Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intende for the 3.14 stream...
For the mac80211 bits, Johannes says:
"Here I have a fix from Eliad for the minimal channel width calculation
in the mac80211 code which lead to monitor mode not working at all for
drivers using that. One of my fixes is for an issue noticed by Michal,
we clear an already cleared value but do it without locking, so just
remove that. The other is for a data leak - we leak two bytes of kernel
memory out over the air in QoS NULL frames because those don't get a
sequence number assigned in the TX path."
For the iwlwifi bits, Emmanuel says:
"One more fix and an update for device IDs.
There is a bugzilla reported for the fix which is mentioned in the commit message."
Along with those...
Amitkumar Karwar provides two mwifiex fixes, both correcting some
data transcription problems.
Ivaylo Dimitrov uses skb_trim in the wl1251 driver to avoid
HAVE_EFFICIENT_UNALIGNED_ACCESS problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/bnx2.c b/drivers/net/ethernet/broadcom/bnx2.c
index cda25ac..6c9e1c9 100644
--- a/drivers/net/ethernet/broadcom/bnx2.c
+++ b/drivers/net/ethernet/broadcom/bnx2.c
@@ -2507,6 +2507,7 @@
bp->fw_wr_seq++;
msg_data |= bp->fw_wr_seq;
+ bp->fw_last_msg = msg_data;
bnx2_shmem_wr(bp, BNX2_DRV_MB, msg_data);
@@ -4000,8 +4001,23 @@
wol_msg = BNX2_DRV_MSG_CODE_SUSPEND_NO_WOL;
}
- if (!(bp->flags & BNX2_FLAG_NO_WOL))
- bnx2_fw_sync(bp, BNX2_DRV_MSG_DATA_WAIT3 | wol_msg, 1, 0);
+ if (!(bp->flags & BNX2_FLAG_NO_WOL)) {
+ u32 val;
+
+ wol_msg |= BNX2_DRV_MSG_DATA_WAIT3;
+ if (bp->fw_last_msg || BNX2_CHIP(bp) != BNX2_CHIP_5709) {
+ bnx2_fw_sync(bp, wol_msg, 1, 0);
+ return;
+ }
+ /* Tell firmware not to power down the PHY yet, otherwise
+ * the chip will take a long time to respond to MMIO reads.
+ */
+ val = bnx2_shmem_rd(bp, BNX2_PORT_FEATURE);
+ bnx2_shmem_wr(bp, BNX2_PORT_FEATURE,
+ val | BNX2_PORT_FEATURE_ASF_ENABLED);
+ bnx2_fw_sync(bp, wol_msg, 1, 0);
+ bnx2_shmem_wr(bp, BNX2_PORT_FEATURE, val);
+ }
}
@@ -4033,9 +4049,22 @@
if (bp->wol)
pci_set_power_state(bp->pdev, PCI_D3hot);
- } else {
- pci_set_power_state(bp->pdev, PCI_D3hot);
+ break;
+
}
+ if (!bp->fw_last_msg && BNX2_CHIP(bp) == BNX2_CHIP_5709) {
+ u32 val;
+
+ /* Tell firmware not to power down the PHY yet,
+ * otherwise the other port may not respond to
+ * MMIO reads.
+ */
+ val = bnx2_shmem_rd(bp, BNX2_BC_STATE_CONDITION);
+ val &= ~BNX2_CONDITION_PM_STATE_MASK;
+ val |= BNX2_CONDITION_PM_STATE_UNPREP;
+ bnx2_shmem_wr(bp, BNX2_BC_STATE_CONDITION, val);
+ }
+ pci_set_power_state(bp->pdev, PCI_D3hot);
/* No more memory access after this point until
* device is brought back to D0.
diff --git a/drivers/net/ethernet/broadcom/bnx2.h b/drivers/net/ethernet/broadcom/bnx2.h
index f1cf2c4..e341bc3 100644
--- a/drivers/net/ethernet/broadcom/bnx2.h
+++ b/drivers/net/ethernet/broadcom/bnx2.h
@@ -6900,6 +6900,7 @@
u16 fw_wr_seq;
u16 fw_drv_pulse_wr_seq;
+ u32 fw_last_msg;
int rx_max_ring;
int rx_ring_size;
@@ -7406,6 +7407,10 @@
#define BNX2_CONDITION_MFW_RUN_NCSI 0x00006000
#define BNX2_CONDITION_MFW_RUN_NONE 0x0000e000
#define BNX2_CONDITION_MFW_RUN_MASK 0x0000e000
+#define BNX2_CONDITION_PM_STATE_MASK 0x00030000
+#define BNX2_CONDITION_PM_STATE_FULL 0x00030000
+#define BNX2_CONDITION_PM_STATE_PREP 0x00020000
+#define BNX2_CONDITION_PM_STATE_UNPREP 0x00010000
#define BNX2_BC_STATE_DEBUG_CMD 0x1dc
#define BNX2_BC_STATE_BC_DBG_CMD_SIGNATURE 0x42440000
