Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
new file mode 100644
index 0000000..5ddb2e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
@@ -0,0 +1,84 @@
+Device tree bindings for OMAP general purpose memory controllers (GPMC)
+
+The actual devices are instantiated from the child nodes of a GPMC node.
+
+Required properties:
+
+ - compatible: Should be set to one of the following:
+
+ ti,omap2420-gpmc (omap2420)
+ ti,omap2430-gpmc (omap2430)
+ ti,omap3430-gpmc (omap3430 & omap3630)
+ ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
+ ti,am3352-gpmc (am335x devices)
+
+ - reg: A resource specifier for the register space
+ (see the example below)
+ - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is
+ completed.
+ - #address-cells: Must be set to 2 to allow memory address translation
+ - #size-cells: Must be set to 1 to allow CS address passing
+ - gpmc,num-cs: The maximum number of chip-select lines that controller
+ can support.
+ - gpmc,num-waitpins: The maximum number of wait pins that controller can
+ support.
+ - ranges: Must be set up to reflect the memory layout with four
+ integer values for each chip-select line in use:
+
+ <cs-number> 0 <physical address of mapping> <size>
+
+ Currently, calculated values derived from the contents
+ of the per-CS register GPMC_CONFIG7 (as set up by the
+ bootloader) are used for the physical address decoding.
+ As this will change in the future, filling correct
+ values here is a requirement.
+
+Timing properties for child nodes. All are optional and default to 0.
+
+ - gpmc,sync-clk: Minimum clock period for synchronous mode, in picoseconds
+
+ Chip-select signal timings corresponding to GPMC_CONFIG2:
+ - gpmc,cs-on: Assertion time
+ - gpmc,cs-rd-off: Read deassertion time
+ - gpmc,cs-wr-off: Write deassertion time
+
+ ADV signal timings corresponding to GPMC_CONFIG3:
+ - gpmc,adv-on: Assertion time
+ - gpmc,adv-rd-off: Read deassertion time
+ - gpmc,adv-wr-off: Write deassertion time
+
+ WE signals timings corresponding to GPMC_CONFIG4:
+ - gpmc,we-on: Assertion time
+ - gpmc,we-off: Deassertion time
+
+ OE signals timings corresponding to GPMC_CONFIG4:
+ - gpmc,oe-on: Assertion time
+ - gpmc,oe-off: Deassertion time
+
+ Access time and cycle time timings corresponding to GPMC_CONFIG5:
+ - gpmc,page-burst-access: Multiple access word delay
+ - gpmc,access: Start-cycle to first data valid delay
+ - gpmc,rd-cycle: Total read cycle time
+ - gpmc,wr-cycle: Total write cycle time
+
+The following are only applicable to OMAP3+ and AM335x:
+ - gpmc,wr-access
+ - gpmc,wr-data-mux-bus
+
+
+Example for an AM33xx board:
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x50000000 0x2000>;
+ interrupts = <100>;
+
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+
+ /* child nodes go here */
+ };
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
new file mode 100644
index 0000000..e7f8d7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -0,0 +1,80 @@
+Device tree bindings for GPMC connected NANDs
+
+GPMC connected NAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "nand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For NAND specific properties such as ECC modes or bus width, please refer to
+Documentation/devicetree/bindings/mtd/nand.txt
+
+
+Required properties:
+
+ - reg: The CS line the peripheral is connected to
+
+Optional properties:
+
+ - nand-bus-width: Set this numeric value to 16 if the hardware
+ is wired that way. If not specified, a bus
+ width of 8 is assumed.
+
+ - ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
+
+ "sw" Software method (default)
+ "hw" Hardware method
+ "hw-romcode" gpmc hamming mode method & romcode layout
+ "bch4" 4-bit BCH ecc code
+ "bch8" 8-bit BCH ecc code
+
+ - elm_id: Specifies elm device node. This is required to support BCH
+ error correction using ELM module.
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an AM33xx board:
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x50000000 0x1000000>;
+ interrupts = <100>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */
+ elm_id = <&elm>;
+
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+
+ gpmc,sync-clk = <0>;
+ gpmc,cs-on = <0>;
+ gpmc,cs-rd-off = <44>;
+ gpmc,cs-wr-off = <44>;
+ gpmc,adv-on = <6>;
+ gpmc,adv-rd-off = <34>;
+ gpmc,adv-wr-off = <44>;
+ gpmc,we-off = <40>;
+ gpmc,oe-off = <54>;
+ gpmc,access = <64>;
+ gpmc,rd-cycle = <82>;
+ gpmc,wr-cycle = <82>;
+ gpmc,wr-access = <40>;
+ gpmc,wr-data-mux-bus = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* partitions go here */
+ };
+ };
+
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
new file mode 100644
index 0000000..deec9da
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
@@ -0,0 +1,43 @@
+Device tree bindings for GPMC connected OneNANDs
+
+GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "onenand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+
+ - reg: The CS line the peripheral is connected to
+
+Optional properties:
+
+ - dma-channel: DMA Channel index
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an OMAP3430 board:
+
+ gpmc: gpmc@6e000000 {
+ compatible = "ti,omap3430-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x6e000000 0x1000000>;
+ interrupts = <20>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ onenand@0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* partitions go here */
+ };
+ };
diff --git a/arch/arm/mach-omap2/gpmc-nand.c b/arch/arm/mach-omap2/gpmc-nand.c
index db969a5..afc1e8c 100644
--- a/arch/arm/mach-omap2/gpmc-nand.c
+++ b/arch/arm/mach-omap2/gpmc-nand.c
@@ -89,20 +89,21 @@
return 0;
}
-static bool __init gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
+static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
{
/* support only OMAP3 class */
- if (!cpu_is_omap34xx()) {
+ if (!cpu_is_omap34xx() && !soc_is_am33xx()) {
pr_err("BCH ecc is not supported on this CPU\n");
return 0;
}
/*
- * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1.
- * Other chips may be added if confirmed to work.
+ * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1
+ * and AM33xx derivates. Other chips may be added if confirmed to work.
*/
if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) &&
- (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0))) {
+ (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)) &&
+ (!soc_is_am33xx())) {
pr_err("BCH 4-bit mode is not supported on this CPU\n");
return 0;
}
@@ -110,8 +111,8 @@
return 1;
}
-int __init gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
- struct gpmc_timings *gpmc_t)
+int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
+ struct gpmc_timings *gpmc_t)
{
int err = 0;
struct device *dev = &gpmc_nand_device.dev;
diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c
index 94a349e..fadd8743 100644
--- a/arch/arm/mach-omap2/gpmc-onenand.c
+++ b/arch/arm/mach-omap2/gpmc-onenand.c
@@ -356,7 +356,7 @@
return ret;
}
-void __init gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data)
+void gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data)
{
int err;
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index 64bac53..03d7713 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -25,6 +25,10 @@
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_mtd.h>
+#include <linux/of_device.h>
+#include <linux/mtd/nand.h>
#include <linux/platform_data/mtd-nand-omap2.h>
@@ -34,6 +38,8 @@
#include "common.h"
#include "omap_device.h"
#include "gpmc.h"
+#include "gpmc-nand.h"
+#include "gpmc-onenand.h"
#define DEVICE_NAME "omap-gpmc"
@@ -145,7 +151,8 @@
static struct resource gpmc_mem_root;
static struct resource gpmc_cs_mem[GPMC_CS_NUM];
static DEFINE_SPINLOCK(gpmc_mem_lock);
-static unsigned int gpmc_cs_map; /* flag for cs which are initialized */
+/* Define chip-selects as reserved by default until probe completes */
+static unsigned int gpmc_cs_map = ((1 << GPMC_CS_NUM) - 1);
static struct device *gpmc_dev;
static int gpmc_irq;
static resource_size_t phys_base, mem_size;
@@ -1118,9 +1125,216 @@
/* TODO: remove, see function definition */
gpmc_convert_ps_to_ns(gpmc_t);
+ /* Now the GPMC is initialised, unreserve the chip-selects */
+ gpmc_cs_map = 0;
+
return 0;
}
+#ifdef CONFIG_OF
+static struct of_device_id gpmc_dt_ids[] = {
+ { .compatible = "ti,omap2420-gpmc" },
+ { .compatible = "ti,omap2430-gpmc" },
+ { .compatible = "ti,omap3430-gpmc" }, /* omap3430 & omap3630 */
+ { .compatible = "ti,omap4430-gpmc" }, /* omap4430 & omap4460 & omap543x */
+ { .compatible = "ti,am3352-gpmc" }, /* am335x devices */
+ { }
+};
+MODULE_DEVICE_TABLE(of, gpmc_dt_ids);
+
+static void __maybe_unused gpmc_read_timings_dt(struct device_node *np,
+ struct gpmc_timings *gpmc_t)
+{
+ u32 val;
+
+ memset(gpmc_t, 0, sizeof(*gpmc_t));
+
+ /* minimum clock period for syncronous mode */
+ if (!of_property_read_u32(np, "gpmc,sync-clk", &val))
+ gpmc_t->sync_clk = val;
+
+ /* chip select timtings */
+ if (!of_property_read_u32(np, "gpmc,cs-on", &val))
+ gpmc_t->cs_on = val;
+
+ if (!of_property_read_u32(np, "gpmc,cs-rd-off", &val))
+ gpmc_t->cs_rd_off = val;
+
+ if (!of_property_read_u32(np, "gpmc,cs-wr-off", &val))
+ gpmc_t->cs_wr_off = val;
+
+ /* ADV signal timings */
+ if (!of_property_read_u32(np, "gpmc,adv-on", &val))
+ gpmc_t->adv_on = val;
+
+ if (!of_property_read_u32(np, "gpmc,adv-rd-off", &val))
+ gpmc_t->adv_rd_off = val;
+
+ if (!of_property_read_u32(np, "gpmc,adv-wr-off", &val))
+ gpmc_t->adv_wr_off = val;
+
+ /* WE signal timings */
+ if (!of_property_read_u32(np, "gpmc,we-on", &val))
+ gpmc_t->we_on = val;
+
+ if (!of_property_read_u32(np, "gpmc,we-off", &val))
+ gpmc_t->we_off = val;
+
+ /* OE signal timings */
+ if (!of_property_read_u32(np, "gpmc,oe-on", &val))
+ gpmc_t->oe_on = val;
+
+ if (!of_property_read_u32(np, "gpmc,oe-off", &val))
+ gpmc_t->oe_off = val;
+
+ /* access and cycle timings */
+ if (!of_property_read_u32(np, "gpmc,page-burst-access", &val))
+ gpmc_t->page_burst_access = val;
+
+ if (!of_property_read_u32(np, "gpmc,access", &val))
+ gpmc_t->access = val;
+
+ if (!of_property_read_u32(np, "gpmc,rd-cycle", &val))
+ gpmc_t->rd_cycle = val;
+
+ if (!of_property_read_u32(np, "gpmc,wr-cycle", &val))
+ gpmc_t->wr_cycle = val;
+
+ /* only for OMAP3430 */
+ if (!of_property_read_u32(np, "gpmc,wr-access", &val))
+ gpmc_t->wr_access = val;
+
+ if (!of_property_read_u32(np, "gpmc,wr-data-mux-bus", &val))
+ gpmc_t->wr_data_mux_bus = val;
+}
+
+#ifdef CONFIG_MTD_NAND
+
+static const char * const nand_ecc_opts[] = {
+ [OMAP_ECC_HAMMING_CODE_DEFAULT] = "sw",
+ [OMAP_ECC_HAMMING_CODE_HW] = "hw",
+ [OMAP_ECC_HAMMING_CODE_HW_ROMCODE] = "hw-romcode",
+ [OMAP_ECC_BCH4_CODE_HW] = "bch4",
+ [OMAP_ECC_BCH8_CODE_HW] = "bch8",
+};
+
+static int gpmc_probe_nand_child(struct platform_device *pdev,
+ struct device_node *child)
+{
+ u32 val;
+ const char *s;
+ struct gpmc_timings gpmc_t;
+ struct omap_nand_platform_data *gpmc_nand_data;
+
+ if (of_property_read_u32(child, "reg", &val) < 0) {
+ dev_err(&pdev->dev, "%s has no 'reg' property\n",
+ child->full_name);
+ return -ENODEV;
+ }
+
+ gpmc_nand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_nand_data),
+ GFP_KERNEL);
+ if (!gpmc_nand_data)
+ return -ENOMEM;
+
+ gpmc_nand_data->cs = val;
+ gpmc_nand_data->of_node = child;
+
+ if (!of_property_read_string(child, "ti,nand-ecc-opt", &s))
+ for (val = 0; val < ARRAY_SIZE(nand_ecc_opts); val++)
+ if (!strcasecmp(s, nand_ecc_opts[val])) {
+ gpmc_nand_data->ecc_opt = val;
+ break;
+ }
+
+ val = of_get_nand_bus_width(child);
+ if (val == 16)
+ gpmc_nand_data->devsize = NAND_BUSWIDTH_16;
+
+ gpmc_read_timings_dt(child, &gpmc_t);
+ gpmc_nand_init(gpmc_nand_data, &gpmc_t);
+
+ return 0;
+}
+#else
+static int gpmc_probe_nand_child(struct platform_device *pdev,
+ struct device_node *child)
+{
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MTD_ONENAND
+static int gpmc_probe_onenand_child(struct platform_device *pdev,
+ struct device_node *child)
+{
+ u32 val;
+ struct omap_onenand_platform_data *gpmc_onenand_data;
+
+ if (of_property_read_u32(child, "reg", &val) < 0) {
+ dev_err(&pdev->dev, "%s has no 'reg' property\n",
+ child->full_name);
+ return -ENODEV;
+ }
+
+ gpmc_onenand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_onenand_data),
+ GFP_KERNEL);
+ if (!gpmc_onenand_data)
+ return -ENOMEM;
+
+ gpmc_onenand_data->cs = val;
+ gpmc_onenand_data->of_node = child;
+ gpmc_onenand_data->dma_channel = -1;
+
+ if (!of_property_read_u32(child, "dma-channel", &val))
+ gpmc_onenand_data->dma_channel = val;
+
+ gpmc_onenand_init(gpmc_onenand_data);
+
+ return 0;
+}
+#else
+static int gpmc_probe_onenand_child(struct platform_device *pdev,
+ struct device_node *child)
+{
+ return 0;
+}
+#endif
+
+static int gpmc_probe_dt(struct platform_device *pdev)
+{
+ int ret;
+ struct device_node *child;
+ const struct of_device_id *of_id =
+ of_match_device(gpmc_dt_ids, &pdev->dev);
+
+ if (!of_id)
+ return 0;
+
+ for_each_node_by_name(child, "nand") {
+ ret = gpmc_probe_nand_child(pdev, child);
+ if (ret < 0) {
+ of_node_put(child);
+ return ret;
+ }
+ }
+
+ for_each_node_by_name(child, "onenand") {
+ ret = gpmc_probe_onenand_child(pdev, child);
+ if (ret < 0) {
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+#else
+static int gpmc_probe_dt(struct platform_device *pdev)
+{
+ return 0;
+}
+#endif
+
static int gpmc_probe(struct platform_device *pdev)
{
int rc;
@@ -1172,6 +1386,14 @@
if (IS_ERR_VALUE(gpmc_setup_irq()))
dev_warn(gpmc_dev, "gpmc_setup_irq failed\n");
+ rc = gpmc_probe_dt(pdev);
+ if (rc < 0) {
+ clk_disable_unprepare(gpmc_l3_clk);
+ clk_put(gpmc_l3_clk);
+ dev_err(gpmc_dev, "failed to probe DT parameters\n");
+ return rc;
+ }
+
return 0;
}
@@ -1189,6 +1411,7 @@
.driver = {
.name = DEVICE_NAME,
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(gpmc_dt_ids),
},
};
@@ -1212,6 +1435,13 @@
struct platform_device *pdev;
char *oh_name = "gpmc";
+ /*
+ * if the board boots up with a populated DT, do not
+ * manually add the device from this initcall
+ */
+ if (of_have_populated_dt())
+ return -ENODEV;
+
oh = omap_hwmod_lookup(oh_name);
if (!oh) {
pr_err("Could not look up %s\n", oh_name);
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 12060ae..a683d17 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -31,6 +31,7 @@
#include <linux/dma-mapping.h>
#include <linux/platform_data/clk-u300.h>
#include <linux/platform_data/pinctrl-coh901.h>
+#include <linux/platform_data/dma-coh901318.h>
#include <linux/irqchip/arm-vic.h>
#include <asm/types.h>
@@ -40,7 +41,6 @@
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <mach/coh901318.h>
#include <mach/hardware.h>
#include <mach/syscon.h>
#include <mach/irqs.h>
@@ -49,7 +49,6 @@
#include "spi.h"
#include "i2c.h"
#include "u300-gpio.h"
-#include "dma_channels.h"
/*
* Static I/O mappings that are needed for booting the U300 platforms. The
@@ -327,1089 +326,6 @@
}
};
-/* points out all dma slave channels.
- * Syntax is [A1, B1, A2, B2, .... ,-1,-1]
- * Select all channels from A to B, end of list is marked with -1,-1
- */
-static int dma_slave_channels[] = {
- U300_DMA_MSL_TX_0, U300_DMA_SPI_RX,
- U300_DMA_UART1_TX, U300_DMA_UART1_RX, -1, -1};
-
-/* points out all dma memcpy channels. */
-static int dma_memcpy_channels[] = {
- U300_DMA_GENERAL_PURPOSE_0, U300_DMA_GENERAL_PURPOSE_8, -1, -1};
-
-/** register dma for memory access
- *
- * active 1 means dma intends to access memory
- * 0 means dma wont access memory
- */
-static void coh901318_access_memory_state(struct device *dev, bool active)
-{
-}
-
-#define flags_memcpy_config (COH901318_CX_CFG_CH_DISABLE | \
- COH901318_CX_CFG_RM_MEMORY_TO_MEMORY | \
- COH901318_CX_CFG_LCR_DISABLE | \
- COH901318_CX_CFG_TC_IRQ_ENABLE | \
- COH901318_CX_CFG_BE_IRQ_ENABLE)
-#define flags_memcpy_lli_chained (COH901318_CX_CTRL_TC_ENABLE | \
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
- COH901318_CX_CTRL_MASTER_MODE_M1RW | \
- COH901318_CX_CTRL_TCP_DISABLE | \
- COH901318_CX_CTRL_TC_IRQ_DISABLE | \
- COH901318_CX_CTRL_HSP_DISABLE | \
- COH901318_CX_CTRL_HSS_DISABLE | \
- COH901318_CX_CTRL_DDMA_LEGACY | \
- COH901318_CX_CTRL_PRDD_SOURCE)
-#define flags_memcpy_lli (COH901318_CX_CTRL_TC_ENABLE | \
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
- COH901318_CX_CTRL_MASTER_MODE_M1RW | \
- COH901318_CX_CTRL_TCP_DISABLE | \
- COH901318_CX_CTRL_TC_IRQ_DISABLE | \
- COH901318_CX_CTRL_HSP_DISABLE | \
- COH901318_CX_CTRL_HSS_DISABLE | \
- COH901318_CX_CTRL_DDMA_LEGACY | \
- COH901318_CX_CTRL_PRDD_SOURCE)
-#define flags_memcpy_lli_last (COH901318_CX_CTRL_TC_ENABLE | \
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
- COH901318_CX_CTRL_MASTER_MODE_M1RW | \
- COH901318_CX_CTRL_TCP_DISABLE | \
- COH901318_CX_CTRL_TC_IRQ_ENABLE | \
- COH901318_CX_CTRL_HSP_DISABLE | \
- COH901318_CX_CTRL_HSS_DISABLE | \
- COH901318_CX_CTRL_DDMA_LEGACY | \
- COH901318_CX_CTRL_PRDD_SOURCE)
-
-const struct coh_dma_channel chan_config[U300_DMA_CHANNELS] = {
- {
- .number = U300_DMA_MSL_TX_0,
- .name = "MSL TX 0",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 0 * 0x40 + 0x20,
- },
- {
- .number = U300_DMA_MSL_TX_1,
- .name = "MSL TX 1",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 1 * 0x40 + 0x20,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- },
- {
- .number = U300_DMA_MSL_TX_2,
- .name = "MSL TX 2",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 2 * 0x40 + 0x20,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .desc_nbr_max = 10,
- },
- {
- .number = U300_DMA_MSL_TX_3,
- .name = "MSL TX 3",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 3 * 0x40 + 0x20,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- },
- {
- .number = U300_DMA_MSL_TX_4,
- .name = "MSL TX 4",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 4 * 0x40 + 0x20,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- },
- {
- .number = U300_DMA_MSL_TX_5,
- .name = "MSL TX 5",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 5 * 0x40 + 0x20,
- },
- {
- .number = U300_DMA_MSL_TX_6,
- .name = "MSL TX 6",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 6 * 0x40 + 0x20,
- },
- {
- .number = U300_DMA_MSL_RX_0,
- .name = "MSL RX 0",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 0 * 0x40 + 0x220,
- },
- {
- .number = U300_DMA_MSL_RX_1,
- .name = "MSL RX 1",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 1 * 0x40 + 0x220,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_MSL_RX_2,
- .name = "MSL RX 2",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 2 * 0x40 + 0x220,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_MSL_RX_3,
- .name = "MSL RX 3",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 3 * 0x40 + 0x220,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_MSL_RX_4,
- .name = "MSL RX 4",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 4 * 0x40 + 0x220,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_MSL_RX_5,
- .name = "MSL RX 5",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 5 * 0x40 + 0x220,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_MSL_RX_6,
- .name = "MSL RX 6",
- .priority_high = 0,
- .dev_addr = U300_MSL_BASE + 6 * 0x40 + 0x220,
- },
- /*
- * Don't set up device address, burst count or size of src
- * or dst bus for this peripheral - handled by PrimeCell
- * DMA extension.
- */
- {
- .number = U300_DMA_MMCSD_RX_TX,
- .name = "MMCSD RX TX",
- .priority_high = 0,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
-
- },
- {
- .number = U300_DMA_MSPRO_TX,
- .name = "MSPRO TX",
- .priority_high = 0,
- },
- {
- .number = U300_DMA_MSPRO_RX,
- .name = "MSPRO RX",
- .priority_high = 0,
- },
- /*
- * Don't set up device address, burst count or size of src
- * or dst bus for this peripheral - handled by PrimeCell
- * DMA extension.
- */
- {
- .number = U300_DMA_UART0_TX,
- .name = "UART0 TX",
- .priority_high = 0,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- },
- {
- .number = U300_DMA_UART0_RX,
- .name = "UART0 RX",
- .priority_high = 0,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- },
- {
- .number = U300_DMA_APEX_TX,
- .name = "APEX TX",
- .priority_high = 0,
- },
- {
- .number = U300_DMA_APEX_RX,
- .name = "APEX RX",
- .priority_high = 0,
- },
- {
- .number = U300_DMA_PCM_I2S0_TX,
- .name = "PCM I2S0 TX",
- .priority_high = 1,
- .dev_addr = U300_PCM_I2S0_BASE + 0x14,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- },
- {
- .number = U300_DMA_PCM_I2S0_RX,
- .name = "PCM I2S0 RX",
- .priority_high = 1,
- .dev_addr = U300_PCM_I2S0_BASE + 0x10,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_PCM_I2S1_TX,
- .name = "PCM I2S1 TX",
- .priority_high = 1,
- .dev_addr = U300_PCM_I2S1_BASE + 0x14,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_SOURCE,
- },
- {
- .number = U300_DMA_PCM_I2S1_RX,
- .name = "PCM I2S1 RX",
- .priority_high = 1,
- .dev_addr = U300_PCM_I2S1_BASE + 0x10,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_DEST,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
- COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
- COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
- COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_ENABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY |
- COH901318_CX_CTRL_PRDD_DEST,
- },
- {
- .number = U300_DMA_XGAM_CDI,
- .name = "XGAM CDI",
- .priority_high = 0,
- },
- {
- .number = U300_DMA_XGAM_PDI,
- .name = "XGAM PDI",
- .priority_high = 0,
- },
- /*
- * Don't set up device address, burst count or size of src
- * or dst bus for this peripheral - handled by PrimeCell
- * DMA extension.
- */
- {
- .number = U300_DMA_SPI_TX,
- .name = "SPI TX",
- .priority_high = 0,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- },
- {
- .number = U300_DMA_SPI_RX,
- .name = "SPI RX",
- .priority_high = 0,
- .param.config = COH901318_CX_CFG_CH_DISABLE |
- COH901318_CX_CFG_LCR_DISABLE |
- COH901318_CX_CFG_TC_IRQ_ENABLE |
- COH901318_CX_CFG_BE_IRQ_ENABLE,
- .param.ctrl_lli_chained = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_DISABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
- .param.ctrl_lli_last = 0 |
- COH901318_CX_CTRL_TC_ENABLE |
- COH901318_CX_CTRL_MASTER_MODE_M1RW |
- COH901318_CX_CTRL_TCP_DISABLE |
- COH901318_CX_CTRL_TC_IRQ_ENABLE |
- COH901318_CX_CTRL_HSP_ENABLE |
- COH901318_CX_CTRL_HSS_DISABLE |
- COH901318_CX_CTRL_DDMA_LEGACY,
-
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_0,
- .name = "GENERAL 00",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_1,
- .name = "GENERAL 01",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_2,
- .name = "GENERAL 02",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_3,
- .name = "GENERAL 03",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_4,
- .name = "GENERAL 04",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_5,
- .name = "GENERAL 05",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_6,
- .name = "GENERAL 06",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_7,
- .name = "GENERAL 07",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_GENERAL_PURPOSE_8,
- .name = "GENERAL 08",
- .priority_high = 0,
-
- .param.config = flags_memcpy_config,
- .param.ctrl_lli_chained = flags_memcpy_lli_chained,
- .param.ctrl_lli = flags_memcpy_lli,
- .param.ctrl_lli_last = flags_memcpy_lli_last,
- },
- {
- .number = U300_DMA_UART1_TX,
- .name = "UART1 TX",
- .priority_high = 0,
- },
- {
- .number = U300_DMA_UART1_RX,
- .name = "UART1 RX",
- .priority_high = 0,
- }
-};
-
-
-static struct coh901318_platform coh901318_platform = {
- .chans_slave = dma_slave_channels,
- .chans_memcpy = dma_memcpy_channels,
- .access_memory_state = coh901318_access_memory_state,
- .chan_conf = chan_config,
- .max_channels = U300_DMA_CHANNELS,
-};
static struct resource pinctrl_resources[] = {
{
@@ -1521,7 +437,6 @@
.resource = dma_resource,
.num_resources = ARRAY_SIZE(dma_resource),
.dev = {
- .platform_data = &coh901318_platform,
.coherent_dma_mask = ~0,
},
};
diff --git a/arch/arm/mach-u300/dma_channels.h b/arch/arm/mach-u300/dma_channels.h
deleted file mode 100644
index 4e8a88f..0000000
--- a/arch/arm/mach-u300/dma_channels.h
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/include/mach/dma_channels.h
- *
- *
- * Copyright (C) 2007-2012 ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- * Map file for the U300 dma driver.
- * Author: Per Friden <per.friden@stericsson.com>
- */
-
-#ifndef DMA_CHANNELS_H
-#define DMA_CHANNELS_H
-
-#define U300_DMA_MSL_TX_0 0
-#define U300_DMA_MSL_TX_1 1
-#define U300_DMA_MSL_TX_2 2
-#define U300_DMA_MSL_TX_3 3
-#define U300_DMA_MSL_TX_4 4
-#define U300_DMA_MSL_TX_5 5
-#define U300_DMA_MSL_TX_6 6
-#define U300_DMA_MSL_RX_0 7
-#define U300_DMA_MSL_RX_1 8
-#define U300_DMA_MSL_RX_2 9
-#define U300_DMA_MSL_RX_3 10
-#define U300_DMA_MSL_RX_4 11
-#define U300_DMA_MSL_RX_5 12
-#define U300_DMA_MSL_RX_6 13
-#define U300_DMA_MMCSD_RX_TX 14
-#define U300_DMA_MSPRO_TX 15
-#define U300_DMA_MSPRO_RX 16
-#define U300_DMA_UART0_TX 17
-#define U300_DMA_UART0_RX 18
-#define U300_DMA_APEX_TX 19
-#define U300_DMA_APEX_RX 20
-#define U300_DMA_PCM_I2S0_TX 21
-#define U300_DMA_PCM_I2S0_RX 22
-#define U300_DMA_PCM_I2S1_TX 23
-#define U300_DMA_PCM_I2S1_RX 24
-#define U300_DMA_XGAM_CDI 25
-#define U300_DMA_XGAM_PDI 26
-#define U300_DMA_SPI_TX 27
-#define U300_DMA_SPI_RX 28
-#define U300_DMA_GENERAL_PURPOSE_0 29
-#define U300_DMA_GENERAL_PURPOSE_1 30
-#define U300_DMA_GENERAL_PURPOSE_2 31
-#define U300_DMA_GENERAL_PURPOSE_3 32
-#define U300_DMA_GENERAL_PURPOSE_4 33
-#define U300_DMA_GENERAL_PURPOSE_5 34
-#define U300_DMA_GENERAL_PURPOSE_6 35
-#define U300_DMA_GENERAL_PURPOSE_7 36
-#define U300_DMA_GENERAL_PURPOSE_8 37
-#define U300_DMA_UART1_TX 38
-#define U300_DMA_UART1_RX 39
-
-#define U300_DMA_DEVICE_CHANNELS 32
-#define U300_DMA_CHANNELS 40
-
-
-#endif /* DMA_CHANNELS_H */
diff --git a/arch/arm/mach-u300/include/mach/coh901318.h b/arch/arm/mach-u300/include/mach/coh901318.h
deleted file mode 100644
index 7c3b2b2..0000000
--- a/arch/arm/mach-u300/include/mach/coh901318.h
+++ /dev/null
@@ -1,267 +0,0 @@
-/*
- *
- * include/linux/coh901318.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- * DMA driver for COH 901 318
- * Author: Per Friden <per.friden@stericsson.com>
- */
-
-#ifndef COH901318_H
-#define COH901318_H
-
-#include <linux/device.h>
-#include <linux/dmaengine.h>
-
-#define MAX_DMA_PACKET_SIZE_SHIFT 11
-#define MAX_DMA_PACKET_SIZE (1 << MAX_DMA_PACKET_SIZE_SHIFT)
-
-/**
- * struct coh901318_lli - linked list item for DMAC
- * @control: control settings for DMAC
- * @src_addr: transfer source address
- * @dst_addr: transfer destination address
- * @link_addr: physical address to next lli
- * @virt_link_addr: virtual address of next lli (only used by pool_free)
- * @phy_this: physical address of current lli (only used by pool_free)
- */
-struct coh901318_lli {
- u32 control;
- dma_addr_t src_addr;
- dma_addr_t dst_addr;
- dma_addr_t link_addr;
-
- void *virt_link_addr;
- dma_addr_t phy_this;
-};
-/**
- * struct coh901318_params - parameters for DMAC configuration
- * @config: DMA config register
- * @ctrl_lli_last: DMA control register for the last lli in the list
- * @ctrl_lli: DMA control register for an lli
- * @ctrl_lli_chained: DMA control register for a chained lli
- */
-struct coh901318_params {
- u32 config;
- u32 ctrl_lli_last;
- u32 ctrl_lli;
- u32 ctrl_lli_chained;
-};
-/**
- * struct coh_dma_channel - dma channel base
- * @name: ascii name of dma channel
- * @number: channel id number
- * @desc_nbr_max: number of preallocated descriptors
- * @priority_high: prio of channel, 0 low otherwise high.
- * @param: configuration parameters
- * @dev_addr: physical address of periphal connected to channel
- */
-struct coh_dma_channel {
- const char name[32];
- const int number;
- const int desc_nbr_max;
- const int priority_high;
- const struct coh901318_params param;
- const dma_addr_t dev_addr;
-};
-
-/**
- * dma_access_memory_state_t - register dma for memory access
- *
- * @dev: The dma device
- * @active: 1 means dma intends to access memory
- * 0 means dma wont access memory
- */
-typedef void (*dma_access_memory_state_t)(struct device *dev,
- bool active);
-
-/**
- * struct powersave - DMA power save structure
- * @lock: lock protecting data in this struct
- * @started_channels: bit mask indicating active dma channels
- */
-struct powersave {
- spinlock_t lock;
- u64 started_channels;
-};
-/**
- * struct coh901318_platform - platform arch structure
- * @chans_slave: specifying dma slave channels
- * @chans_memcpy: specifying dma memcpy channels
- * @access_memory_state: requesting DMA memory access (on / off)
- * @chan_conf: dma channel configurations
- * @max_channels: max number of dma chanenls
- */
-struct coh901318_platform {
- const int *chans_slave;
- const int *chans_memcpy;
- const dma_access_memory_state_t access_memory_state;
- const struct coh_dma_channel *chan_conf;
- const int max_channels;
-};
-
-#ifdef CONFIG_COH901318
-/**
- * coh901318_filter_id() - DMA channel filter function
- * @chan: dma channel handle
- * @chan_id: id of dma channel to be filter out
- *
- * In dma_request_channel() it specifies what channel id to be requested
- */
-bool coh901318_filter_id(struct dma_chan *chan, void *chan_id);
-#else
-static inline bool coh901318_filter_id(struct dma_chan *chan, void *chan_id)
-{
- return false;
-}
-#endif
-
-/*
- * DMA Controller - this access the static mappings of the coh901318 dma.
- *
- */
-
-#define COH901318_MOD32_MASK (0x1F)
-#define COH901318_WORD_MASK (0xFFFFFFFF)
-/* INT_STATUS - Interrupt Status Registers 32bit (R/-) */
-#define COH901318_INT_STATUS1 (0x0000)
-#define COH901318_INT_STATUS2 (0x0004)
-/* TC_INT_STATUS - Terminal Count Interrupt Status Registers 32bit (R/-) */
-#define COH901318_TC_INT_STATUS1 (0x0008)
-#define COH901318_TC_INT_STATUS2 (0x000C)
-/* TC_INT_CLEAR - Terminal Count Interrupt Clear Registers 32bit (-/W) */
-#define COH901318_TC_INT_CLEAR1 (0x0010)
-#define COH901318_TC_INT_CLEAR2 (0x0014)
-/* RAW_TC_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
-#define COH901318_RAW_TC_INT_STATUS1 (0x0018)
-#define COH901318_RAW_TC_INT_STATUS2 (0x001C)
-/* BE_INT_STATUS - Bus Error Interrupt Status Registers 32bit (R/-) */
-#define COH901318_BE_INT_STATUS1 (0x0020)
-#define COH901318_BE_INT_STATUS2 (0x0024)
-/* BE_INT_CLEAR - Bus Error Interrupt Clear Registers 32bit (-/W) */
-#define COH901318_BE_INT_CLEAR1 (0x0028)
-#define COH901318_BE_INT_CLEAR2 (0x002C)
-/* RAW_BE_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
-#define COH901318_RAW_BE_INT_STATUS1 (0x0030)
-#define COH901318_RAW_BE_INT_STATUS2 (0x0034)
-
-/*
- * CX_CFG - Channel Configuration Registers 32bit (R/W)
- */
-#define COH901318_CX_CFG (0x0100)
-#define COH901318_CX_CFG_SPACING (0x04)
-/* Channel enable activates tha dma job */
-#define COH901318_CX_CFG_CH_ENABLE (0x00000001)
-#define COH901318_CX_CFG_CH_DISABLE (0x00000000)
-/* Request Mode */
-#define COH901318_CX_CFG_RM_MASK (0x00000006)
-#define COH901318_CX_CFG_RM_MEMORY_TO_MEMORY (0x0 << 1)
-#define COH901318_CX_CFG_RM_PRIMARY_TO_MEMORY (0x1 << 1)
-#define COH901318_CX_CFG_RM_MEMORY_TO_PRIMARY (0x1 << 1)
-#define COH901318_CX_CFG_RM_PRIMARY_TO_SECONDARY (0x3 << 1)
-#define COH901318_CX_CFG_RM_SECONDARY_TO_PRIMARY (0x3 << 1)
-/* Linked channel request field. RM must == 11 */
-#define COH901318_CX_CFG_LCRF_SHIFT 3
-#define COH901318_CX_CFG_LCRF_MASK (0x000001F8)
-#define COH901318_CX_CFG_LCR_DISABLE (0x00000000)
-/* Terminal Counter Interrupt Request Mask */
-#define COH901318_CX_CFG_TC_IRQ_ENABLE (0x00000200)
-#define COH901318_CX_CFG_TC_IRQ_DISABLE (0x00000000)
-/* Bus Error interrupt Mask */
-#define COH901318_CX_CFG_BE_IRQ_ENABLE (0x00000400)
-#define COH901318_CX_CFG_BE_IRQ_DISABLE (0x00000000)
-
-/*
- * CX_STAT - Channel Status Registers 32bit (R/-)
- */
-#define COH901318_CX_STAT (0x0200)
-#define COH901318_CX_STAT_SPACING (0x04)
-#define COH901318_CX_STAT_RBE_IRQ_IND (0x00000008)
-#define COH901318_CX_STAT_RTC_IRQ_IND (0x00000004)
-#define COH901318_CX_STAT_ACTIVE (0x00000002)
-#define COH901318_CX_STAT_ENABLED (0x00000001)
-
-/*
- * CX_CTRL - Channel Control Registers 32bit (R/W)
- */
-#define COH901318_CX_CTRL (0x0400)
-#define COH901318_CX_CTRL_SPACING (0x10)
-/* Transfer Count Enable */
-#define COH901318_CX_CTRL_TC_ENABLE (0x00001000)
-#define COH901318_CX_CTRL_TC_DISABLE (0x00000000)
-/* Transfer Count Value 0 - 4095 */
-#define COH901318_CX_CTRL_TC_VALUE_MASK (0x00000FFF)
-/* Burst count */
-#define COH901318_CX_CTRL_BURST_COUNT_MASK (0x0000E000)
-#define COH901318_CX_CTRL_BURST_COUNT_64_BYTES (0x7 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_48_BYTES (0x6 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_32_BYTES (0x5 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_16_BYTES (0x4 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_8_BYTES (0x3 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_4_BYTES (0x2 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_2_BYTES (0x1 << 13)
-#define COH901318_CX_CTRL_BURST_COUNT_1_BYTE (0x0 << 13)
-/* Source bus size */
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_MASK (0x00030000)
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS (0x2 << 16)
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS (0x1 << 16)
-#define COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS (0x0 << 16)
-/* Source address increment */
-#define COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE (0x00040000)
-#define COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE (0x00000000)
-/* Destination Bus Size */
-#define COH901318_CX_CTRL_DST_BUS_SIZE_MASK (0x00180000)
-#define COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS (0x2 << 19)
-#define COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS (0x1 << 19)
-#define COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS (0x0 << 19)
-/* Destination address increment */
-#define COH901318_CX_CTRL_DST_ADDR_INC_ENABLE (0x00200000)
-#define COH901318_CX_CTRL_DST_ADDR_INC_DISABLE (0x00000000)
-/* Master Mode (Master2 is only connected to MSL) */
-#define COH901318_CX_CTRL_MASTER_MODE_MASK (0x00C00000)
-#define COH901318_CX_CTRL_MASTER_MODE_M2R_M1W (0x3 << 22)
-#define COH901318_CX_CTRL_MASTER_MODE_M1R_M2W (0x2 << 22)
-#define COH901318_CX_CTRL_MASTER_MODE_M2RW (0x1 << 22)
-#define COH901318_CX_CTRL_MASTER_MODE_M1RW (0x0 << 22)
-/* Terminal Count flag to PER enable */
-#define COH901318_CX_CTRL_TCP_ENABLE (0x01000000)
-#define COH901318_CX_CTRL_TCP_DISABLE (0x00000000)
-/* Terminal Count flags to CPU enable */
-#define COH901318_CX_CTRL_TC_IRQ_ENABLE (0x02000000)
-#define COH901318_CX_CTRL_TC_IRQ_DISABLE (0x00000000)
-/* Hand shake to peripheral */
-#define COH901318_CX_CTRL_HSP_ENABLE (0x04000000)
-#define COH901318_CX_CTRL_HSP_DISABLE (0x00000000)
-#define COH901318_CX_CTRL_HSS_ENABLE (0x08000000)
-#define COH901318_CX_CTRL_HSS_DISABLE (0x00000000)
-/* DMA mode */
-#define COH901318_CX_CTRL_DDMA_MASK (0x30000000)
-#define COH901318_CX_CTRL_DDMA_LEGACY (0x0 << 28)
-#define COH901318_CX_CTRL_DDMA_DEMAND_DMA1 (0x1 << 28)
-#define COH901318_CX_CTRL_DDMA_DEMAND_DMA2 (0x2 << 28)
-/* Primary Request Data Destination */
-#define COH901318_CX_CTRL_PRDD_MASK (0x40000000)
-#define COH901318_CX_CTRL_PRDD_DEST (0x1 << 30)
-#define COH901318_CX_CTRL_PRDD_SOURCE (0x0 << 30)
-
-/*
- * CX_SRC_ADDR - Channel Source Address Registers 32bit (R/W)
- */
-#define COH901318_CX_SRC_ADDR (0x0404)
-#define COH901318_CX_SRC_ADDR_SPACING (0x10)
-
-/*
- * CX_DST_ADDR - Channel Destination Address Registers 32bit R/W
- */
-#define COH901318_CX_DST_ADDR (0x0408)
-#define COH901318_CX_DST_ADDR_SPACING (0x10)
-
-/*
- * CX_LNK_ADDR - Channel Link Address Registers 32bit (R/W)
- */
-#define COH901318_CX_LNK_ADDR (0x040C)
-#define COH901318_CX_LNK_ADDR_SPACING (0x10)
-#define COH901318_CX_LNK_LINK_IMMEDIATE (0x00000001)
-#endif /* COH901318_H */
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index 02e6659..9106982 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -10,9 +10,8 @@
#include <linux/amba/bus.h>
#include <linux/spi/spi.h>
#include <linux/amba/pl022.h>
+#include <linux/platform_data/dma-coh901318.h>
#include <linux/err.h>
-#include <mach/coh901318.h>
-#include "dma_channels.h"
/*
* The following is for the actual devices on the SSP/SPI bus
diff --git a/arch/arm/plat-spear/restart.c b/arch/arm/plat-spear/restart.c
index 4f99011..7d4616d5 100644
--- a/arch/arm/plat-spear/restart.c
+++ b/arch/arm/plat-spear/restart.c
@@ -11,8 +11,8 @@
* warranty of any kind, whether express or implied.
*/
#include <linux/io.h>
+#include <linux/amba/sp810.h>
#include <asm/system_misc.h>
-#include <asm/hardware/sp810.h>
#include <mach/spear.h>
#include <mach/generic.h>
diff --git a/drivers/clk/versatile/clk-vexpress.c b/drivers/clk/versatile/clk-vexpress.c
index f889f2f..82b45aa 100644
--- a/drivers/clk/versatile/clk-vexpress.c
+++ b/drivers/clk/versatile/clk-vexpress.c
@@ -11,6 +11,7 @@
* Copyright (C) 2012 ARM Limited
*/
+#include <linux/amba/sp810.h>
#include <linux/clkdev.h>
#include <linux/clk-provider.h>
#include <linux/err.h>
@@ -18,8 +19,6 @@
#include <linux/of_address.h>
#include <linux/vexpress.h>
-#include <asm/hardware/sp810.h>
-
static struct clk *vexpress_sp810_timerclken[4];
static DEFINE_SPINLOCK(vexpress_sp810_lock);
diff --git a/drivers/clocksource/nomadik-mtu.c b/drivers/clocksource/nomadik-mtu.c
index 025afc6..435e54d 100644
--- a/drivers/clocksource/nomadik-mtu.c
+++ b/drivers/clocksource/nomadik-mtu.c
@@ -15,6 +15,7 @@
#include <linux/clocksource.h>
#include <linux/clk.h>
#include <linux/jiffies.h>
+#include <linux/delay.h>
#include <linux/err.h>
#include <linux/platform_data/clocksource-nomadik-mtu.h>
#include <asm/mach/time.h>
@@ -64,6 +65,7 @@
static bool clkevt_periodic;
static u32 clk_prescale;
static u32 nmdk_cycle; /* write-once */
+static struct delay_timer mtu_delay_timer;
#ifdef CONFIG_NOMADIK_MTU_SCHED_CLOCK
/*
@@ -80,6 +82,11 @@
}
#endif
+static unsigned long nmdk_timer_read_current_timer(void)
+{
+ return ~readl_relaxed(mtu_base + MTU_VAL(0));
+}
+
/* Clockevent device: use one-shot mode */
static int nmdk_clkevt_next(unsigned long evt, struct clock_event_device *ev)
{
@@ -234,4 +241,8 @@
setup_irq(irq, &nmdk_timer_irq);
nmdk_clkevt.cpumask = cpumask_of(0);
clockevents_config_and_register(&nmdk_clkevt, rate, 2, 0xffffffffU);
+
+ mtu_delay_timer.read_current_timer = &nmdk_timer_read_current_timer;
+ mtu_delay_timer.freq = rate;
+ register_current_timer_delay(&mtu_delay_timer);
}
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 5399c45..863fd18 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -44,7 +44,7 @@
##################################################################################
# ARM SoC drivers
-obj-$(CONFIG_UX500_SOC_DB8500) += db8500-cpufreq.o
+obj-$(CONFIG_UX500_SOC_DB8500) += dbx500-cpufreq.o
obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
obj-$(CONFIG_ARM_S3C64XX_CPUFREQ) += s3c64xx-cpufreq.o
obj-$(CONFIG_ARM_S5PV210_CPUFREQ) += s5pv210-cpufreq.o
diff --git a/drivers/cpufreq/db8500-cpufreq.c b/drivers/cpufreq/dbx500-cpufreq.c
similarity index 61%
rename from drivers/cpufreq/db8500-cpufreq.c
rename to drivers/cpufreq/dbx500-cpufreq.c
index 48a1988..72f0c3e 100644
--- a/drivers/cpufreq/db8500-cpufreq.c
+++ b/drivers/cpufreq/dbx500-cpufreq.c
@@ -1,13 +1,13 @@
/*
* Copyright (C) STMicroelectronics 2009
- * Copyright (C) ST-Ericsson SA 2010
+ * Copyright (C) ST-Ericsson SA 2010-2012
*
* License Terms: GNU General Public License v2
* Author: Sundar Iyer <sundar.iyer@stericsson.com>
* Author: Martin Persson <martin.persson@stericsson.com>
* Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- *
*/
+
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/cpufreq.h>
@@ -19,22 +19,23 @@
static struct cpufreq_frequency_table *freq_table;
static struct clk *armss_clk;
-static struct freq_attr *db8500_cpufreq_attr[] = {
+static struct freq_attr *dbx500_cpufreq_attr[] = {
&cpufreq_freq_attr_scaling_available_freqs,
NULL,
};
-static int db8500_cpufreq_verify_speed(struct cpufreq_policy *policy)
+static int dbx500_cpufreq_verify_speed(struct cpufreq_policy *policy)
{
return cpufreq_frequency_table_verify(policy, freq_table);
}
-static int db8500_cpufreq_target(struct cpufreq_policy *policy,
+static int dbx500_cpufreq_target(struct cpufreq_policy *policy,
unsigned int target_freq,
unsigned int relation)
{
struct cpufreq_freqs freqs;
unsigned int idx;
+ int ret;
/* scale the target frequency to one of the extremes supported */
if (target_freq < policy->cpuinfo.min_freq)
@@ -43,10 +44,9 @@
target_freq = policy->cpuinfo.max_freq;
/* Lookup the next frequency */
- if (cpufreq_frequency_table_target
- (policy, freq_table, target_freq, relation, &idx)) {
+ if (cpufreq_frequency_table_target(policy, freq_table, target_freq,
+ relation, &idx))
return -EINVAL;
- }
freqs.old = policy->cur;
freqs.new = freq_table[idx].frequency;
@@ -59,9 +59,12 @@
cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
/* update armss clk frequency */
- if (clk_set_rate(armss_clk, freq_table[idx].frequency * 1000)) {
- pr_err("db8500-cpufreq: Failed to update armss clk\n");
- return -EINVAL;
+ ret = clk_set_rate(armss_clk, freqs.new * 1000);
+
+ if (ret) {
+ pr_err("dbx500-cpufreq: Failed to set armss_clk to %d Hz: error %d\n",
+ freqs.new * 1000, ret);
+ return ret;
}
/* post change notification */
@@ -71,7 +74,7 @@
return 0;
}
-static unsigned int db8500_cpufreq_getspeed(unsigned int cpu)
+static unsigned int dbx500_cpufreq_getspeed(unsigned int cpu)
{
int i = 0;
unsigned long freq = clk_get_rate(armss_clk) / 1000;
@@ -83,40 +86,26 @@
}
/* We could not find a corresponding frequency. */
- pr_err("db8500-cpufreq: Failed to find cpufreq speed\n");
+ pr_err("dbx500-cpufreq: Failed to find cpufreq speed\n");
return 0;
}
-static int __cpuinit db8500_cpufreq_init(struct cpufreq_policy *policy)
+static int __cpuinit dbx500_cpufreq_init(struct cpufreq_policy *policy)
{
- int i = 0;
int res;
- armss_clk = clk_get(NULL, "armss");
- if (IS_ERR(armss_clk)) {
- pr_err("db8500-cpufreq : Failed to get armss clk\n");
- return PTR_ERR(armss_clk);
- }
-
- pr_info("db8500-cpufreq : Available frequencies:\n");
- while (freq_table[i].frequency != CPUFREQ_TABLE_END) {
- pr_info(" %d Mhz\n", freq_table[i].frequency/1000);
- i++;
- }
-
/* get policy fields based on the table */
res = cpufreq_frequency_table_cpuinfo(policy, freq_table);
if (!res)
cpufreq_frequency_table_get_attr(freq_table, policy->cpu);
else {
- pr_err("db8500-cpufreq : Failed to read policy table\n");
- clk_put(armss_clk);
+ pr_err("dbx500-cpufreq: Failed to read policy table\n");
return res;
}
policy->min = policy->cpuinfo.min_freq;
policy->max = policy->cpuinfo.max_freq;
- policy->cur = db8500_cpufreq_getspeed(policy->cpu);
+ policy->cur = dbx500_cpufreq_getspeed(policy->cpu);
policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
/*
@@ -132,42 +121,54 @@
return 0;
}
-static struct cpufreq_driver db8500_cpufreq_driver = {
- .flags = CPUFREQ_STICKY,
- .verify = db8500_cpufreq_verify_speed,
- .target = db8500_cpufreq_target,
- .get = db8500_cpufreq_getspeed,
- .init = db8500_cpufreq_init,
- .name = "DB8500",
- .attr = db8500_cpufreq_attr,
+static struct cpufreq_driver dbx500_cpufreq_driver = {
+ .flags = CPUFREQ_STICKY | CPUFREQ_CONST_LOOPS,
+ .verify = dbx500_cpufreq_verify_speed,
+ .target = dbx500_cpufreq_target,
+ .get = dbx500_cpufreq_getspeed,
+ .init = dbx500_cpufreq_init,
+ .name = "DBX500",
+ .attr = dbx500_cpufreq_attr,
};
-static int db8500_cpufreq_probe(struct platform_device *pdev)
+static int dbx500_cpufreq_probe(struct platform_device *pdev)
{
- freq_table = dev_get_platdata(&pdev->dev);
+ int i = 0;
+ freq_table = dev_get_platdata(&pdev->dev);
if (!freq_table) {
- pr_err("db8500-cpufreq: Failed to fetch cpufreq table\n");
+ pr_err("dbx500-cpufreq: Failed to fetch cpufreq table\n");
return -ENODEV;
}
- return cpufreq_register_driver(&db8500_cpufreq_driver);
+ armss_clk = clk_get(&pdev->dev, "armss");
+ if (IS_ERR(armss_clk)) {
+ pr_err("dbx500-cpufreq: Failed to get armss clk\n");
+ return PTR_ERR(armss_clk);
+ }
+
+ pr_info("dbx500-cpufreq: Available frequencies:\n");
+ while (freq_table[i].frequency != CPUFREQ_TABLE_END) {
+ pr_info(" %d Mhz\n", freq_table[i].frequency/1000);
+ i++;
+ }
+
+ return cpufreq_register_driver(&dbx500_cpufreq_driver);
}
-static struct platform_driver db8500_cpufreq_plat_driver = {
+static struct platform_driver dbx500_cpufreq_plat_driver = {
.driver = {
- .name = "cpufreq-u8500",
+ .name = "cpufreq-ux500",
.owner = THIS_MODULE,
},
- .probe = db8500_cpufreq_probe,
+ .probe = dbx500_cpufreq_probe,
};
-static int __init db8500_cpufreq_register(void)
+static int __init dbx500_cpufreq_register(void)
{
- pr_info("cpufreq for DB8500 started\n");
- return platform_driver_register(&db8500_cpufreq_plat_driver);
+ return platform_driver_register(&dbx500_cpufreq_plat_driver);
}
-device_initcall(db8500_cpufreq_register);
+device_initcall(dbx500_cpufreq_register);
MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("cpufreq driver for DB8500");
+MODULE_DESCRIPTION("cpufreq driver for DBX500");
diff --git a/drivers/dma/coh901318.c b/drivers/dma/coh901318.c
index aa384e5..a2f079a 100644
--- a/drivers/dma/coh901318.c
+++ b/drivers/dma/coh901318.c
@@ -21,11 +21,1241 @@
#include <linux/io.h>
#include <linux/uaccess.h>
#include <linux/debugfs.h>
-#include <mach/coh901318.h>
+#include <linux/platform_data/dma-coh901318.h>
-#include "coh901318_lli.h"
+#include "coh901318.h"
#include "dmaengine.h"
+#define COH901318_MOD32_MASK (0x1F)
+#define COH901318_WORD_MASK (0xFFFFFFFF)
+/* INT_STATUS - Interrupt Status Registers 32bit (R/-) */
+#define COH901318_INT_STATUS1 (0x0000)
+#define COH901318_INT_STATUS2 (0x0004)
+/* TC_INT_STATUS - Terminal Count Interrupt Status Registers 32bit (R/-) */
+#define COH901318_TC_INT_STATUS1 (0x0008)
+#define COH901318_TC_INT_STATUS2 (0x000C)
+/* TC_INT_CLEAR - Terminal Count Interrupt Clear Registers 32bit (-/W) */
+#define COH901318_TC_INT_CLEAR1 (0x0010)
+#define COH901318_TC_INT_CLEAR2 (0x0014)
+/* RAW_TC_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
+#define COH901318_RAW_TC_INT_STATUS1 (0x0018)
+#define COH901318_RAW_TC_INT_STATUS2 (0x001C)
+/* BE_INT_STATUS - Bus Error Interrupt Status Registers 32bit (R/-) */
+#define COH901318_BE_INT_STATUS1 (0x0020)
+#define COH901318_BE_INT_STATUS2 (0x0024)
+/* BE_INT_CLEAR - Bus Error Interrupt Clear Registers 32bit (-/W) */
+#define COH901318_BE_INT_CLEAR1 (0x0028)
+#define COH901318_BE_INT_CLEAR2 (0x002C)
+/* RAW_BE_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */
+#define COH901318_RAW_BE_INT_STATUS1 (0x0030)
+#define COH901318_RAW_BE_INT_STATUS2 (0x0034)
+
+/*
+ * CX_CFG - Channel Configuration Registers 32bit (R/W)
+ */
+#define COH901318_CX_CFG (0x0100)
+#define COH901318_CX_CFG_SPACING (0x04)
+/* Channel enable activates tha dma job */
+#define COH901318_CX_CFG_CH_ENABLE (0x00000001)
+#define COH901318_CX_CFG_CH_DISABLE (0x00000000)
+/* Request Mode */
+#define COH901318_CX_CFG_RM_MASK (0x00000006)
+#define COH901318_CX_CFG_RM_MEMORY_TO_MEMORY (0x0 << 1)
+#define COH901318_CX_CFG_RM_PRIMARY_TO_MEMORY (0x1 << 1)
+#define COH901318_CX_CFG_RM_MEMORY_TO_PRIMARY (0x1 << 1)
+#define COH901318_CX_CFG_RM_PRIMARY_TO_SECONDARY (0x3 << 1)
+#define COH901318_CX_CFG_RM_SECONDARY_TO_PRIMARY (0x3 << 1)
+/* Linked channel request field. RM must == 11 */
+#define COH901318_CX_CFG_LCRF_SHIFT 3
+#define COH901318_CX_CFG_LCRF_MASK (0x000001F8)
+#define COH901318_CX_CFG_LCR_DISABLE (0x00000000)
+/* Terminal Counter Interrupt Request Mask */
+#define COH901318_CX_CFG_TC_IRQ_ENABLE (0x00000200)
+#define COH901318_CX_CFG_TC_IRQ_DISABLE (0x00000000)
+/* Bus Error interrupt Mask */
+#define COH901318_CX_CFG_BE_IRQ_ENABLE (0x00000400)
+#define COH901318_CX_CFG_BE_IRQ_DISABLE (0x00000000)
+
+/*
+ * CX_STAT - Channel Status Registers 32bit (R/-)
+ */
+#define COH901318_CX_STAT (0x0200)
+#define COH901318_CX_STAT_SPACING (0x04)
+#define COH901318_CX_STAT_RBE_IRQ_IND (0x00000008)
+#define COH901318_CX_STAT_RTC_IRQ_IND (0x00000004)
+#define COH901318_CX_STAT_ACTIVE (0x00000002)
+#define COH901318_CX_STAT_ENABLED (0x00000001)
+
+/*
+ * CX_CTRL - Channel Control Registers 32bit (R/W)
+ */
+#define COH901318_CX_CTRL (0x0400)
+#define COH901318_CX_CTRL_SPACING (0x10)
+/* Transfer Count Enable */
+#define COH901318_CX_CTRL_TC_ENABLE (0x00001000)
+#define COH901318_CX_CTRL_TC_DISABLE (0x00000000)
+/* Transfer Count Value 0 - 4095 */
+#define COH901318_CX_CTRL_TC_VALUE_MASK (0x00000FFF)
+/* Burst count */
+#define COH901318_CX_CTRL_BURST_COUNT_MASK (0x0000E000)
+#define COH901318_CX_CTRL_BURST_COUNT_64_BYTES (0x7 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_48_BYTES (0x6 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_32_BYTES (0x5 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_16_BYTES (0x4 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_8_BYTES (0x3 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_4_BYTES (0x2 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_2_BYTES (0x1 << 13)
+#define COH901318_CX_CTRL_BURST_COUNT_1_BYTE (0x0 << 13)
+/* Source bus size */
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_MASK (0x00030000)
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS (0x2 << 16)
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS (0x1 << 16)
+#define COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS (0x0 << 16)
+/* Source address increment */
+#define COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE (0x00040000)
+#define COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE (0x00000000)
+/* Destination Bus Size */
+#define COH901318_CX_CTRL_DST_BUS_SIZE_MASK (0x00180000)
+#define COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS (0x2 << 19)
+#define COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS (0x1 << 19)
+#define COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS (0x0 << 19)
+/* Destination address increment */
+#define COH901318_CX_CTRL_DST_ADDR_INC_ENABLE (0x00200000)
+#define COH901318_CX_CTRL_DST_ADDR_INC_DISABLE (0x00000000)
+/* Master Mode (Master2 is only connected to MSL) */
+#define COH901318_CX_CTRL_MASTER_MODE_MASK (0x00C00000)
+#define COH901318_CX_CTRL_MASTER_MODE_M2R_M1W (0x3 << 22)
+#define COH901318_CX_CTRL_MASTER_MODE_M1R_M2W (0x2 << 22)
+#define COH901318_CX_CTRL_MASTER_MODE_M2RW (0x1 << 22)
+#define COH901318_CX_CTRL_MASTER_MODE_M1RW (0x0 << 22)
+/* Terminal Count flag to PER enable */
+#define COH901318_CX_CTRL_TCP_ENABLE (0x01000000)
+#define COH901318_CX_CTRL_TCP_DISABLE (0x00000000)
+/* Terminal Count flags to CPU enable */
+#define COH901318_CX_CTRL_TC_IRQ_ENABLE (0x02000000)
+#define COH901318_CX_CTRL_TC_IRQ_DISABLE (0x00000000)
+/* Hand shake to peripheral */
+#define COH901318_CX_CTRL_HSP_ENABLE (0x04000000)
+#define COH901318_CX_CTRL_HSP_DISABLE (0x00000000)
+#define COH901318_CX_CTRL_HSS_ENABLE (0x08000000)
+#define COH901318_CX_CTRL_HSS_DISABLE (0x00000000)
+/* DMA mode */
+#define COH901318_CX_CTRL_DDMA_MASK (0x30000000)
+#define COH901318_CX_CTRL_DDMA_LEGACY (0x0 << 28)
+#define COH901318_CX_CTRL_DDMA_DEMAND_DMA1 (0x1 << 28)
+#define COH901318_CX_CTRL_DDMA_DEMAND_DMA2 (0x2 << 28)
+/* Primary Request Data Destination */
+#define COH901318_CX_CTRL_PRDD_MASK (0x40000000)
+#define COH901318_CX_CTRL_PRDD_DEST (0x1 << 30)
+#define COH901318_CX_CTRL_PRDD_SOURCE (0x0 << 30)
+
+/*
+ * CX_SRC_ADDR - Channel Source Address Registers 32bit (R/W)
+ */
+#define COH901318_CX_SRC_ADDR (0x0404)
+#define COH901318_CX_SRC_ADDR_SPACING (0x10)
+
+/*
+ * CX_DST_ADDR - Channel Destination Address Registers 32bit R/W
+ */
+#define COH901318_CX_DST_ADDR (0x0408)
+#define COH901318_CX_DST_ADDR_SPACING (0x10)
+
+/*
+ * CX_LNK_ADDR - Channel Link Address Registers 32bit (R/W)
+ */
+#define COH901318_CX_LNK_ADDR (0x040C)
+#define COH901318_CX_LNK_ADDR_SPACING (0x10)
+#define COH901318_CX_LNK_LINK_IMMEDIATE (0x00000001)
+
+/**
+ * struct coh901318_params - parameters for DMAC configuration
+ * @config: DMA config register
+ * @ctrl_lli_last: DMA control register for the last lli in the list
+ * @ctrl_lli: DMA control register for an lli
+ * @ctrl_lli_chained: DMA control register for a chained lli
+ */
+struct coh901318_params {
+ u32 config;
+ u32 ctrl_lli_last;
+ u32 ctrl_lli;
+ u32 ctrl_lli_chained;
+};
+
+/**
+ * struct coh_dma_channel - dma channel base
+ * @name: ascii name of dma channel
+ * @number: channel id number
+ * @desc_nbr_max: number of preallocated descriptors
+ * @priority_high: prio of channel, 0 low otherwise high.
+ * @param: configuration parameters
+ */
+struct coh_dma_channel {
+ const char name[32];
+ const int number;
+ const int desc_nbr_max;
+ const int priority_high;
+ const struct coh901318_params param;
+};
+
+/**
+ * struct powersave - DMA power save structure
+ * @lock: lock protecting data in this struct
+ * @started_channels: bit mask indicating active dma channels
+ */
+struct powersave {
+ spinlock_t lock;
+ u64 started_channels;
+};
+
+/* points out all dma slave channels.
+ * Syntax is [A1, B1, A2, B2, .... ,-1,-1]
+ * Select all channels from A to B, end of list is marked with -1,-1
+ */
+static int dma_slave_channels[] = {
+ U300_DMA_MSL_TX_0, U300_DMA_SPI_RX,
+ U300_DMA_UART1_TX, U300_DMA_UART1_RX, -1, -1};
+
+/* points out all dma memcpy channels. */
+static int dma_memcpy_channels[] = {
+ U300_DMA_GENERAL_PURPOSE_0, U300_DMA_GENERAL_PURPOSE_8, -1, -1};
+
+#define flags_memcpy_config (COH901318_CX_CFG_CH_DISABLE | \
+ COH901318_CX_CFG_RM_MEMORY_TO_MEMORY | \
+ COH901318_CX_CFG_LCR_DISABLE | \
+ COH901318_CX_CFG_TC_IRQ_ENABLE | \
+ COH901318_CX_CFG_BE_IRQ_ENABLE)
+#define flags_memcpy_lli_chained (COH901318_CX_CTRL_TC_ENABLE | \
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
+ COH901318_CX_CTRL_MASTER_MODE_M1RW | \
+ COH901318_CX_CTRL_TCP_DISABLE | \
+ COH901318_CX_CTRL_TC_IRQ_DISABLE | \
+ COH901318_CX_CTRL_HSP_DISABLE | \
+ COH901318_CX_CTRL_HSS_DISABLE | \
+ COH901318_CX_CTRL_DDMA_LEGACY | \
+ COH901318_CX_CTRL_PRDD_SOURCE)
+#define flags_memcpy_lli (COH901318_CX_CTRL_TC_ENABLE | \
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
+ COH901318_CX_CTRL_MASTER_MODE_M1RW | \
+ COH901318_CX_CTRL_TCP_DISABLE | \
+ COH901318_CX_CTRL_TC_IRQ_DISABLE | \
+ COH901318_CX_CTRL_HSP_DISABLE | \
+ COH901318_CX_CTRL_HSS_DISABLE | \
+ COH901318_CX_CTRL_DDMA_LEGACY | \
+ COH901318_CX_CTRL_PRDD_SOURCE)
+#define flags_memcpy_lli_last (COH901318_CX_CTRL_TC_ENABLE | \
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \
+ COH901318_CX_CTRL_MASTER_MODE_M1RW | \
+ COH901318_CX_CTRL_TCP_DISABLE | \
+ COH901318_CX_CTRL_TC_IRQ_ENABLE | \
+ COH901318_CX_CTRL_HSP_DISABLE | \
+ COH901318_CX_CTRL_HSS_DISABLE | \
+ COH901318_CX_CTRL_DDMA_LEGACY | \
+ COH901318_CX_CTRL_PRDD_SOURCE)
+
+const struct coh_dma_channel chan_config[U300_DMA_CHANNELS] = {
+ {
+ .number = U300_DMA_MSL_TX_0,
+ .name = "MSL TX 0",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_MSL_TX_1,
+ .name = "MSL TX 1",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ },
+ {
+ .number = U300_DMA_MSL_TX_2,
+ .name = "MSL TX 2",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .desc_nbr_max = 10,
+ },
+ {
+ .number = U300_DMA_MSL_TX_3,
+ .name = "MSL TX 3",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ },
+ {
+ .number = U300_DMA_MSL_TX_4,
+ .name = "MSL TX 4",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1R_M2W |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ },
+ {
+ .number = U300_DMA_MSL_TX_5,
+ .name = "MSL TX 5",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_MSL_TX_6,
+ .name = "MSL TX 6",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_MSL_RX_0,
+ .name = "MSL RX 0",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_MSL_RX_1,
+ .name = "MSL RX 1",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_MSL_RX_2,
+ .name = "MSL RX 2",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_MSL_RX_3,
+ .name = "MSL RX 3",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_MSL_RX_4,
+ .name = "MSL RX 4",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_MSL_RX_5,
+ .name = "MSL RX 5",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_32_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M2R_M1W |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_DEMAND_DMA1 |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_MSL_RX_6,
+ .name = "MSL RX 6",
+ .priority_high = 0,
+ },
+ /*
+ * Don't set up device address, burst count or size of src
+ * or dst bus for this peripheral - handled by PrimeCell
+ * DMA extension.
+ */
+ {
+ .number = U300_DMA_MMCSD_RX_TX,
+ .name = "MMCSD RX TX",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+
+ },
+ {
+ .number = U300_DMA_MSPRO_TX,
+ .name = "MSPRO TX",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_MSPRO_RX,
+ .name = "MSPRO RX",
+ .priority_high = 0,
+ },
+ /*
+ * Don't set up device address, burst count or size of src
+ * or dst bus for this peripheral - handled by PrimeCell
+ * DMA extension.
+ */
+ {
+ .number = U300_DMA_UART0_TX,
+ .name = "UART0 TX",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ },
+ {
+ .number = U300_DMA_UART0_RX,
+ .name = "UART0 RX",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ },
+ {
+ .number = U300_DMA_APEX_TX,
+ .name = "APEX TX",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_APEX_RX,
+ .name = "APEX RX",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_PCM_I2S0_TX,
+ .name = "PCM I2S0 TX",
+ .priority_high = 1,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ },
+ {
+ .number = U300_DMA_PCM_I2S0_RX,
+ .name = "PCM I2S0 RX",
+ .priority_high = 1,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_PCM_I2S1_TX,
+ .name = "PCM I2S1 TX",
+ .priority_high = 1,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_SOURCE,
+ },
+ {
+ .number = U300_DMA_PCM_I2S1_RX,
+ .name = "PCM I2S1 RX",
+ .priority_high = 1,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_DEST,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_BURST_COUNT_16_BYTES |
+ COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE |
+ COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS |
+ COH901318_CX_CTRL_DST_ADDR_INC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_ENABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY |
+ COH901318_CX_CTRL_PRDD_DEST,
+ },
+ {
+ .number = U300_DMA_XGAM_CDI,
+ .name = "XGAM CDI",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_XGAM_PDI,
+ .name = "XGAM PDI",
+ .priority_high = 0,
+ },
+ /*
+ * Don't set up device address, burst count or size of src
+ * or dst bus for this peripheral - handled by PrimeCell
+ * DMA extension.
+ */
+ {
+ .number = U300_DMA_SPI_TX,
+ .name = "SPI TX",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ },
+ {
+ .number = U300_DMA_SPI_RX,
+ .name = "SPI RX",
+ .priority_high = 0,
+ .param.config = COH901318_CX_CFG_CH_DISABLE |
+ COH901318_CX_CFG_LCR_DISABLE |
+ COH901318_CX_CFG_TC_IRQ_ENABLE |
+ COH901318_CX_CFG_BE_IRQ_ENABLE,
+ .param.ctrl_lli_chained = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_DISABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+ .param.ctrl_lli_last = 0 |
+ COH901318_CX_CTRL_TC_ENABLE |
+ COH901318_CX_CTRL_MASTER_MODE_M1RW |
+ COH901318_CX_CTRL_TCP_DISABLE |
+ COH901318_CX_CTRL_TC_IRQ_ENABLE |
+ COH901318_CX_CTRL_HSP_ENABLE |
+ COH901318_CX_CTRL_HSS_DISABLE |
+ COH901318_CX_CTRL_DDMA_LEGACY,
+
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_0,
+ .name = "GENERAL 00",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_1,
+ .name = "GENERAL 01",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_2,
+ .name = "GENERAL 02",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_3,
+ .name = "GENERAL 03",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_4,
+ .name = "GENERAL 04",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_5,
+ .name = "GENERAL 05",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_6,
+ .name = "GENERAL 06",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_7,
+ .name = "GENERAL 07",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_GENERAL_PURPOSE_8,
+ .name = "GENERAL 08",
+ .priority_high = 0,
+
+ .param.config = flags_memcpy_config,
+ .param.ctrl_lli_chained = flags_memcpy_lli_chained,
+ .param.ctrl_lli = flags_memcpy_lli,
+ .param.ctrl_lli_last = flags_memcpy_lli_last,
+ },
+ {
+ .number = U300_DMA_UART1_TX,
+ .name = "UART1 TX",
+ .priority_high = 0,
+ },
+ {
+ .number = U300_DMA_UART1_RX,
+ .name = "UART1 RX",
+ .priority_high = 0,
+ }
+};
+
#define COHC_2_DEV(cohc) (&cohc->chan.dev->device)
#ifdef VERBOSE_DEBUG
@@ -54,7 +1284,6 @@
struct dma_device dma_slave;
struct dma_device dma_memcpy;
struct coh901318_chan *chans;
- struct coh901318_platform *platform;
};
struct coh901318_chan {
@@ -75,8 +1304,8 @@
unsigned long nbr_active_done;
unsigned long busy;
- u32 runtime_addr;
- u32 runtime_ctrl;
+ u32 addr;
+ u32 ctrl;
struct coh901318_base *base;
};
@@ -122,7 +1351,7 @@
tmp += sprintf(tmp, "DMA -- enabled dma channels\n");
- for (i = 0; i < debugfs_dma_base->platform->max_channels; i++)
+ for (i = 0; i < U300_DMA_CHANNELS; i++)
if (started_channels & (1 << i))
tmp += sprintf(tmp, "channel %d\n", i);
@@ -187,25 +1416,16 @@
return container_of(chan, struct coh901318_chan, chan);
}
-static inline dma_addr_t
-cohc_dev_addr(struct coh901318_chan *cohc)
-{
- /* Runtime supplied address will take precedence */
- if (cohc->runtime_addr)
- return cohc->runtime_addr;
- return cohc->base->platform->chan_conf[cohc->id].dev_addr;
-}
-
static inline const struct coh901318_params *
cohc_chan_param(struct coh901318_chan *cohc)
{
- return &cohc->base->platform->chan_conf[cohc->id].param;
+ return &chan_config[cohc->id].param;
}
static inline const struct coh_dma_channel *
cohc_chan_conf(struct coh901318_chan *cohc)
{
- return &cohc->base->platform->chan_conf[cohc->id];
+ return &chan_config[cohc->id];
}
static void enable_powersave(struct coh901318_chan *cohc)
@@ -217,12 +1437,6 @@
pm->started_channels &= ~(1ULL << cohc->id);
- if (!pm->started_channels) {
- /* DMA no longer intends to access memory */
- cohc->base->platform->access_memory_state(cohc->base->dev,
- false);
- }
-
spin_unlock_irqrestore(&pm->lock, flags);
}
static void disable_powersave(struct coh901318_chan *cohc)
@@ -232,12 +1446,6 @@
spin_lock_irqsave(&pm->lock, flags);
- if (!pm->started_channels) {
- /* DMA intends to access memory */
- cohc->base->platform->access_memory_state(cohc->base->dev,
- true);
- }
-
pm->started_channels |= (1ULL << cohc->id);
spin_unlock_irqrestore(&pm->lock, flags);
@@ -596,7 +1804,7 @@
if (param)
p = param;
else
- p = &cohc->base->platform->chan_conf[channel].param;
+ p = cohc_chan_param(cohc);
/* Clear any pending BE or TC interrupt */
if (channel < 32) {
@@ -1052,9 +2260,9 @@
* sure the bits you set per peripheral channel are
* cleared in the default config from the platform.
*/
- ctrl_chained |= cohc->runtime_ctrl;
- ctrl_last |= cohc->runtime_ctrl;
- ctrl |= cohc->runtime_ctrl;
+ ctrl_chained |= cohc->ctrl;
+ ctrl_last |= cohc->ctrl;
+ ctrl |= cohc->ctrl;
if (direction == DMA_MEM_TO_DEV) {
u32 tx_flags = COH901318_CX_CTRL_PRDD_SOURCE |
@@ -1103,7 +2311,7 @@
/* initiate allocated lli list */
ret = coh901318_lli_fill_sg(&cohc->base->pool, lli, sgl, sg_len,
- cohc_dev_addr(cohc),
+ cohc->addr,
ctrl_chained,
ctrl,
ctrl_last,
@@ -1244,7 +2452,7 @@
dma_addr_t addr;
enum dma_slave_buswidth addr_width;
u32 maxburst;
- u32 runtime_ctrl = 0;
+ u32 ctrl = 0;
int i = 0;
/* We only support mem to per or per to mem transfers */
@@ -1265,7 +2473,7 @@
addr_width);
switch (addr_width) {
case DMA_SLAVE_BUSWIDTH_1_BYTE:
- runtime_ctrl |=
+ ctrl |=
COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS |
COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS;
@@ -1277,7 +2485,7 @@
break;
case DMA_SLAVE_BUSWIDTH_2_BYTES:
- runtime_ctrl |=
+ ctrl |=
COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS |
COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS;
@@ -1290,7 +2498,7 @@
break;
case DMA_SLAVE_BUSWIDTH_4_BYTES:
/* Direction doesn't matter here, it's 32/32 bits */
- runtime_ctrl |=
+ ctrl |=
COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS |
COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS;
@@ -1307,13 +2515,13 @@
return;
}
- runtime_ctrl |= burst_sizes[i].reg;
+ ctrl |= burst_sizes[i].reg;
dev_dbg(COHC_2_DEV(cohc),
"selected burst size %d bytes for address width %d bytes, maxburst %d\n",
burst_sizes[i].burst_8bit, addr_width, maxburst);
- cohc->runtime_addr = addr;
- cohc->runtime_ctrl = runtime_ctrl;
+ cohc->addr = addr;
+ cohc->ctrl = ctrl;
}
static int
@@ -1431,7 +2639,6 @@
static int __init coh901318_probe(struct platform_device *pdev)
{
int err = 0;
- struct coh901318_platform *pdata;
struct coh901318_base *base;
int irq;
struct resource *io;
@@ -1447,13 +2654,9 @@
pdev->dev.driver->name) == NULL)
return -ENOMEM;
- pdata = pdev->dev.platform_data;
- if (!pdata)
- return -ENODEV;
-
base = devm_kzalloc(&pdev->dev,
ALIGN(sizeof(struct coh901318_base), 4) +
- pdata->max_channels *
+ U300_DMA_CHANNELS *
sizeof(struct coh901318_chan),
GFP_KERNEL);
if (!base)
@@ -1466,7 +2669,6 @@
return -ENOMEM;
base->dev = &pdev->dev;
- base->platform = pdata;
spin_lock_init(&base->pm.lock);
base->pm.started_channels = 0;
@@ -1488,7 +2690,7 @@
return err;
/* init channels for device transfers */
- coh901318_base_init(&base->dma_slave, base->platform->chans_slave,
+ coh901318_base_init(&base->dma_slave, dma_slave_channels,
base);
dma_cap_zero(base->dma_slave.cap_mask);
@@ -1508,7 +2710,7 @@
goto err_register_slave;
/* init channels for memcpy */
- coh901318_base_init(&base->dma_memcpy, base->platform->chans_memcpy,
+ coh901318_base_init(&base->dma_memcpy, dma_memcpy_channels,
base);
dma_cap_zero(base->dma_memcpy.cap_mask);
diff --git a/drivers/dma/coh901318_lli.h b/drivers/dma/coh901318.h
similarity index 80%
rename from drivers/dma/coh901318_lli.h
rename to drivers/dma/coh901318.h
index abff371..95ce1e2 100644
--- a/drivers/dma/coh901318_lli.h
+++ b/drivers/dma/coh901318.h
@@ -1,16 +1,15 @@
/*
- * driver/dma/coh901318_lli.h
- *
- * Copyright (C) 2007-2009 ST-Ericsson
+ * Copyright (C) 2007-2013 ST-Ericsson
* License terms: GNU General Public License (GPL) version 2
- * Support functions for handling lli for coh901318
+ * DMA driver for COH 901 318
* Author: Per Friden <per.friden@stericsson.com>
*/
-#ifndef COH901318_LLI_H
-#define COH901318_LLI_H
+#ifndef COH901318_H
+#define COH901318_H
-#include <mach/coh901318.h>
+#define MAX_DMA_PACKET_SIZE_SHIFT 11
+#define MAX_DMA_PACKET_SIZE (1 << MAX_DMA_PACKET_SIZE_SHIFT)
struct device;
@@ -24,7 +23,25 @@
#endif
};
-struct device;
+/**
+ * struct coh901318_lli - linked list item for DMAC
+ * @control: control settings for DMAC
+ * @src_addr: transfer source address
+ * @dst_addr: transfer destination address
+ * @link_addr: physical address to next lli
+ * @virt_link_addr: virtual address of next lli (only used by pool_free)
+ * @phy_this: physical address of current lli (only used by pool_free)
+ */
+struct coh901318_lli {
+ u32 control;
+ dma_addr_t src_addr;
+ dma_addr_t dst_addr;
+ dma_addr_t link_addr;
+
+ void *virt_link_addr;
+ dma_addr_t phy_this;
+};
+
/**
* coh901318_pool_create() - Creates an dma pool for lli:s
* @pool: pool handle
@@ -121,4 +138,4 @@
u32 ctrl, u32 ctrl_last,
enum dma_transfer_direction dir, u32 ctrl_irq_mask);
-#endif /* COH901318_LLI_H */
+#endif /* COH901318_H */
diff --git a/drivers/dma/coh901318_lli.c b/drivers/dma/coh901318_lli.c
index 780e042..3e96610 100644
--- a/drivers/dma/coh901318_lli.c
+++ b/drivers/dma/coh901318_lli.c
@@ -11,9 +11,9 @@
#include <linux/memory.h>
#include <linux/gfp.h>
#include <linux/dmapool.h>
-#include <mach/coh901318.h>
+#include <linux/dmaengine.h>
-#include "coh901318_lli.h"
+#include "coh901318.h"
#if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG))
#define DEBUGFS_POOL_COUNTER_RESET(pool) (pool->debugfs_pool_counter = 0)
diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 1192518e..a2bacf9 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -3102,8 +3102,8 @@
.pdata_size = sizeof(db8500_regulators),
},
{
- .name = "cpufreq-u8500",
- .of_compatible = "stericsson,cpufreq-u8500",
+ .name = "cpufreq-ux500",
+ .of_compatible = "stericsson,cpufreq-ux500",
.platform_data = &db8500_cpufreq_table,
.pdata_size = sizeof(db8500_cpufreq_table),
},
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 0002d5e..1d333497c 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -1332,6 +1332,7 @@
dma_cap_mask_t mask;
unsigned sig;
struct resource *res;
+ struct mtd_part_parser_data ppdata = {};
pdata = pdev->dev.platform_data;
if (pdata == NULL) {
@@ -1557,7 +1558,8 @@
goto out_release_mem_region;
}
- mtd_device_parse_register(&info->mtd, NULL, NULL, pdata->parts,
+ ppdata.of_node = pdata->of_node;
+ mtd_device_parse_register(&info->mtd, NULL, &ppdata, pdata->parts,
pdata->nr_parts);
platform_set_drvdata(pdev, &info->mtd);
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index 065f3fe..eec2aed 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -637,6 +637,7 @@
struct onenand_chip *this;
int r;
struct resource *res;
+ struct mtd_part_parser_data ppdata = {};
pdata = pdev->dev.platform_data;
if (pdata == NULL) {
@@ -767,7 +768,8 @@
if ((r = onenand_scan(&c->mtd, 1)) < 0)
goto err_release_regulator;
- r = mtd_device_parse_register(&c->mtd, NULL, NULL,
+ ppdata.of_node = pdata->of_node;
+ r = mtd_device_parse_register(&c->mtd, NULL, &ppdata,
pdata ? pdata->parts : NULL,
pdata ? pdata->nr_parts : 0);
if (r)
diff --git a/arch/arm/include/asm/hardware/sp810.h b/include/linux/amba/sp810.h
similarity index 100%
rename from arch/arm/include/asm/hardware/sp810.h
rename to include/linux/amba/sp810.h
diff --git a/include/linux/platform_data/dma-coh901318.h b/include/linux/platform_data/dma-coh901318.h
new file mode 100644
index 0000000..c4cb959
--- /dev/null
+++ b/include/linux/platform_data/dma-coh901318.h
@@ -0,0 +1,72 @@
+/*
+ * Platform data for the COH901318 DMA controller
+ * Copyright (C) 2007-2013 ST-Ericsson
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef PLAT_COH901318_H
+#define PLAT_COH901318_H
+
+#ifdef CONFIG_COH901318
+
+/* We only support the U300 DMA channels */
+#define U300_DMA_MSL_TX_0 0
+#define U300_DMA_MSL_TX_1 1
+#define U300_DMA_MSL_TX_2 2
+#define U300_DMA_MSL_TX_3 3
+#define U300_DMA_MSL_TX_4 4
+#define U300_DMA_MSL_TX_5 5
+#define U300_DMA_MSL_TX_6 6
+#define U300_DMA_MSL_RX_0 7
+#define U300_DMA_MSL_RX_1 8
+#define U300_DMA_MSL_RX_2 9
+#define U300_DMA_MSL_RX_3 10
+#define U300_DMA_MSL_RX_4 11
+#define U300_DMA_MSL_RX_5 12
+#define U300_DMA_MSL_RX_6 13
+#define U300_DMA_MMCSD_RX_TX 14
+#define U300_DMA_MSPRO_TX 15
+#define U300_DMA_MSPRO_RX 16
+#define U300_DMA_UART0_TX 17
+#define U300_DMA_UART0_RX 18
+#define U300_DMA_APEX_TX 19
+#define U300_DMA_APEX_RX 20
+#define U300_DMA_PCM_I2S0_TX 21
+#define U300_DMA_PCM_I2S0_RX 22
+#define U300_DMA_PCM_I2S1_TX 23
+#define U300_DMA_PCM_I2S1_RX 24
+#define U300_DMA_XGAM_CDI 25
+#define U300_DMA_XGAM_PDI 26
+#define U300_DMA_SPI_TX 27
+#define U300_DMA_SPI_RX 28
+#define U300_DMA_GENERAL_PURPOSE_0 29
+#define U300_DMA_GENERAL_PURPOSE_1 30
+#define U300_DMA_GENERAL_PURPOSE_2 31
+#define U300_DMA_GENERAL_PURPOSE_3 32
+#define U300_DMA_GENERAL_PURPOSE_4 33
+#define U300_DMA_GENERAL_PURPOSE_5 34
+#define U300_DMA_GENERAL_PURPOSE_6 35
+#define U300_DMA_GENERAL_PURPOSE_7 36
+#define U300_DMA_GENERAL_PURPOSE_8 37
+#define U300_DMA_UART1_TX 38
+#define U300_DMA_UART1_RX 39
+
+#define U300_DMA_DEVICE_CHANNELS 32
+#define U300_DMA_CHANNELS 40
+
+/**
+ * coh901318_filter_id() - DMA channel filter function
+ * @chan: dma channel handle
+ * @chan_id: id of dma channel to be filter out
+ *
+ * In dma_request_channel() it specifies what channel id to be requested
+ */
+bool coh901318_filter_id(struct dma_chan *chan, void *chan_id);
+#else
+static inline bool coh901318_filter_id(struct dma_chan *chan, void *chan_id)
+{
+ return false;
+}
+#endif
+
+#endif /* PLAT_COH901318_H */
diff --git a/include/linux/platform_data/mtd-nand-omap2.h b/include/linux/platform_data/mtd-nand-omap2.h
index 24d32ca..6bf9ef4 100644
--- a/include/linux/platform_data/mtd-nand-omap2.h
+++ b/include/linux/platform_data/mtd-nand-omap2.h
@@ -60,6 +60,8 @@
int devsize;
enum omap_ecc ecc_opt;
struct gpmc_nand_regs reg;
-};
+ /* for passing the partitions */
+ struct device_node *of_node;
+};
#endif
diff --git a/include/linux/platform_data/mtd-onenand-omap2.h b/include/linux/platform_data/mtd-onenand-omap2.h
index 685af7e..e9a9fb1 100644
--- a/include/linux/platform_data/mtd-onenand-omap2.h
+++ b/include/linux/platform_data/mtd-onenand-omap2.h
@@ -29,5 +29,8 @@
u8 flags;
u8 regulator_can_sleep;
u8 skip_initial_unlocking;
+
+ /* for passing the partitions */
+ struct device_node *of_node;
};
#endif
