// SPDX-License-Identifier: GPL-2.0+
/*
 * dmm32at.c
 * Diamond Systems Diamond-MM-32-AT Comedi driver
 *
 * COMEDI - Linux Control and Measurement Device Interface
 * Copyright (C) 2000 David A. Schleef <ds@schleef.org>
 */

/*
 * Driver: dmm32at
 * Description: Diamond Systems Diamond-MM-32-AT
 * Devices: [Diamond Systems] Diamond-MM-32-AT (dmm32at)
 * Author: Perry J. Piplani <perry.j.piplani@nasa.gov>
 * Updated: Fri Jun  4 09:13:24 CDT 2004
 * Status: experimental
 *
 * Configuration Options:
 *	comedi_config /dev/comedi0 dmm32at baseaddr,irq
 *
 * This driver is for the Diamond Systems MM-32-AT board
 *	http://www.diamondsystems.com/products/diamondmm32at
 *
 * It is being used on several projects inside NASA, without
 * problems so far. For analog input commands, TRIG_EXT is not
 * yet supported.
 */

#include <linux/module.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include "../comedidev.h"

#include "8255.h"

/* Board register addresses */
#define DMM32AT_AI_START_CONV_REG	0x00
#define DMM32AT_AI_LSB_REG		0x00
#define DMM32AT_AUX_DOUT_REG		0x01
#define DMM32AT_AUX_DOUT2		BIT(2)  /* J3.42 - OUT2 (OUT2EN) */
#define DMM32AT_AUX_DOUT1		BIT(1)  /* J3.43 */
#define DMM32AT_AUX_DOUT0		BIT(0)  /* J3.44 - OUT0 (OUT0EN) */
#define DMM32AT_AI_MSB_REG		0x01
#define DMM32AT_AI_LO_CHAN_REG		0x02
#define DMM32AT_AI_HI_CHAN_REG		0x03
#define DMM32AT_AUX_DI_REG		0x04
#define DMM32AT_AUX_DI_DACBUSY		BIT(7)
#define DMM32AT_AUX_DI_CALBUSY		BIT(6)
#define DMM32AT_AUX_DI3			BIT(3)  /* J3.45 - ADCLK (CLKSEL) */
#define DMM32AT_AUX_DI2			BIT(2)  /* J3.46 - GATE12 (GT12EN) */
#define DMM32AT_AUX_DI1			BIT(1)  /* J3.47 - GATE0 (GT0EN) */
#define DMM32AT_AUX_DI0			BIT(0)  /* J3.48 - CLK0 (SRC0) */
#define DMM32AT_AO_LSB_REG		0x04
#define DMM32AT_AO_MSB_REG		0x05
#define DMM32AT_AO_MSB_DACH(x)		((x) << 6)
#define DMM32AT_FIFO_DEPTH_REG		0x06
#define DMM32AT_FIFO_CTRL_REG		0x07
#define DMM32AT_FIFO_CTRL_FIFOEN	BIT(3)
#define DMM32AT_FIFO_CTRL_SCANEN	BIT(2)
#define DMM32AT_FIFO_CTRL_FIFORST	BIT(1)
#define DMM32AT_FIFO_STATUS_REG		0x07
#define DMM32AT_FIFO_STATUS_EF		BIT(7)
#define DMM32AT_FIFO_STATUS_HF		BIT(6)
#define DMM32AT_FIFO_STATUS_FF		BIT(5)
#define DMM32AT_FIFO_STATUS_OVF		BIT(4)
#define DMM32AT_FIFO_STATUS_FIFOEN	BIT(3)
#define DMM32AT_FIFO_STATUS_SCANEN	BIT(2)
#define DMM32AT_FIFO_STATUS_PAGE_MASK	(3 << 0)
#define DMM32AT_CTRL_REG		0x08
#define DMM32AT_CTRL_RESETA		BIT(5)
#define DMM32AT_CTRL_RESETD		BIT(4)
#define DMM32AT_CTRL_INTRST		BIT(3)
#define DMM32AT_CTRL_PAGE(x)		((x) << 0)
#define DMM32AT_CTRL_PAGE_8254		DMM32AT_CTRL_PAGE(0)
#define DMM32AT_CTRL_PAGE_8255		DMM32AT_CTRL_PAGE(1)
#define DMM32AT_CTRL_PAGE_CALIB		DMM32AT_CTRL_PAGE(3)
#define DMM32AT_AI_STATUS_REG		0x08
#define DMM32AT_AI_STATUS_STS		BIT(7)
#define DMM32AT_AI_STATUS_SD1		BIT(6)
#define DMM32AT_AI_STATUS_SD0		BIT(5)
#define DMM32AT_AI_STATUS_ADCH_MASK	(0x1f << 0)
#define DMM32AT_INTCLK_REG		0x09
#define DMM32AT_INTCLK_ADINT		BIT(7)
#define DMM32AT_INTCLK_DINT		BIT(6)
#define DMM32AT_INTCLK_TINT		BIT(5)
#define DMM32AT_INTCLK_CLKEN		BIT(1)  /* 1=see below  0=software */
#define DMM32AT_INTCLK_CLKSEL		BIT(0)  /* 1=OUT2  0=EXTCLK */
#define DMM32AT_CTRDIO_CFG_REG		0x0a
#define DMM32AT_CTRDIO_CFG_FREQ12	BIT(7)  /* CLK12 1=100KHz 0=10MHz */
#define DMM32AT_CTRDIO_CFG_FREQ0	BIT(6)  /* CLK0  1=10KHz  0=10MHz */
#define DMM32AT_CTRDIO_CFG_OUT2EN	BIT(5)  /* J3.42 1=OUT2 is DOUT2 */
#define DMM32AT_CTRDIO_CFG_OUT0EN	BIT(4)  /* J3,44 1=OUT0 is DOUT0 */
#define DMM32AT_CTRDIO_CFG_GT0EN	BIT(2)  /* J3.47 1=DIN1 is GATE0 */
#define DMM32AT_CTRDIO_CFG_SRC0		BIT(1)  /* CLK0 is 0=FREQ0 1=J3.48 */
#define DMM32AT_CTRDIO_CFG_GT12EN	BIT(0)  /* J3.46 1=DIN2 is GATE12 */
#define DMM32AT_AI_CFG_REG		0x0b
#define DMM32AT_AI_CFG_SCINT(x)		((x) << 4)
#define DMM32AT_AI_CFG_SCINT_20US	DMM32AT_AI_CFG_SCINT(0)
#define DMM32AT_AI_CFG_SCINT_15US	DMM32AT_AI_CFG_SCINT(1)
#define DMM32AT_AI_CFG_SCINT_10US	DMM32AT_AI_CFG_SCINT(2)
#define DMM32AT_AI_CFG_SCINT_5US	DMM32AT_AI_CFG_SCINT(3)
#define DMM32AT_AI_CFG_RANGE		BIT(3)  /* 0=5V  1=10V */
#define DMM32AT_AI_CFG_ADBU		BIT(2)  /* 0=bipolar  1=unipolar */
#define DMM32AT_AI_CFG_GAIN(x)		((x) << 0)
#define DMM32AT_AI_READBACK_REG		0x0b
#define DMM32AT_AI_READBACK_WAIT	BIT(7)  /* DMM32AT_AI_STATUS_STS */
#define DMM32AT_AI_READBACK_RANGE	BIT(3)
#define DMM32AT_AI_READBACK_ADBU	BIT(2)
#define DMM32AT_AI_READBACK_GAIN_MASK	(3 << 0)

#define DMM32AT_CLK1 0x0d
#define DMM32AT_CLK2 0x0e
#define DMM32AT_CLKCT 0x0f

#define DMM32AT_8255_IOBASE		0x0c  /* Page 1 registers */

/* Board register values. */

/* DMM32AT_AI_CFG_REG 0x0b */
#define DMM32AT_RANGE_U10 0x0c
#define DMM32AT_RANGE_U5 0x0d
#define DMM32AT_RANGE_B10 0x08
#define DMM32AT_RANGE_B5 0x00

/* DMM32AT_CLKCT 0x0f */
#define DMM32AT_CLKCT1 0x56	/* mode3 counter 1 - write low byte only */
#define DMM32AT_CLKCT2 0xb6	/*  mode3 counter 2 - write high and low byte */

/* board AI ranges in comedi structure */
static const struct comedi_lrange dmm32at_airanges = {
	4, {
		UNI_RANGE(10),
		UNI_RANGE(5),
		BIP_RANGE(10),
		BIP_RANGE(5)
	}
};

/* register values for above ranges */
static const unsigned char dmm32at_rangebits[] = {
	DMM32AT_RANGE_U10,
	DMM32AT_RANGE_U5,
	DMM32AT_RANGE_B10,
	DMM32AT_RANGE_B5,
};

/* only one of these ranges is valid, as set by a jumper on the
 * board. The application should only use the range set by the jumper
 */
static const struct comedi_lrange dmm32at_aoranges = {
	4, {
		UNI_RANGE(10),
		UNI_RANGE(5),
		BIP_RANGE(10),
		BIP_RANGE(5)
	}
};

static void dmm32at_ai_set_chanspec(struct comedi_device *dev,
				    struct comedi_subdevice *s,
				    unsigned int chanspec, int nchan)
{
	unsigned int chan = CR_CHAN(chanspec);
	unsigned int range = CR_RANGE(chanspec);
	unsigned int last_chan = (chan + nchan - 1) % s->n_chan;

	outb(DMM32AT_FIFO_CTRL_FIFORST, dev->iobase + DMM32AT_FIFO_CTRL_REG);

	if (nchan > 1)
		outb(DMM32AT_FIFO_CTRL_SCANEN,
		     dev->iobase + DMM32AT_FIFO_CTRL_REG);

	outb(chan, dev->iobase + DMM32AT_AI_LO_CHAN_REG);
	outb(last_chan, dev->iobase + DMM32AT_AI_HI_CHAN_REG);
	outb(dmm32at_rangebits[range], dev->iobase + DMM32AT_AI_CFG_REG);
}

static unsigned int dmm32at_ai_get_sample(struct comedi_device *dev,
					  struct comedi_subdevice *s)
{
	unsigned int val;

	val = inb(dev->iobase + DMM32AT_AI_LSB_REG);
	val |= (inb(dev->iobase + DMM32AT_AI_MSB_REG) << 8);

	/* munge two's complement value to offset binary */
	return comedi_offset_munge(s, val);
}

static int dmm32at_ai_status(struct comedi_device *dev,
			     struct comedi_subdevice *s,
			     struct comedi_insn *insn,
			     unsigned long context)
{
	unsigned char status;

	status = inb(dev->iobase + context);
	if ((status & DMM32AT_AI_STATUS_STS) == 0)
		return 0;
	return -EBUSY;
}

static int dmm32at_ai_insn_read(struct comedi_device *dev,
				struct comedi_subdevice *s,
				struct comedi_insn *insn,
				unsigned int *data)
{
	int ret;
	int i;

	dmm32at_ai_set_chanspec(dev, s, insn->chanspec, 1);

	/* wait for circuit to settle */
	ret = comedi_timeout(dev, s, insn, dmm32at_ai_status,
			     DMM32AT_AI_READBACK_REG);
	if (ret)
		return ret;

	for (i = 0; i < insn->n; i++) {
		outb(0xff, dev->iobase + DMM32AT_AI_START_CONV_REG);

		ret = comedi_timeout(dev, s, insn, dmm32at_ai_status,
				     DMM32AT_AI_STATUS_REG);
		if (ret)
			return ret;

		data[i] = dmm32at_ai_get_sample(dev, s);
	}

	return insn->n;
}

static int dmm32at_ai_check_chanlist(struct comedi_device *dev,
				     struct comedi_subdevice *s,
				     struct comedi_cmd *cmd)
{
	unsigned int chan0 = CR_CHAN(cmd->chanlist[0]);
	unsigned int range0 = CR_RANGE(cmd->chanlist[0]);
	int i;

	for (i = 1; i < cmd->chanlist_len; i++) {
		unsigned int chan = CR_CHAN(cmd->chanlist[i]);
		unsigned int range = CR_RANGE(cmd->chanlist[i]);

		if (chan != (chan0 + i) % s->n_chan) {
			dev_dbg(dev->class_dev,
				"entries in chanlist must be consecutive channels, counting upwards\n");
			return -EINVAL;
		}
		if (range != range0) {
			dev_dbg(dev->class_dev,
				"entries in chanlist must all have the same gain\n");
			return -EINVAL;
		}
	}

	return 0;
}

static int dmm32at_ai_cmdtest(struct comedi_device *dev,
			      struct comedi_subdevice *s,
			      struct comedi_cmd *cmd)
{
	int err = 0;
	unsigned int arg;

	/* Step 1 : check if triggers are trivially valid */

	err |= comedi_check_trigger_src(&cmd->start_src, TRIG_NOW);
	err |= comedi_check_trigger_src(&cmd->scan_begin_src, TRIG_TIMER);
	err |= comedi_check_trigger_src(&cmd->convert_src, TRIG_TIMER);
	err |= comedi_check_trigger_src(&cmd->scan_end_src, TRIG_COUNT);
	err |= comedi_check_trigger_src(&cmd->stop_src, TRIG_COUNT | TRIG_NONE);

	if (err)
		return 1;

	/* Step 2a : make sure trigger sources are unique */

	err |= comedi_check_trigger_is_unique(cmd->stop_src);

	/* Step 2b : and mutually compatible */

	if (err)
		return 2;

	/* Step 3: check if arguments are trivially valid */

	err |= comedi_check_trigger_arg_is(&cmd->start_arg, 0);

	err |= comedi_check_trigger_arg_min(&cmd->scan_begin_arg, 1000000);
	err |= comedi_check_trigger_arg_max(&cmd->scan_begin_arg, 1000000000);

	if (cmd->convert_arg >= 17500)
		cmd->convert_arg = 20000;
	else if (cmd->convert_arg >= 12500)
		cmd->convert_arg = 15000;
	else if (cmd->convert_arg >= 7500)
		cmd->convert_arg = 10000;
	else
		cmd->convert_arg = 5000;

	err |= comedi_check_trigger_arg_is(&cmd->scan_end_arg,
					   cmd->chanlist_len);

	if (cmd->stop_src == TRIG_COUNT)
		err |= comedi_check_trigger_arg_min(&cmd->stop_arg, 1);
	else /* TRIG_NONE */
		err |= comedi_check_trigger_arg_is(&cmd->stop_arg, 0);

	if (err)
		return 3;

	/* Step 4: fix up any arguments */

	arg = cmd->convert_arg * cmd->scan_end_arg;
	err |= comedi_check_trigger_arg_min(&cmd->scan_begin_arg, arg);

	if (err)
		return 4;

	/* Step 5: check channel list if it exists */
	if (cmd->chanlist && cmd->chanlist_len > 0)
		err |= dmm32at_ai_check_chanlist(dev, s, cmd);

	if (err)
		return 5;

	return 0;
}

static void dmm32at_setaitimer(struct comedi_device *dev, unsigned int nansec)
{
	unsigned char lo1, lo2, hi2;
	unsigned short both2;

	/* based on 10mhz clock */
	lo1 = 200;
	both2 = nansec / 20000;
	hi2 = (both2 & 0xff00) >> 8;
	lo2 = both2 & 0x00ff;

	/* set counter clocks to 10MHz, disable all aux dio */
	outb(0, dev->iobase + DMM32AT_CTRDIO_CFG_REG);

	/* get access to the clock regs */
	outb(DMM32AT_CTRL_PAGE_8254, dev->iobase + DMM32AT_CTRL_REG);

	/* write the counter 1 control word and low byte to counter */
	outb(DMM32AT_CLKCT1, dev->iobase + DMM32AT_CLKCT);
	outb(lo1, dev->iobase + DMM32AT_CLK1);

	/* write the counter 2 control word and low byte then to counter */
	outb(DMM32AT_CLKCT2, dev->iobase + DMM32AT_CLKCT);
	outb(lo2, dev->iobase + DMM32AT_CLK2);
	outb(hi2, dev->iobase + DMM32AT_CLK2);

	/* enable the ai conversion interrupt and the clock to start scans */
	outb(DMM32AT_INTCLK_ADINT |
	     DMM32AT_INTCLK_CLKEN | DMM32AT_INTCLK_CLKSEL,
	     dev->iobase + DMM32AT_INTCLK_REG);
}

static int dmm32at_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
{
	struct comedi_cmd *cmd = &s->async->cmd;
	int ret;

	dmm32at_ai_set_chanspec(dev, s, cmd->chanlist[0], cmd->chanlist_len);

	/* reset the interrupt just in case */
	outb(DMM32AT_CTRL_INTRST, dev->iobase + DMM32AT_CTRL_REG);

	/*
	 * wait for circuit to settle
	 * we don't have the 'insn' here but it's not needed
	 */
	ret = comedi_timeout(dev, s, NULL, dmm32at_ai_status,
			     DMM32AT_AI_READBACK_REG);
	if (ret)
		return ret;

	if (cmd->stop_src == TRIG_NONE || cmd->stop_arg > 1) {
		/* start the clock and enable the interrupts */
		dmm32at_setaitimer(dev, cmd->scan_begin_arg);
	} else {
		/* start the interrupts and initiate a single scan */
		outb(DMM32AT_INTCLK_ADINT, dev->iobase + DMM32AT_INTCLK_REG);
		outb(0xff, dev->iobase + DMM32AT_AI_START_CONV_REG);
	}

	return 0;
}

static int dmm32at_ai_cancel(struct comedi_device *dev,
			     struct comedi_subdevice *s)
{
	/* disable further interrupts and clocks */
	outb(0x0, dev->iobase + DMM32AT_INTCLK_REG);
	return 0;
}

static irqreturn_t dmm32at_isr(int irq, void *d)
{
	struct comedi_device *dev = d;
	unsigned char intstat;
	unsigned int val;
	int i;

	if (!dev->attached) {
		dev_err(dev->class_dev, "spurious interrupt\n");
		return IRQ_HANDLED;
	}

	intstat = inb(dev->iobase + DMM32AT_INTCLK_REG);

	if (intstat & DMM32AT_INTCLK_ADINT) {
		struct comedi_subdevice *s = dev->read_subdev;
		struct comedi_cmd *cmd = &s->async->cmd;

		for (i = 0; i < cmd->chanlist_len; i++) {
			val = dmm32at_ai_get_sample(dev, s);
			comedi_buf_write_samples(s, &val, 1);
		}

		if (cmd->stop_src == TRIG_COUNT &&
		    s->async->scans_done >= cmd->stop_arg)
			s->async->events |= COMEDI_CB_EOA;

		comedi_handle_events(dev, s);
	}

	/* reset the interrupt */
	outb(DMM32AT_CTRL_INTRST, dev->iobase + DMM32AT_CTRL_REG);
	return IRQ_HANDLED;
}

static int dmm32at_ao_eoc(struct comedi_device *dev,
			  struct comedi_subdevice *s,
			  struct comedi_insn *insn,
			  unsigned long context)
{
	unsigned char status;

	status = inb(dev->iobase + DMM32AT_AUX_DI_REG);
	if ((status & DMM32AT_AUX_DI_DACBUSY) == 0)
		return 0;
	return -EBUSY;
}

static int dmm32at_ao_insn_write(struct comedi_device *dev,
				 struct comedi_subdevice *s,
				 struct comedi_insn *insn,
				 unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	int i;

	for (i = 0; i < insn->n; i++) {
		unsigned int val = data[i];
		int ret;

		/* write LSB then MSB + chan to load DAC */
		outb(val & 0xff, dev->iobase + DMM32AT_AO_LSB_REG);
		outb((val >> 8) | DMM32AT_AO_MSB_DACH(chan),
		     dev->iobase + DMM32AT_AO_MSB_REG);

		/* wait for circuit to settle */
		ret = comedi_timeout(dev, s, insn, dmm32at_ao_eoc, 0);
		if (ret)
			return ret;

		/* dummy read to update DAC */
		inb(dev->iobase + DMM32AT_AO_MSB_REG);

		s->readback[chan] = val;
	}

	return insn->n;
}

static int dmm32at_8255_io(struct comedi_device *dev,
			   int dir, int port, int data, unsigned long regbase)
{
	/* get access to the DIO regs */
	outb(DMM32AT_CTRL_PAGE_8255, dev->iobase + DMM32AT_CTRL_REG);

	if (dir) {
		outb(data, dev->iobase + regbase + port);
		return 0;
	}
	return inb(dev->iobase + regbase + port);
}

/* Make sure the board is there and put it to a known state */
static int dmm32at_reset(struct comedi_device *dev)
{
	unsigned char aihi, ailo, fifostat, aistat, intstat, airback;

	/* reset the board */
	outb(DMM32AT_CTRL_RESETA, dev->iobase + DMM32AT_CTRL_REG);

	/* allow a millisecond to reset */
	usleep_range(1000, 3000);

	/* zero scan and fifo control */
	outb(0x0, dev->iobase + DMM32AT_FIFO_CTRL_REG);

	/* zero interrupt and clock control */
	outb(0x0, dev->iobase + DMM32AT_INTCLK_REG);

	/* write a test channel range, the high 3 bits should drop */
	outb(0x80, dev->iobase + DMM32AT_AI_LO_CHAN_REG);
	outb(0xff, dev->iobase + DMM32AT_AI_HI_CHAN_REG);

	/* set the range at 10v unipolar */
	outb(DMM32AT_RANGE_U10, dev->iobase + DMM32AT_AI_CFG_REG);

	/* should take 10 us to settle, here's a hundred */
	usleep_range(100, 200);

	/* read back the values */
	ailo = inb(dev->iobase + DMM32AT_AI_LO_CHAN_REG);
	aihi = inb(dev->iobase + DMM32AT_AI_HI_CHAN_REG);
	fifostat = inb(dev->iobase + DMM32AT_FIFO_STATUS_REG);
	aistat = inb(dev->iobase + DMM32AT_AI_STATUS_REG);
	intstat = inb(dev->iobase + DMM32AT_INTCLK_REG);
	airback = inb(dev->iobase + DMM32AT_AI_READBACK_REG);

	/*
	 * NOTE: The (DMM32AT_AI_STATUS_SD1 | DMM32AT_AI_STATUS_SD0)
	 * test makes this driver only work if the board is configured
	 * with all A/D channels set for single-ended operation.
	 */
	if (ailo != 0x00 || aihi != 0x1f ||
	    fifostat != DMM32AT_FIFO_STATUS_EF ||
	    aistat != (DMM32AT_AI_STATUS_SD1 | DMM32AT_AI_STATUS_SD0) ||
	    intstat != 0x00 || airback != 0x0c)
		return -EIO;

	return 0;
}

static int dmm32at_attach(struct comedi_device *dev,
			  struct comedi_devconfig *it)
{
	struct comedi_subdevice *s;
	int ret;

	ret = comedi_request_region(dev, it->options[0], 0x10);
	if (ret)
		return ret;

	ret = dmm32at_reset(dev);
	if (ret) {
		dev_err(dev->class_dev, "board detection failed\n");
		return ret;
	}

	if (it->options[1]) {
		ret = request_irq(it->options[1], dmm32at_isr, 0,
				  dev->board_name, dev);
		if (ret == 0)
			dev->irq = it->options[1];
	}

	ret = comedi_alloc_subdevices(dev, 3);
	if (ret)
		return ret;

	/* Analog Input subdevice */
	s = &dev->subdevices[0];
	s->type		= COMEDI_SUBD_AI;
	s->subdev_flags	= SDF_READABLE | SDF_GROUND | SDF_DIFF;
	s->n_chan	= 32;
	s->maxdata	= 0xffff;
	s->range_table	= &dmm32at_airanges;
	s->insn_read	= dmm32at_ai_insn_read;
	if (dev->irq) {
		dev->read_subdev = s;
		s->subdev_flags	|= SDF_CMD_READ;
		s->len_chanlist	= s->n_chan;
		s->do_cmd	= dmm32at_ai_cmd;
		s->do_cmdtest	= dmm32at_ai_cmdtest;
		s->cancel	= dmm32at_ai_cancel;
	}

	/* Analog Output subdevice */
	s = &dev->subdevices[1];
	s->type		= COMEDI_SUBD_AO;
	s->subdev_flags	= SDF_WRITABLE;
	s->n_chan	= 4;
	s->maxdata	= 0x0fff;
	s->range_table	= &dmm32at_aoranges;
	s->insn_write	= dmm32at_ao_insn_write;

	ret = comedi_alloc_subdev_readback(s);
	if (ret)
		return ret;

	/* Digital I/O subdevice */
	s = &dev->subdevices[2];
	return subdev_8255_init(dev, s, dmm32at_8255_io, DMM32AT_8255_IOBASE);
}

static struct comedi_driver dmm32at_driver = {
	.driver_name	= "dmm32at",
	.module		= THIS_MODULE,
	.attach		= dmm32at_attach,
	.detach		= comedi_legacy_detach,
};
module_comedi_driver(dmm32at_driver);

MODULE_AUTHOR("Comedi http://www.comedi.org");
MODULE_DESCRIPTION("Comedi: Diamond Systems Diamond-MM-32-AT");
MODULE_LICENSE("GPL");