* Freescale QorIQ 1588 timer based PTP clock

General Properties:

  - compatible   Should be "fsl,etsec-ptp" for eTSEC
                 Should be "fsl,fman-ptp-timer" for DPAA FMan
  - reg          Offset and length of the register set for the device
  - interrupts   There should be at least two interrupts. Some devices
                 have as many as four PTP related interrupts.

Clock Properties:

  - fsl,cksel        Timer reference clock source.
  - fsl,tclk-period  Timer reference clock period in nanoseconds.
  - fsl,tmr-prsc     Prescaler, divides the output clock.
  - fsl,tmr-add      Frequency compensation value.
  - fsl,tmr-fiper1   Fixed interval period pulse generator.
  - fsl,tmr-fiper2   Fixed interval period pulse generator.
  - fsl,max-adj      Maximum frequency adjustment in parts per billion.

  These properties set the operational parameters for the PTP
  clock. You must choose these carefully for the clock to work right.
  Here is how to figure good values:

  TimerOsc     = selected reference clock   MHz
  tclk_period  = desired clock period       nanoseconds
  NominalFreq  = 1000 / tclk_period         MHz
  FreqDivRatio = TimerOsc / NominalFreq     (must be greater that 1.0)
  tmr_add      = ceil(2^32 / FreqDivRatio)
  OutputClock  = NominalFreq / tmr_prsc     MHz
  PulseWidth   = 1 / OutputClock            microseconds
  FiperFreq1   = desired frequency in Hz
  FiperDiv1    = 1000000 * OutputClock / FiperFreq1
  tmr_fiper1   = tmr_prsc * tclk_period * FiperDiv1 - tclk_period
  max_adj      = 1000000000 * (FreqDivRatio - 1.0) - 1

  The calculation for tmr_fiper2 is the same as for tmr_fiper1. The
  driver expects that tmr_fiper1 will be correctly set to produce a 1
  Pulse Per Second (PPS) signal, since this will be offered to the PPS
  subsystem to synchronize the Linux clock.

  Reference clock source is determined by the value, which is holded
  in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the
  value, which will be directly written in those bits, that is why,
  according to reference manual, the next clock sources can be used:

  For eTSEC,
  <0> - external high precision timer reference clock (TSEC_TMR_CLK
        input is used for this purpose);
  <1> - eTSEC system clock;
  <2> - eTSEC1 transmit clock;
  <3> - RTC clock input.

  For DPAA FMan,
  <0> - external high precision timer reference clock (TMR_1588_CLK)
  <1> - MAC system clock (1/2 FMan clock)
  <2> - reserved
  <3> - RTC clock oscillator

  When this attribute is not used, the IEEE 1588 timer reference clock
  will use the eTSEC system clock (for Gianfar) or the MAC system
  clock (for DPAA).

Example:

	ptp_clock@24e00 {
		compatible = "fsl,etsec-ptp";
		reg = <0x24E00 0xB0>;
		interrupts = <12 0x8 13 0x8>;
		interrupt-parent = < &ipic >;
		fsl,cksel       = <1>;
		fsl,tclk-period = <10>;
		fsl,tmr-prsc    = <100>;
		fsl,tmr-add     = <0x999999A4>;
		fsl,tmr-fiper1  = <0x3B9AC9F6>;
		fsl,tmr-fiper2  = <0x00018696>;
		fsl,max-adj     = <659999998>;
	};