
 
-#endif
-
 SIMPLE_DEV_PM_OPS(cyttsp_pm_ops, cyttsp_suspend, cyttsp_resume);
 EXPORT_SYMBOL_GPL(cyttsp_pm_ops);
 
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index ee3434f..3793fcc 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -1092,8 +1092,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int edt_ft5x06_ts_suspend(struct device *dev)
+static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
@@ -1103,7 +1102,7 @@
 	return 0;
 }
 
-static int edt_ft5x06_ts_resume(struct device *dev)
+static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
@@ -1112,7 +1111,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(edt_ft5x06_ts_pm_ops,
 			 edt_ft5x06_ts_suspend, edt_ft5x06_ts_resume);
diff --git a/drivers/input/touchscreen/eeti_ts.c b/drivers/input/touchscreen/eeti_ts.c
index b1884dd..09be6ce 100644
--- a/drivers/input/touchscreen/eeti_ts.c
+++ b/drivers/input/touchscreen/eeti_ts.c
@@ -264,8 +264,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int eeti_ts_suspend(struct device *dev)
+static int __maybe_unused eeti_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct eeti_ts_priv *priv = i2c_get_clientdata(client);
@@ -284,7 +283,7 @@
 	return 0;
 }
 
-static int eeti_ts_resume(struct device *dev)
+static int __maybe_unused eeti_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct eeti_ts_priv *priv = i2c_get_clientdata(client);
@@ -302,7 +301,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(eeti_ts_pm, eeti_ts_suspend, eeti_ts_resume);
 
diff --git a/drivers/input/touchscreen/egalax_ts.c b/drivers/input/touchscreen/egalax_ts.c
index c805784..4c56299 100644
--- a/drivers/input/touchscreen/egalax_ts.c
+++ b/drivers/input/touchscreen/egalax_ts.c
@@ -239,8 +239,7 @@
 };
 MODULE_DEVICE_TABLE(i2c, egalax_ts_id);
 
-#ifdef CONFIG_PM_SLEEP
-static int egalax_ts_suspend(struct device *dev)
+static int __maybe_unused egalax_ts_suspend(struct device *dev)
 {
 	static const u8 suspend_cmd[MAX_I2C_DATA_LEN] = {
 		0x3, 0x6, 0xa, 0x3, 0x36, 0x3f, 0x2, 0, 0, 0
@@ -252,13 +251,12 @@
 	return ret > 0 ? 0 : ret;
 }
 
-static int egalax_ts_resume(struct device *dev)
+static int __maybe_unused egalax_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
 	return egalax_wake_up_device(client);
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(egalax_ts_pm_ops, egalax_ts_suspend, egalax_ts_resume);
 
diff --git a/drivers/input/touchscreen/elants_i2c.c b/drivers/input/touchscreen/elants_i2c.c
new file mode 100644
index 0000000..a510f7e
--- /dev/null
+++ b/drivers/input/touchscreen/elants_i2c.c
@@ -0,0 +1,1271 @@
+/*
+ * Elan Microelectronics touch panels with I2C interface
+ *
+ * Copyright (C) 2014 Elan Microelectronics Corporation.
+ * Scott Liu <scott.liu@emc.com.tw>
+ *
+ * This code is partly based on hid-multitouch.c:
+ *
+ *  Copyright (c) 2010-2012 Stephane Chatty <chatty@enac.fr>
+ *  Copyright (c) 2010-2012 Benjamin Tissoires <benjamin.tissoires@gmail.com>
+ *  Copyright (c) 2010-2012 Ecole Nationale de l'Aviation Civile, France
+ *
+ *
+ * This code is partly based on i2c-hid.c:
+ *
+ * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com>
+ * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
+ * Copyright (c) 2012 Red Hat, Inc
+ */
+
+/*
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ */
+
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/async.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/uaccess.h>
+#include <linux/buffer_head.h>
+#include <linux/version.h>
+#include <linux/slab.h>
+#include <linux/firmware.h>
+#include <linux/version.h>
+#include <linux/input/mt.h>
+#include <linux/acpi.h>
+#include <linux/of.h>
+#include <asm/unaligned.h>
+
+/* Device, Driver information */
+#define DEVICE_NAME	"elants_i2c"
+#define DRV_VERSION	"1.0.9"
+
+/* Convert from rows or columns into resolution */
+#define ELAN_TS_RESOLUTION(n, m)   (((n) - 1) * (m))
+
+/* FW header data */
+#define HEADER_SIZE		4
+#define FW_HDR_TYPE		0
+#define FW_HDR_COUNT		1
+#define FW_HDR_LENGTH		2
+
+/* Buffer mode Queue Header information */
+#define QUEUE_HEADER_SINGLE	0x62
+#define QUEUE_HEADER_NORMAL	0X63
+#define QUEUE_HEADER_WAIT	0x64
+
+/* Command header definition */
+#define CMD_HEADER_WRITE	0x54
+#define CMD_HEADER_READ		0x53
+#define CMD_HEADER_6B_READ	0x5B
+#define CMD_HEADER_RESP		0x52
+#define CMD_HEADER_6B_RESP	0x9B
+#define CMD_HEADER_HELLO	0x55
+#define CMD_HEADER_REK		0x66
+
+/* FW position data */
+#define PACKET_SIZE		55
+#define MAX_CONTACT_NUM		10
+#define FW_POS_HEADER		0
+#define FW_POS_STATE		1
+#define FW_POS_TOTAL		2
+#define FW_POS_XY		3
+#define FW_POS_CHECKSUM		34
+#define FW_POS_WIDTH		35
+#define FW_POS_PRESSURE		45
+
+#define HEADER_REPORT_10_FINGER	0x62
+
+/* Header (4 bytes) plus 3 fill 10-finger packets */
+#define MAX_PACKET_SIZE		169
+
+#define BOOT_TIME_DELAY_MS	50
+
+/* FW read command, 0x53 0x?? 0x0, 0x01 */
+#define E_ELAN_INFO_FW_VER	0x00
+#define E_ELAN_INFO_BC_VER	0x10
+#define E_ELAN_INFO_TEST_VER	0xE0
+#define E_ELAN_INFO_FW_ID	0xF0
+#define E_INFO_OSR		0xD6
+#define E_INFO_PHY_SCAN		0xD7
+#define E_INFO_PHY_DRIVER	0xD8
+
+#define MAX_RETRIES		3
+#define MAX_FW_UPDATE_RETRIES	30
+
+#define ELAN_FW_PAGESIZE	132
+#define ELAN_FW_FILENAME	"elants_i2c.bin"
+
+/* calibration timeout definition */
+#define ELAN_CALI_TIMEOUT_MSEC	10000
+
+enum elants_state {
+	ELAN_STATE_NORMAL,
+	ELAN_WAIT_QUEUE_HEADER,
+	ELAN_WAIT_RECALIBRATION,
+};
+
+enum elants_iap_mode {
+	ELAN_IAP_OPERATIONAL,
+	ELAN_IAP_RECOVERY,
+};
+
+/* struct elants_data - represents state of Elan touchscreen device */
+struct elants_data {
+	struct i2c_client *client;
+	struct input_dev *input;
+
+	u16 fw_version;
+	u8 test_version;
+	u8 solution_version;
+	u8 bc_version;
+	u8 iap_version;
+	u16 hw_version;
+	unsigned int x_res;	/* resolution in units/mm */
+	unsigned int y_res;
+	unsigned int x_max;
+	unsigned int y_max;
+
+	enum elants_state state;
+	enum elants_iap_mode iap_mode;
+
+	/* Guards against concurrent access to the device via sysfs */
+	struct mutex sysfs_mutex;
+
+	u8 cmd_resp[HEADER_SIZE];
+	struct completion cmd_done;
+
+	u8 buf[MAX_PACKET_SIZE];
+
+	bool wake_irq_enabled;
+};
+
+static int elants_i2c_send(struct i2c_client *client,
+			   const void *data, size_t size)
+{
+	int ret;
+
+	ret = i2c_master_send(client, data, size);
+	if (ret == size)
+		return 0;
+
+	if (ret >= 0)
+		ret = -EIO;
+
+	dev_err(&client->dev, "%s failed (%*ph): %d\n",
+		__func__, (int)size, data, ret);
+
+	return ret;
+}
+
+static int elants_i2c_read(struct i2c_client *client, void *data, size_t size)
+{
+	int ret;
+
+	ret = i2c_master_recv(client, data, size);
+	if (ret == size)
+		return 0;
+
+	if (ret >= 0)
+		ret = -EIO;
+
+	dev_err(&client->dev, "%s failed: %d\n", __func__, ret);
+
+	return ret;
+}
+
+static int elants_i2c_execute_command(struct i2c_client *client,
+				      const u8 *cmd, size_t cmd_size,
+				      u8 *resp, size_t resp_size)
+{
+	struct i2c_msg msgs[2];
+	int ret;
+	u8 expected_response;
+
+	switch (cmd[0]) {
+	case CMD_HEADER_READ:
+		expected_response = CMD_HEADER_RESP;
+		break;
+
+	case CMD_HEADER_6B_READ:
+		expected_response = CMD_HEADER_6B_RESP;
+		break;
+
+	default:
+		dev_err(&client->dev, "%s: invalid command %*ph\n",
+			__func__, (int)cmd_size, cmd);
+		return -EINVAL;
+	}
+
+	msgs[0].addr = client->addr;
+	msgs[0].flags = client->flags & I2C_M_TEN;
+	msgs[0].len = cmd_size;
+	msgs[0].buf = (u8 *)cmd;
+
+	msgs[1].addr = client->addr;
+	msgs[1].flags = client->flags & I2C_M_TEN;
+	msgs[1].flags |= I2C_M_RD;
+	msgs[1].len = resp_size;
+	msgs[1].buf = resp;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret < 0)
+		return ret;
+
+	if (ret != ARRAY_SIZE(msgs) || resp[FW_HDR_TYPE] != expected_response)
+		return -EIO;
+
+	return 0;
+}
+
+static int elants_i2c_calibrate(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int ret, error;
+	static const u8 w_flashkey[] = { 0x54, 0xC0, 0xE1, 0x5A };
+	static const u8 rek[] = { 0x54, 0x29, 0x00, 0x01 };
+	static const u8 rek_resp[] = { CMD_HEADER_REK, 0x66, 0x66, 0x66 };
+
+	disable_irq(client->irq);
+
+	ts->state = ELAN_WAIT_RECALIBRATION;
+	reinit_completion(&ts->cmd_done);
+
+	elants_i2c_send(client, w_flashkey, sizeof(w_flashkey));
+	elants_i2c_send(client, rek, sizeof(rek));
+
+	enable_irq(client->irq);
+
+	ret = wait_for_completion_interruptible_timeout(&ts->cmd_done,
+				msecs_to_jiffies(ELAN_CALI_TIMEOUT_MSEC));
+
+	ts->state = ELAN_STATE_NORMAL;
+
+	if (ret <= 0) {
+		error = ret < 0 ? ret : -ETIMEDOUT;
+		dev_err(&client->dev,
+			"error while waiting for calibration to complete: %d\n",
+			error);
+		return error;
+	}
+
+	if (memcmp(rek_resp, ts->cmd_resp, sizeof(rek_resp))) {
+		dev_err(&client->dev,
+			"unexpected calibration response: %*ph\n",
+			(int)sizeof(ts->cmd_resp), ts->cmd_resp);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int elants_i2c_sw_reset(struct i2c_client *client)
+{
+	const u8 soft_rst_cmd[] = { 0x77, 0x77, 0x77, 0x77 };
+	int error;
+
+	error = elants_i2c_send(client, soft_rst_cmd,
+				sizeof(soft_rst_cmd));
+	if (error) {
+		dev_err(&client->dev, "software reset failed: %d\n", error);
+		return error;
+	}
+
+	/*
+	 * We should wait at least 10 msec (but no more than 40) before
+	 * sending fastboot or IAP command to the device.
+	 */
+	msleep(30);
+
+	return 0;
+}
+
+static u16 elants_i2c_parse_version(u8 *buf)
+{
+	return get_unaligned_be32(buf) >> 4;
+}
+
+static int elants_i2c_query_fw_id(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int error, retry_cnt;
+	const u8 cmd[] = { CMD_HEADER_READ, E_ELAN_INFO_FW_ID, 0x00, 0x01 };
+	u8 resp[HEADER_SIZE];
+
+	for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
+		error = elants_i2c_execute_command(client, cmd, sizeof(cmd),
+						   resp, sizeof(resp));
+		if (!error) {
+			ts->hw_version = elants_i2c_parse_version(resp);
+			if (ts->hw_version != 0xffff)
+				return 0;
+		}
+
+		dev_dbg(&client->dev, "read fw id error=%d, buf=%*phC\n",
+			error, (int)sizeof(resp), resp);
+	}
+
+	dev_err(&client->dev,
+		"Failed to read fw id or fw id is invalid\n");
+
+	return -EINVAL;
+}
+
+static int elants_i2c_query_fw_version(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int error, retry_cnt;
+	const u8 cmd[] = { CMD_HEADER_READ, E_ELAN_INFO_FW_VER, 0x00, 0x01 };
+	u8 resp[HEADER_SIZE];
+
+	for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
+		error = elants_i2c_execute_command(client, cmd, sizeof(cmd),
+						   resp, sizeof(resp));
+		if (!error) {
+			ts->fw_version = elants_i2c_parse_version(resp);
+			if (ts->fw_version != 0x0000 &&
+			    ts->fw_version != 0xffff)
+				return 0;
+		}
+
+		dev_dbg(&client->dev, "read fw version error=%d, buf=%*phC\n",
+			error, (int)sizeof(resp), resp);
+	}
+
+	dev_err(&client->dev,
+		"Failed to read fw version or fw version is invalid\n");
+
+	return -EINVAL;
+}
+
+static int elants_i2c_query_test_version(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int error, retry_cnt;
+	u16 version;
+	const u8 cmd[] = { CMD_HEADER_READ, E_ELAN_INFO_TEST_VER, 0x00, 0x01 };
+	u8 resp[HEADER_SIZE];
+
+	for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
+		error = elants_i2c_execute_command(client, cmd, sizeof(cmd),
+						   resp, sizeof(resp));
+		if (!error) {
+			version = elants_i2c_parse_version(resp);
+			ts->test_version = version >> 8;
+			ts->solution_version = version & 0xff;
+
+			return 0;
+		}
+
+		dev_dbg(&client->dev,
+			"read test version error rc=%d, buf=%*phC\n",
+			error, (int)sizeof(resp), resp);
+	}
+
+	dev_err(&client->dev, "Failed to read test version\n");
+
+	return -EINVAL;
+}
+
+static int elants_i2c_query_bc_version(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	const u8 cmd[] = { CMD_HEADER_READ, E_ELAN_INFO_BC_VER, 0x00, 0x01 };
+	u8 resp[HEADER_SIZE];
+	u16 version;
+	int error;
+
+	error = elants_i2c_execute_command(client, cmd, sizeof(cmd),
+					   resp, sizeof(resp));
+	if (error) {
+		dev_err(&client->dev,
+			"read BC version error=%d, buf=%*phC\n",
+			error, (int)sizeof(resp), resp);
+		return error;
+	}
+
+	version = elants_i2c_parse_version(resp);
+	ts->bc_version = version >> 8;
+	ts->iap_version = version & 0xff;
+
+	return 0;
+}
+
+static int elants_i2c_query_ts_info(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int error;
+	u8 resp[17];
+	u16 phy_x, phy_y, rows, cols, osr;
+	const u8 get_resolution_cmd[] = {
+		CMD_HEADER_6B_READ, 0x00, 0x00, 0x00, 0x00, 0x00
+	};
+	const u8 get_osr_cmd[] = {
+		CMD_HEADER_READ, E_INFO_OSR, 0x00, 0x01
+	};
+	const u8 get_physical_scan_cmd[] = {
+		CMD_HEADER_READ, E_INFO_PHY_SCAN, 0x00, 0x01
+	};
+	const u8 get_physical_drive_cmd[] = {
+		CMD_HEADER_READ, E_INFO_PHY_DRIVER, 0x00, 0x01
+	};
+
+	/* Get trace number */
+	error = elants_i2c_execute_command(client,
+					   get_resolution_cmd,
+					   sizeof(get_resolution_cmd),
+					   resp, sizeof(resp));
+	if (error) {
+		dev_err(&client->dev, "get resolution command failed: %d\n",
+			error);
+		return error;
+	}
+
+	rows = resp[2] + resp[6] + resp[10];
+	cols = resp[3] + resp[7] + resp[11];
+
+	/* Process mm_to_pixel information */
+	error = elants_i2c_execute_command(client,
+					   get_osr_cmd, sizeof(get_osr_cmd),
+					   resp, sizeof(resp));
+	if (error) {
+		dev_err(&client->dev, "get osr command failed: %d\n",
+			error);
+		return error;
+	}
+
+	osr = resp[3];
+
+	error = elants_i2c_execute_command(client,
+					   get_physical_scan_cmd,
+					   sizeof(get_physical_scan_cmd),
+					   resp, sizeof(resp));
+	if (error) {
+		dev_err(&client->dev, "get physical scan command failed: %d\n",
+			error);
+		return error;
+	}
+
+	phy_x = get_unaligned_be16(&resp[2]);
+
+	error = elants_i2c_execute_command(client,
+					   get_physical_drive_cmd,
+					   sizeof(get_physical_drive_cmd),
+					   resp, sizeof(resp));
+	if (error) {
+		dev_err(&client->dev, "get physical drive command failed: %d\n",
+			error);
+		return error;
+	}
+
+	phy_y = get_unaligned_be16(&resp[2]);
+
+	dev_dbg(&client->dev, "phy_x=%d, phy_y=%d\n", phy_x, phy_y);
+
+	if (rows == 0 || cols == 0 || osr == 0) {
+		dev_warn(&client->dev,
+			 "invalid trace number data: %d, %d, %d\n",
+			 rows, cols, osr);
+	} else {
+		/* translate trace number to TS resolution */
+		ts->x_max = ELAN_TS_RESOLUTION(rows, osr);
+		ts->x_res = DIV_ROUND_CLOSEST(ts->x_max, phy_x);
+		ts->y_max = ELAN_TS_RESOLUTION(cols, osr);
+		ts->y_res = DIV_ROUND_CLOSEST(ts->y_max, phy_y);
+	}
+
+	return 0;
+}
+
+static int elants_i2c_fastboot(struct i2c_client *client)
+{
+	const u8 boot_cmd[] = { 0x4D, 0x61, 0x69, 0x6E };
+	int error;
+
+	error = elants_i2c_send(client, boot_cmd, sizeof(boot_cmd));
+	if (error) {
+		dev_err(&client->dev, "boot failed: %d\n", error);
+		return error;
+	}
+
+	dev_dbg(&client->dev, "boot success -- 0x%x\n", client->addr);
+	return 0;
+}
+
+static int elants_i2c_initialize(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int error, retry_cnt;
+	const u8 hello_packet[] = { 0x55, 0x55, 0x55, 0x55 };
+	const u8 recov_packet[] = { 0x55, 0x55, 0x80, 0x80 };
+	u8 buf[HEADER_SIZE];
+
+	for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
+		error = elants_i2c_sw_reset(client);
+		if (error) {
+			/* Continue initializing if it's the last try */
+			if (retry_cnt < MAX_RETRIES - 1)
+				continue;
+		}
+
+		error = elants_i2c_fastboot(client);
+		if (error) {
+			/* Continue initializing if it's the last try */
+			if (retry_cnt < MAX_RETRIES - 1)
+				continue;
+		}
+
+		/* Wait for Hello packet */
+		msleep(BOOT_TIME_DELAY_MS);
+
+		error = elants_i2c_read(client, buf, sizeof(buf));
+		if (error) {
+			dev_err(&client->dev,
+				"failed to read 'hello' packet: %d\n", error);
+		} else if (!memcmp(buf, hello_packet, sizeof(hello_packet))) {
+			ts->iap_mode = ELAN_IAP_OPERATIONAL;
+			break;
+		} else if (!memcmp(buf, recov_packet, sizeof(recov_packet))) {
+			/*
+			 * Setting error code will mark device
+			 * in recovery mode below.
+			 */
+			error = -EIO;
+			break;
+		} else {
+			error = -EINVAL;
+			dev_err(&client->dev,
+				"invalid 'hello' packet: %*ph\n",
+				(int)sizeof(buf), buf);
+		}
+	}
+
+	if (!error)
+		error = elants_i2c_query_fw_id(ts);
+	if (!error)
+		error = elants_i2c_query_fw_version(ts);
+
+	if (error) {
+		ts->iap_mode = ELAN_IAP_RECOVERY;
+	} else {
+		elants_i2c_query_test_version(ts);
+		elants_i2c_query_bc_version(ts);
+		elants_i2c_query_ts_info(ts);
+	}
+
+	return 0;
+}
+
+/*
+ * Firmware update interface.
+ */
+
+static int elants_i2c_fw_write_page(struct i2c_client *client,
+				    const void *page)
+{
+	const u8 ack_ok[] = { 0xaa, 0xaa };
+	u8 buf[2];
+	int retry;
+	int error;
+
+	for (retry = 0; retry < MAX_FW_UPDATE_RETRIES; retry++) {
+		error = elants_i2c_send(client, page, ELAN_FW_PAGESIZE);
+		if (error) {
+			dev_err(&client->dev,
+				"IAP Write Page failed: %d\n", error);
+			continue;
+		}
+
+		error = elants_i2c_read(client, buf, 2);
+		if (error) {
+			dev_err(&client->dev,
+				"IAP Ack read failed: %d\n", error);
+			return error;
+		}
+
+		if (!memcmp(buf, ack_ok, sizeof(ack_ok)))
+			return 0;
+
+		error = -EIO;
+		dev_err(&client->dev,
+			"IAP Get Ack Error [%02x:%02x]\n",
+			buf[0], buf[1]);
+	}
+
+	return error;
+}
+
+static int elants_i2c_do_update_firmware(struct i2c_client *client,
+					 const struct firmware *fw,
+					 bool force)
+{
+	const u8 enter_iap[] = { 0x45, 0x49, 0x41, 0x50 };
+	const u8 enter_iap2[] = { 0x54, 0x00, 0x12, 0x34 };
+	const u8 iap_ack[] = { 0x55, 0xaa, 0x33, 0xcc };
+	u8 buf[HEADER_SIZE];
+	u16 send_id;
+	int page, n_fw_pages;
+	int error;
+
+	/* Recovery mode detection! */
+	if (force) {
+		dev_dbg(&client->dev, "Recovery mode procedure\n");
+		error = elants_i2c_send(client, enter_iap2, sizeof(enter_iap2));
+	} else {
+		/* Start IAP Procedure */
+		dev_dbg(&client->dev, "Normal IAP procedure\n");
+		elants_i2c_sw_reset(client);
+
+		error = elants_i2c_send(client, enter_iap, sizeof(enter_iap));
+	}
+
+	if (error) {
+		dev_err(&client->dev, "failed to enter IAP mode: %d\n", error);
+		return error;
+	}
+
+	msleep(20);
+
+	/* check IAP state */
+	error = elants_i2c_read(client, buf, 4);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to read IAP acknowledgement: %d\n",
+			error);
+		return error;
+	}
+
+	if (memcmp(buf, iap_ack, sizeof(iap_ack))) {
+		dev_err(&client->dev,
+			"failed to enter IAP: %*ph (expected %*ph)\n",
+			(int)sizeof(buf), buf, (int)sizeof(iap_ack), iap_ack);
+		return -EIO;
+	}
+
+	dev_info(&client->dev, "successfully entered IAP mode");
+
+	send_id = client->addr;
+	error = elants_i2c_send(client, &send_id, 1);
+	if (error) {
+		dev_err(&client->dev, "sending dummy byte failed: %d\n",
+			error);
+		return error;
+	}
+
+	/* Clear the last page of Master */
+	error = elants_i2c_send(client, fw->data, ELAN_FW_PAGESIZE);
+	if (error) {
+		dev_err(&client->dev, "clearing of the last page failed: %d\n",
+			error);
+		return error;
+	}
+
+	error = elants_i2c_read(client, buf, 2);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to read ACK for clearing the last page: %d\n",
+			error);
+		return error;
+	}
+
+	n_fw_pages = fw->size / ELAN_FW_PAGESIZE;
+	dev_dbg(&client->dev, "IAP Pages = %d\n", n_fw_pages);
+
+	for (page = 0; page < n_fw_pages; page++) {
+		error = elants_i2c_fw_write_page(client,
+					fw->data + page * ELAN_FW_PAGESIZE);
+		if (error) {
+			dev_err(&client->dev,
+				"failed to write FW page %d: %d\n",
+				page, error);
+			return error;
+		}
+	}
+
+	/* Old iap needs to wait 200ms for WDT and rest is for hello packets */
+	msleep(300);
+
+	dev_info(&client->dev, "firmware update completed\n");
+	return 0;
+}
+
+static int elants_i2c_fw_update(struct elants_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	const struct firmware *fw;
+	int error;
+
+	error = request_firmware(&fw, ELAN_FW_FILENAME, &client->dev);
+	if (error) {
+		dev_err(&client->dev, "failed to request firmware %s: %d\n",
+			ELAN_FW_FILENAME, error);
+		return error;
+	}
+
+	if (fw->size % ELAN_FW_PAGESIZE) {
+		dev_err(&client->dev, "invalid firmware length: %zu\n",
+			fw->size);
+		error = -EINVAL;
+		goto out;
+	}
+
+	disable_irq(client->irq);
+
+	error = elants_i2c_do_update_firmware(client, fw,
+					ts->iap_mode == ELAN_IAP_RECOVERY);
+	if (error) {
+		dev_err(&client->dev, "firmware update failed: %d\n", error);
+		ts->iap_mode = ELAN_IAP_RECOVERY;
+		goto out_enable_irq;
+	}
+
+	error = elants_i2c_initialize(ts);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to initialize device after firmware update: %d\n",
+			error);
+		ts->iap_mode = ELAN_IAP_RECOVERY;
+		goto out_enable_irq;
+	}
+
+	ts->iap_mode = ELAN_IAP_OPERATIONAL;
+
+out_enable_irq:
+	ts->state = ELAN_STATE_NORMAL;
+	enable_irq(client->irq);
+	msleep(100);
+
+	if (!error)
+		elants_i2c_calibrate(ts);
+out:
+	release_firmware(fw);
+	return error;
+}
+
+/*
+ * Event reporting.
+ */
+
+static void elants_i2c_mt_event(struct elants_data *ts, u8 *buf)
+{
+	struct input_dev *input = ts->input;
+	unsigned int n_fingers;
+	u16 finger_state;
+	int i;
+
+	n_fingers = buf[FW_POS_STATE + 1] & 0x0f;
+	finger_state = ((buf[FW_POS_STATE + 1] & 0x30) << 4) |
+			buf[FW_POS_STATE];
+
+	dev_dbg(&ts->client->dev,
+		"n_fingers: %u, state: %04x\n",  n_fingers, finger_state);
+
+	for (i = 0; i < MAX_CONTACT_NUM && n_fingers; i++) {
+		if (finger_state & 1) {
+			unsigned int x, y, p, w;
+			u8 *pos;
+
+			pos = &buf[FW_POS_XY + i * 3];
+			x = (((u16)pos[0] & 0xf0) << 4) | pos[1];
+			y = (((u16)pos[0] & 0x0f) << 8) | pos[2];
+			p = buf[FW_POS_PRESSURE + i];
+			w = buf[FW_POS_WIDTH + i];
+
+			dev_dbg(&ts->client->dev, "i=%d x=%d y=%d p=%d w=%d\n",
+				i, x, y, p, w);
+
+			input_mt_slot(input, i);
+			input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+			input_event(input, EV_ABS, ABS_MT_POSITION_X, x);
+			input_event(input, EV_ABS, ABS_MT_POSITION_Y, y);
+			input_event(input, EV_ABS, ABS_MT_PRESSURE, p);
+			input_event(input, EV_ABS, ABS_MT_TOUCH_MAJOR, w);
+
+			n_fingers--;
+		}
+
+		finger_state >>= 1;
+	}
+
+	input_mt_sync_frame(input);
+	input_sync(input);
+}
+
+static u8 elants_i2c_calculate_checksum(u8 *buf)
+{
+	u8 checksum = 0;
+	u8 i;
+
+	for (i = 0; i < FW_POS_CHECKSUM; i++)
+		checksum += buf[i];
+
+	return checksum;
+}
+
+static void elants_i2c_event(struct elants_data *ts, u8 *buf)
+{
+	u8 checksum = elants_i2c_calculate_checksum(buf);
+
+	if (unlikely(buf[FW_POS_CHECKSUM] != checksum))
+		dev_warn(&ts->client->dev,
+			 "%s: invalid checksum for packet %02x: %02x vs. %02x\n",
+			 __func__, buf[FW_POS_HEADER],
+			 checksum, buf[FW_POS_CHECKSUM]);
+	else if (unlikely(buf[FW_POS_HEADER] != HEADER_REPORT_10_FINGER))
+		dev_warn(&ts->client->dev,
+			 "%s: unknown packet type: %02x\n",
+			 __func__, buf[FW_POS_HEADER]);
+	else
+		elants_i2c_mt_event(ts, buf);
+}
+
+static irqreturn_t elants_i2c_irq(int irq, void *_dev)
+{
+	const u8 wait_packet[] = { 0x64, 0x64, 0x64, 0x64 };
+	struct elants_data *ts = _dev;
+	struct i2c_client *client = ts->client;
+	int report_count, report_len;
+	int i;
+	int len;
+
+	len = i2c_master_recv(client, ts->buf, sizeof(ts->buf));
+	if (len < 0) {
+		dev_err(&client->dev, "%s: failed to read data: %d\n",
+			__func__, len);
+		goto out;
+	}
+
+	dev_dbg(&client->dev, "%s: packet %*ph\n",
+		__func__, HEADER_SIZE, ts->buf);
+
+	switch (ts->state) {
+	case ELAN_WAIT_RECALIBRATION:
+		if (ts->buf[FW_HDR_TYPE] == CMD_HEADER_REK) {
+			memcpy(ts->cmd_resp, ts->buf, sizeof(ts->cmd_resp));
+			complete(&ts->cmd_done);
+			ts->state = ELAN_STATE_NORMAL;
+		}
+		break;
+
+	case ELAN_WAIT_QUEUE_HEADER:
+		if (ts->buf[FW_HDR_TYPE] != QUEUE_HEADER_NORMAL)
+			break;
+
+		ts->state = ELAN_STATE_NORMAL;
+		/* fall through */
+
+	case ELAN_STATE_NORMAL:
+
+		switch (ts->buf[FW_HDR_TYPE]) {
+		case CMD_HEADER_HELLO:
+		case CMD_HEADER_RESP:
+		case CMD_HEADER_REK:
+			break;
+
+		case QUEUE_HEADER_WAIT:
+			if (memcmp(ts->buf, wait_packet, sizeof(wait_packet))) {
+				dev_err(&client->dev,
+					"invalid wait packet %*ph\n",
+					HEADER_SIZE, ts->buf);
+			} else {
+				ts->state = ELAN_WAIT_QUEUE_HEADER;
+				udelay(30);
+			}
+			break;
+
+		case QUEUE_HEADER_SINGLE:
+			elants_i2c_event(ts, &ts->buf[HEADER_SIZE]);
+			break;
+
+		case QUEUE_HEADER_NORMAL:
+			report_count = ts->buf[FW_HDR_COUNT];
+			if (report_count > 3) {
+				dev_err(&client->dev,
+					"too large report count: %*ph\n",
+					HEADER_SIZE, ts->buf);
+				break;
+			}
+
+			report_len = ts->buf[FW_HDR_LENGTH] / report_count;
+			if (report_len != PACKET_SIZE) {
+				dev_err(&client->dev,
+					"mismatching report length: %*ph\n",
+					HEADER_SIZE, ts->buf);
+				break;
+			}
+
+			for (i = 0; i < report_count; i++) {
+				u8 *buf = ts->buf + HEADER_SIZE +
+							i * PACKET_SIZE;
+				elants_i2c_event(ts, buf);
+			}
+			break;
+
+		default:
+			dev_err(&client->dev, "unknown packet %*ph\n",
+				HEADER_SIZE, ts->buf);
+			break;
+		}
+		break;
+	}
+
+out:
+	return IRQ_HANDLED;
+}
+
+/*
+ * sysfs interface
+ */
+static ssize_t calibrate_store(struct device *dev,
+			       struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elants_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	error = mutex_lock_interruptible(&ts->sysfs_mutex);
+	if (error)
+		return error;
+
+	error = elants_i2c_calibrate(ts);
+
+	mutex_unlock(&ts->sysfs_mutex);
+	return error ?: count;
+}
+
+static ssize_t write_update_fw(struct device *dev,
+			       struct device_attribute *attr,
+			       const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elants_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	error = mutex_lock_interruptible(&ts->sysfs_mutex);
+	if (error)
+		return error;
+
+	error = elants_i2c_fw_update(ts);
+	dev_dbg(dev, "firmware update result: %d\n", error);
+
+	mutex_unlock(&ts->sysfs_mutex);
+	return error ?: count;
+}
+
+static ssize_t show_iap_mode(struct device *dev,
+			     struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elants_data *ts = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%s\n",
+		       ts->iap_mode == ELAN_IAP_OPERATIONAL ?
+				"Normal" : "Recovery");
+}
+
+static DEVICE_ATTR(calibrate, S_IWUSR, NULL, calibrate_store);
+static DEVICE_ATTR(iap_mode, S_IRUGO, show_iap_mode, NULL);
+static DEVICE_ATTR(update_fw, S_IWUSR, NULL, write_update_fw);
+
+struct elants_version_attribute {
+	struct device_attribute dattr;
+	size_t field_offset;
+	size_t field_size;
+};
+
+#define __ELANTS_FIELD_SIZE(_field)					\
+	sizeof(((struct elants_data *)NULL)->_field)
+#define __ELANTS_VERIFY_SIZE(_field)					\
+	(BUILD_BUG_ON_ZERO(__ELANTS_FIELD_SIZE(_field) > 2) +		\
+	 __ELANTS_FIELD_SIZE(_field))
+#define ELANTS_VERSION_ATTR(_field)					\
+	struct elants_version_attribute elants_ver_attr_##_field = {	\
+		.dattr = __ATTR(_field, S_IRUGO,			\
+				elants_version_attribute_show, NULL),	\
+		.field_offset = offsetof(struct elants_data, _field),	\
+		.field_size = __ELANTS_VERIFY_SIZE(_field),		\
+	}
+
+static ssize_t elants_version_attribute_show(struct device *dev,
+					     struct device_attribute *dattr,
+					     char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elants_data *ts = i2c_get_clientdata(client);
+	struct elants_version_attribute *attr =
+		container_of(dattr, struct elants_version_attribute, dattr);
+	u8 *field = (u8 *)((char *)ts + attr->field_offset);
+	unsigned int fmt_size;
+	unsigned int val;
+
+	if (attr->field_size == 1) {
+		val = *field;
+		fmt_size = 2; /* 2 HEX digits */
+	} else {
+		val = *(u16 *)field;
+		fmt_size = 4; /* 4 HEX digits */
+	}
+
+	return sprintf(buf, "%0*x\n", fmt_size, val);
+}
+
+static ELANTS_VERSION_ATTR(fw_version);
+static ELANTS_VERSION_ATTR(hw_version);
+static ELANTS_VERSION_ATTR(test_version);
+static ELANTS_VERSION_ATTR(solution_version);
+static ELANTS_VERSION_ATTR(bc_version);
+static ELANTS_VERSION_ATTR(iap_version);
+
+static struct attribute *elants_attributes[] = {
+	&dev_attr_calibrate.attr,
+	&dev_attr_update_fw.attr,
+	&dev_attr_iap_mode.attr,
+
+	&elants_ver_attr_fw_version.dattr.attr,
+	&elants_ver_attr_hw_version.dattr.attr,
+	&elants_ver_attr_test_version.dattr.attr,
+	&elants_ver_attr_solution_version.dattr.attr,
+	&elants_ver_attr_bc_version.dattr.attr,
+	&elants_ver_attr_iap_version.dattr.attr,
+	NULL
+};
+
+static struct attribute_group elants_attribute_group = {
+	.attrs = elants_attributes,
+};
+
+static void elants_i2c_remove_sysfs_group(void *_data)
+{
+	struct elants_data *ts = _data;
+
+	sysfs_remove_group(&ts->client->dev.kobj, &elants_attribute_group);
+}
+
+static int elants_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	union i2c_smbus_data dummy;
+	struct elants_data *ts;
+	unsigned long irqflags;
+	int error;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev,
+			"%s: i2c check functionality error\n", DEVICE_NAME);
+		return -ENXIO;
+	}
+
+	/* Make sure there is something at this address */
+	if (i2c_smbus_xfer(client->adapter, client->addr, 0,
+			I2C_SMBUS_READ, 0, I2C_SMBUS_BYTE, &dummy) < 0) {
+		dev_err(&client->dev, "nothing at this address\n");
+		return -ENXIO;
+	}
+
+	ts = devm_kzalloc(&client->dev, sizeof(struct elants_data), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	mutex_init(&ts->sysfs_mutex);
+	init_completion(&ts->cmd_done);
+
+	ts->client = client;
+	i2c_set_clientdata(client, ts);
+
+	error = elants_i2c_initialize(ts);
+	if (error) {
+		dev_err(&client->dev, "failed to initialize: %d\n", error);
+		return error;
+	}
+
+	ts->input = devm_input_allocate_device(&client->dev);
+	if (!ts->input) {
+		dev_err(&client->dev, "Failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	ts->input->name = "Elan Touchscreen";
+	ts->input->id.bustype = BUS_I2C;
+
+	__set_bit(BTN_TOUCH, ts->input->keybit);
+	__set_bit(EV_ABS, ts->input->evbit);
+	__set_bit(EV_KEY, ts->input->evbit);
+
+	/* Single touch input params setup */
+	input_set_abs_params(ts->input, ABS_X, 0, ts->x_max, 0, 0);
+	input_set_abs_params(ts->input, ABS_Y, 0, ts->y_max, 0, 0);
+	input_set_abs_params(ts->input, ABS_PRESSURE, 0, 255, 0, 0);
+	input_abs_set_res(ts->input, ABS_X, ts->x_res);
+	input_abs_set_res(ts->input, ABS_Y, ts->y_res);
+
+	/* Multitouch input params setup */
+	error = input_mt_init_slots(ts->input, MAX_CONTACT_NUM,
+				    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to initialize MT slots: %d\n", error);
+		return error;
+	}
+
+	input_set_abs_params(ts->input, ABS_MT_POSITION_X, 0, ts->x_max, 0, 0);
+	input_set_abs_params(ts->input, ABS_MT_POSITION_Y, 0, ts->y_max, 0, 0);
+	input_set_abs_params(ts->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
+	input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
+	input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->x_res);
+	input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->y_res);
+
+	input_set_drvdata(ts->input, ts);
+
+	error = input_register_device(ts->input);
+	if (error) {
+		dev_err(&client->dev,
+			"unable to register input device: %d\n", error);
+		return error;
+	}
+
+	/*
+	 * Systems using device tree should set up interrupt via DTS,
+	 * the rest will use the default falling edge interrupts.
+	 */
+	irqflags = client->dev.of_node ? 0 : IRQF_TRIGGER_FALLING;
+
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, elants_i2c_irq,
+					  irqflags | IRQF_ONESHOT,
+					  client->name, ts);
+	if (error) {
+		dev_err(&client->dev, "Failed to register interrupt\n");
+		return error;
+	}
+
+	/*
+	 * Systems using device tree should set up wakeup via DTS,
+	 * the rest will configure device as wakeup source by default.
+	 */
+	if (!client->dev.of_node)
+		device_init_wakeup(&client->dev, true);
+
+	error = sysfs_create_group(&client->dev.kobj, &elants_attribute_group);
+	if (error) {
+		dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
+			error);
+		return error;
+	}
+
+	error = devm_add_action(&client->dev,
+				elants_i2c_remove_sysfs_group, ts);
+	if (error) {
+		elants_i2c_remove_sysfs_group(ts);
+		dev_err(&client->dev,
+			"Failed to add sysfs cleanup action: %d\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int __maybe_unused elants_i2c_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elants_data *ts = i2c_get_clientdata(client);
+	const u8 set_sleep_cmd[] = { 0x54, 0x50, 0x00, 0x01 };
+	int retry_cnt;
+	int error;
+
+	/* Command not support in IAP recovery mode */
+	if (ts->iap_mode != ELAN_IAP_OPERATIONAL)
+		return -EBUSY;
+
+	disable_irq(client->irq);
+
+	for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
+		error = elants_i2c_send(client, set_sleep_cmd,
+					sizeof(set_sleep_cmd));
+		if (!error)
+			break;
+
+		dev_err(&client->dev, "suspend command failed: %d\n", error);
+	}
+
+	if (device_may_wakeup(dev))
+		ts->wake_irq_enabled = (enable_irq_wake(client->irq) == 0);
+
+	return 0;
+}
+
+static int __maybe_unused elants_i2c_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct elants_data *ts = i2c_get_clientdata(client);
+	const u8 set_active_cmd[] = { 0x54, 0x58, 0x00, 0x01 };
+	int retry_cnt;
+	int error;
+
+	if (device_may_wakeup(dev) && ts->wake_irq_enabled)
+		disable_irq_wake(client->irq);
+
+	for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
+		error = elants_i2c_send(client, set_active_cmd,
+					sizeof(set_active_cmd));
+		if (!error)
+			break;
+
+		dev_err(&client->dev, "resume command failed: %d\n", error);
+	}
+
+	ts->state = ELAN_STATE_NORMAL;
+	enable_irq(client->irq);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(elants_i2c_pm_ops,
+			 elants_i2c_suspend, elants_i2c_resume);
+
+static const struct i2c_device_id elants_i2c_id[] = {
+	{ DEVICE_NAME, 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, elants_i2c_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id elants_acpi_id[] = {
+	{ "ELAN0001", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, elants_acpi_id);
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id elants_of_match[] = {
+	{ .compatible = "elan,ekth3500" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, elants_of_match);
+#endif
+
+static struct i2c_driver elants_i2c_driver = {
+	.probe = elants_i2c_probe,
+	.id_table = elants_i2c_id,
+	.driver = {
+		.name = DEVICE_NAME,
+		.owner = THIS_MODULE,
+		.pm = &elants_i2c_pm_ops,
+		.acpi_match_table = ACPI_PTR(elants_acpi_id),
+		.of_match_table = of_match_ptr(elants_of_match),
+	},
+};
+module_i2c_driver(elants_i2c_driver);
+
+MODULE_AUTHOR("Scott Liu <scott.liu@emc.com.tw>");
+MODULE_DESCRIPTION("Elan I2c Touchscreen driver");
+MODULE_VERSION(DRV_VERSION);
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
new file mode 100644
index 0000000..ca19668
--- /dev/null
+++ b/drivers/input/touchscreen/goodix.c
@@ -0,0 +1,395 @@
+/*
+ *  Driver for Goodix Touchscreens
+ *
+ *  Copyright (c) 2014 Red Hat Inc.
+ *
+ *  This code is based on gt9xx.c authored by andrew@goodix.com:
+ *
+ *  2010 - 2012 Goodix Technology.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; version 2 of the License.
+ */
+
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <asm/unaligned.h>
+
+struct goodix_ts_data {
+	struct i2c_client *client;
+	struct input_dev *input_dev;
+	int abs_x_max;
+	int abs_y_max;
+	unsigned int max_touch_num;
+	unsigned int int_trigger_type;
+};
+
+#define GOODIX_MAX_HEIGHT		4096
+#define GOODIX_MAX_WIDTH		4096
+#define GOODIX_INT_TRIGGER		1
+#define GOODIX_CONTACT_SIZE		8
+#define GOODIX_MAX_CONTACTS		10
+
+#define GOODIX_CONFIG_MAX_LENGTH	240
+
+/* Register defines */
+#define GOODIX_READ_COOR_ADDR		0x814E
+#define GOODIX_REG_CONFIG_DATA		0x8047
+#define GOODIX_REG_VERSION		0x8140
+
+#define RESOLUTION_LOC		1
+#define TRIGGER_LOC		6
+
+static const unsigned long goodix_irq_flags[] = {
+	IRQ_TYPE_EDGE_RISING,
+	IRQ_TYPE_EDGE_FALLING,
+	IRQ_TYPE_LEVEL_LOW,
+	IRQ_TYPE_LEVEL_HIGH,
+};
+
+/**
+ * goodix_i2c_read - read data from a register of the i2c slave device.
+ *
+ * @client: i2c device.
+ * @reg: the register to read from.
+ * @buf: raw write data buffer.
+ * @len: length of the buffer to write
+ */
+static int goodix_i2c_read(struct i2c_client *client,
+				u16 reg, u8 *buf, int len)
+{
+	struct i2c_msg msgs[2];
+	u16 wbuf = cpu_to_be16(reg);
+	int ret;
+
+	msgs[0].flags = 0;
+	msgs[0].addr  = client->addr;
+	msgs[0].len   = 2;
+	msgs[0].buf   = (u8 *) &wbuf;
+
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].addr  = client->addr;
+	msgs[1].len   = len;
+	msgs[1].buf   = buf;
+
+	ret = i2c_transfer(client->adapter, msgs, 2);
+	return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
+}
+
+static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
+{
+	int touch_num;
+	int error;
+
+	error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR, data,
+				GOODIX_CONTACT_SIZE + 1);
+	if (error) {
+		dev_err(&ts->client->dev, "I2C transfer error: %d\n", error);
+		return error;
+	}
+
+	touch_num = data[0] & 0x0f;
+	if (touch_num > GOODIX_MAX_CONTACTS)
+		return -EPROTO;
+
+	if (touch_num > 1) {
+		data += 1 + GOODIX_CONTACT_SIZE;
+		error = goodix_i2c_read(ts->client,
+					GOODIX_READ_COOR_ADDR +
+						1 + GOODIX_CONTACT_SIZE,
+					data,
+					GOODIX_CONTACT_SIZE * (touch_num - 1));
+		if (error)
+			return error;
+	}
+
+	return touch_num;
+}
+
+static void goodix_ts_report_touch(struct goodix_ts_data *ts, u8 *coor_data)
+{
+	int id = coor_data[0] & 0x0F;
+	int input_x = get_unaligned_le16(&coor_data[1]);
+	int input_y = get_unaligned_le16(&coor_data[3]);
+	int input_w = get_unaligned_le16(&coor_data[5]);
+
+	input_mt_slot(ts->input_dev, id);
+	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
+	input_report_abs(ts->input_dev, ABS_MT_POSITION_X, input_x);
+	input_report_abs(ts->input_dev, ABS_MT_POSITION_Y, input_y);
+	input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, input_w);
+	input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
+}
+
+/**
+ * goodix_process_events - Process incoming events
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Called when the IRQ is triggered. Read the current device state, and push
+ * the input events to the user space.
+ */
+static void goodix_process_events(struct goodix_ts_data *ts)
+{
+	u8  point_data[1 + GOODIX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
+	int touch_num;
+	int i;
+
+	touch_num = goodix_ts_read_input_report(ts, point_data);
+	if (touch_num < 0)
+		return;
+
+	for (i = 0; i < touch_num; i++)
+		goodix_ts_report_touch(ts,
+				&point_data[1 + GOODIX_CONTACT_SIZE * i]);
+
+	input_mt_sync_frame(ts->input_dev);
+	input_sync(ts->input_dev);
+}
+
+/**
+ * goodix_ts_irq_handler - The IRQ handler
+ *
+ * @irq: interrupt number.
+ * @dev_id: private data pointer.
+ */
+static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
+{
+	static const u8 end_cmd[] = {
+		GOODIX_READ_COOR_ADDR >> 8,
+		GOODIX_READ_COOR_ADDR & 0xff,
+		0
+	};
+	struct goodix_ts_data *ts = dev_id;
+
+	goodix_process_events(ts);
+
+	if (i2c_master_send(ts->client, end_cmd, sizeof(end_cmd)) < 0)
+		dev_err(&ts->client->dev, "I2C write end_cmd error\n");
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * goodix_read_config - Read the embedded configuration of the panel
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called during probe
+ */
+static void goodix_read_config(struct goodix_ts_data *ts)
+{
+	u8 config[GOODIX_CONFIG_MAX_LENGTH];
+	int error;
+
+	error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
+			      config,
+			   GOODIX_CONFIG_MAX_LENGTH);
+	if (error) {
+		dev_warn(&ts->client->dev,
+			 "Error reading config (%d), using defaults\n",
+			 error);
+		ts->abs_x_max = GOODIX_MAX_WIDTH;
+		ts->abs_y_max = GOODIX_MAX_HEIGHT;
+		ts->int_trigger_type = GOODIX_INT_TRIGGER;
+		return;
+	}
+
+	ts->abs_x_max = get_unaligned_le16(&config[RESOLUTION_LOC]);
+	ts->abs_y_max = get_unaligned_le16(&config[RESOLUTION_LOC + 2]);
+	ts->int_trigger_type = (config[TRIGGER_LOC]) & 0x03;
+	if (!ts->abs_x_max || !ts->abs_y_max) {
+		dev_err(&ts->client->dev,
+			"Invalid config, using defaults\n");
+		ts->abs_x_max = GOODIX_MAX_WIDTH;
+		ts->abs_y_max = GOODIX_MAX_HEIGHT;
+	}
+}
+
+
+/**
+ * goodix_read_version - Read goodix touchscreen version
+ *
+ * @client: the i2c client
+ * @version: output buffer containing the version on success
+ */
+static int goodix_read_version(struct i2c_client *client, u16 *version)
+{
+	int error;
+	u8 buf[6];
+
+	error = goodix_i2c_read(client, GOODIX_REG_VERSION, buf, sizeof(buf));
+	if (error) {
+		dev_err(&client->dev, "read version failed: %d\n", error);
+		return error;
+	}
+
+	if (version)
+		*version = get_unaligned_le16(&buf[4]);
+
+	dev_info(&client->dev, "IC VERSION: %6ph\n", buf);
+
+	return 0;
+}
+
+/**
+ * goodix_i2c_test - I2C test function to check if the device answers.
+ *
+ * @client: the i2c client
+ */
+static int goodix_i2c_test(struct i2c_client *client)
+{
+	int retry = 0;
+	int error;
+	u8 test;
+
+	while (retry++ < 2) {
+		error = goodix_i2c_read(client, GOODIX_REG_CONFIG_DATA,
+					&test, 1);
+		if (!error)
+			return 0;
+
+		dev_err(&client->dev, "i2c test failed attempt %d: %d\n",
+			retry, error);
+		msleep(20);
+	}
+
+	return error;
+}
+
+/**
+ * goodix_request_input_dev - Allocate, populate and register the input device
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called during probe
+ */
+static int goodix_request_input_dev(struct goodix_ts_data *ts)
+{
+	int error;
+
+	ts->input_dev = devm_input_allocate_device(&ts->client->dev);
+	if (!ts->input_dev) {
+		dev_err(&ts->client->dev, "Failed to allocate input device.");
+		return -ENOMEM;
+	}
+
+	ts->input_dev->evbit[0] = BIT_MASK(EV_SYN) |
+				  BIT_MASK(EV_KEY) |
+				  BIT_MASK(EV_ABS);
+
+	input_set_abs_params(ts->input_dev, ABS_MT_POSITION_X, 0,
+				ts->abs_x_max, 0, 0);
+	input_set_abs_params(ts->input_dev, ABS_MT_POSITION_Y, 0,
+				ts->abs_y_max, 0, 0);
+	input_set_abs_params(ts->input_dev, ABS_MT_WIDTH_MAJOR, 0, 255, 0, 0);
+	input_set_abs_params(ts->input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
+
+	input_mt_init_slots(ts->input_dev, GOODIX_MAX_CONTACTS,
+			    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
+
+	ts->input_dev->name = "Goodix Capacitive TouchScreen";
+	ts->input_dev->phys = "input/ts";
+	ts->input_dev->id.bustype = BUS_I2C;
+	ts->input_dev->id.vendor = 0x0416;
+	ts->input_dev->id.product = 0x1001;
+	ts->input_dev->id.version = 10427;
+
+	error = input_register_device(ts->input_dev);
+	if (error) {
+		dev_err(&ts->client->dev,
+			"Failed to register input device: %d", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int goodix_ts_probe(struct i2c_client *client,
+			   const struct i2c_device_id *id)
+{
+	struct goodix_ts_data *ts;
+	unsigned long irq_flags;
+	int error;
+	u16 version_info;
+
+	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "I2C check functionality failed.\n");
+		return -ENXIO;
+	}
+
+	ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	ts->client = client;
+	i2c_set_clientdata(client, ts);
+
+	error = goodix_i2c_test(client);
+	if (error) {
+		dev_err(&client->dev, "I2C communication failure: %d\n", error);
+		return error;
+	}
+
+	error = goodix_read_version(client, &version_info);
+	if (error) {
+		dev_err(&client->dev, "Read version failed.\n");
+		return error;
+	}
+
+	goodix_read_config(ts);
+
+	error = goodix_request_input_dev(ts);
+	if (error)
+		return error;
+
+	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+	error = devm_request_threaded_irq(&ts->client->dev, client->irq,
+					  NULL, goodix_ts_irq_handler,
+					  irq_flags, client->name, ts);
+	if (error) {
+		dev_err(&client->dev, "request IRQ failed: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id goodix_ts_id[] = {
+	{ "GDIX1001:00", 0 },
+	{ }
+};
+
+static const struct acpi_device_id goodix_acpi_match[] = {
+	{ "GDIX1001", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, goodix_acpi_match);
+
+static struct i2c_driver goodix_ts_driver = {
+	.probe = goodix_ts_probe,
+	.id_table = goodix_ts_id,
+	.driver = {
+		.name = "Goodix-TS",
+		.owner = THIS_MODULE,
+		.acpi_match_table = goodix_acpi_match,
+	},
+};
+module_i2c_driver(goodix_ts_driver);
+
+MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>");
+MODULE_AUTHOR("Bastien Nocera <hadess@hadess.net>");
+MODULE_DESCRIPTION("Goodix touchscreen driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/touchscreen/ili210x.c b/drivers/input/touchscreen/ili210x.c
index 2a50891..da6dc81 100644
--- a/drivers/input/touchscreen/ili210x.c
+++ b/drivers/input/touchscreen/ili210x.c
@@ -311,8 +311,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int ili210x_i2c_suspend(struct device *dev)
+static int __maybe_unused ili210x_i2c_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
@@ -322,7 +321,7 @@
 	return 0;
 }
 
-static int ili210x_i2c_resume(struct device *dev)
+static int __maybe_unused ili210x_i2c_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
@@ -331,7 +330,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(ili210x_i2c_pm,
 			 ili210x_i2c_suspend, ili210x_i2c_resume);
diff --git a/drivers/input/touchscreen/ipaq-micro-ts.c b/drivers/input/touchscreen/ipaq-micro-ts.c
index 62c8976..33c1348 100644
--- a/drivers/input/touchscreen/ipaq-micro-ts.c
+++ b/drivers/input/touchscreen/ipaq-micro-ts.c
@@ -122,8 +122,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int micro_ts_suspend(struct device *dev)
+static int __maybe_unused micro_ts_suspend(struct device *dev)
 {
 	struct touchscreen_data *ts = dev_get_drvdata(dev);
 
@@ -132,7 +131,7 @@
 	return 0;
 }
 
-static int micro_ts_resume(struct device *dev)
+static int __maybe_unused micro_ts_resume(struct device *dev)
 {
 	struct touchscreen_data *ts = dev_get_drvdata(dev);
 	struct input_dev *input = ts->input;
@@ -146,7 +145,6 @@
 
 	return 0;
 }
-#endif
 
 static const struct dev_pm_ops micro_ts_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(micro_ts_suspend, micro_ts_resume)
diff --git a/drivers/input/touchscreen/mms114.c b/drivers/input/touchscreen/mms114.c
index 372bbf7..67c0d31 100644
--- a/drivers/input/touchscreen/mms114.c
+++ b/drivers/input/touchscreen/mms114.c
@@ -515,8 +515,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int mms114_suspend(struct device *dev)
+static int __maybe_unused mms114_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct mms114_data *data = i2c_get_clientdata(client);
@@ -540,7 +539,7 @@
 	return 0;
 }
 
-static int mms114_resume(struct device *dev)
+static int __maybe_unused mms114_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct mms114_data *data = i2c_get_clientdata(client);
@@ -559,7 +558,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(mms114_pm_ops, mms114_suspend, mms114_resume);
 
diff --git a/drivers/input/touchscreen/pixcir_i2c_ts.c b/drivers/input/touchscreen/pixcir_i2c_ts.c
index fc49c753..4fb5537 100644
--- a/drivers/input/touchscreen/pixcir_i2c_ts.c
+++ b/drivers/input/touchscreen/pixcir_i2c_ts.c
@@ -347,8 +347,7 @@
 	pixcir_stop(ts);
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int pixcir_i2c_ts_suspend(struct device *dev)
+static int __maybe_unused pixcir_i2c_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct pixcir_i2c_ts_data *ts = i2c_get_clientdata(client);
@@ -377,7 +376,7 @@
 	return ret;
 }
 
-static int pixcir_i2c_ts_resume(struct device *dev)
+static int __maybe_unused pixcir_i2c_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct pixcir_i2c_ts_data *ts = i2c_get_clientdata(client);
@@ -405,7 +404,6 @@
 
 	return ret;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(pixcir_dev_pm_ops,
 			 pixcir_i2c_ts_suspend, pixcir_i2c_ts_resume);
diff --git a/drivers/input/touchscreen/st1232.c b/drivers/input/touchscreen/st1232.c
index 3c0f57e..697e26e 100644
--- a/drivers/input/touchscreen/st1232.c
+++ b/drivers/input/touchscreen/st1232.c
@@ -243,8 +243,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int st1232_ts_suspend(struct device *dev)
+static int __maybe_unused st1232_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct st1232_ts_data *ts = i2c_get_clientdata(client);
@@ -259,7 +258,7 @@
 	return 0;
 }
 
-static int st1232_ts_resume(struct device *dev)
+static int __maybe_unused st1232_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct st1232_ts_data *ts = i2c_get_clientdata(client);
@@ -274,8 +273,6 @@
 	return 0;
 }
 
-#endif
-
 static SIMPLE_DEV_PM_OPS(st1232_ts_pm_ops,
 			 st1232_ts_suspend, st1232_ts_resume);
 
diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c
index 52380b6..72657c5 100644
--- a/drivers/input/touchscreen/tsc2005.c
+++ b/drivers/input/touchscreen/tsc2005.c
@@ -773,8 +773,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int tsc2005_suspend(struct device *dev)
+static int __maybe_unused tsc2005_suspend(struct device *dev)
 {
 	struct spi_device *spi = to_spi_device(dev);
 	struct tsc2005 *ts = spi_get_drvdata(spi);
@@ -791,7 +790,7 @@
 	return 0;
 }
 
-static int tsc2005_resume(struct device *dev)
+static int __maybe_unused tsc2005_resume(struct device *dev)
 {
 	struct spi_device *spi = to_spi_device(dev);
 	struct tsc2005 *ts = spi_get_drvdata(spi);
@@ -807,7 +806,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(tsc2005_pm_ops, tsc2005_suspend, tsc2005_resume);
 
diff --git a/drivers/input/touchscreen/ucb1400_ts.c b/drivers/input/touchscreen/ucb1400_ts.c
index 0eca00d..c1e23cf 100644
--- a/drivers/input/touchscreen/ucb1400_ts.c
+++ b/drivers/input/touchscreen/ucb1400_ts.c
@@ -406,8 +406,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int ucb1400_ts_suspend(struct device *dev)
+static int __maybe_unused ucb1400_ts_suspend(struct device *dev)
 {
 	struct ucb1400_ts *ucb = dev_get_platdata(dev);
 	struct input_dev *idev = ucb->ts_idev;
@@ -421,7 +420,7 @@
 	return 0;
 }
 
-static int ucb1400_ts_resume(struct device *dev)
+static int __maybe_unused ucb1400_ts_resume(struct device *dev)
 {
 	struct ucb1400_ts *ucb = dev_get_platdata(dev);
 	struct input_dev *idev = ucb->ts_idev;
@@ -434,7 +433,6 @@
 	mutex_unlock(&idev->mutex);
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(ucb1400_ts_pm_ops,
 			 ucb1400_ts_suspend, ucb1400_ts_resume);
diff --git a/drivers/input/touchscreen/wacom_i2c.c b/drivers/input/touchscreen/wacom_i2c.c
index 7ccaa1b..32f8ac0 100644
--- a/drivers/input/touchscreen/wacom_i2c.c
+++ b/drivers/input/touchscreen/wacom_i2c.c
@@ -242,8 +242,7 @@
 	return 0;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int wacom_i2c_suspend(struct device *dev)
+static int __maybe_unused wacom_i2c_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
@@ -252,7 +251,7 @@
 	return 0;
 }
 
-static int wacom_i2c_resume(struct device *dev)
+static int __maybe_unused wacom_i2c_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 
@@ -260,7 +259,6 @@
 
 	return 0;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(wacom_i2c_pm, wacom_i2c_suspend, wacom_i2c_resume);
 
diff --git a/drivers/input/touchscreen/zforce_ts.c b/drivers/input/touchscreen/zforce_ts.c
index 8ba48f5..19880c7 100644
--- a/drivers/input/touchscreen/zforce_ts.c
+++ b/drivers/input/touchscreen/zforce_ts.c
@@ -602,8 +602,7 @@
 	return;
 }
 
-#ifdef CONFIG_PM_SLEEP
-static int zforce_suspend(struct device *dev)
+static int __maybe_unused zforce_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct zforce_ts *ts = i2c_get_clientdata(client);
@@ -648,7 +647,7 @@
 	return ret;
 }
 
-static int zforce_resume(struct device *dev)
+static int __maybe_unused zforce_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct zforce_ts *ts = i2c_get_clientdata(client);
@@ -685,7 +684,6 @@
 
 	return ret;
 }
-#endif
 
 static SIMPLE_DEV_PM_OPS(zforce_pm_ops, zforce_suspend, zforce_resume);